Shark SV726N User Manual

OWNER’S MANUAL

Model SV726N

14.4 V DC

Cordless Hand Vac

EURO-PRO Operating LLC

U.S.: 94 Main Mill Street, Door 16 Canada: 4400 Bois-Franc

Plattsburgh, NY 12901 St-Laurent, QC H4S 1A7

Tel.: 1-866-98SHARK

(1-866-987-4275)

www.sharkvac.com

Model SV726N

ONE (1) YEAR LIMITED WARRANTY

EURO-PRO Operating LLC warrants this product to be free from defects in
material and workmanship for a period of one (1) year from the date of the
original purchase, when utilized for normal household use, subject to the
following conditions, exclusions and exceptions.

If your appliance fails to operate properly while in use under normal household
conditions within the warranty period, return the complete appliance and
accessories, freight prepaid to

EURO-PRO Operating LLC, 94 Main Mill Street, Door 16, Plattsburgh, N.Y. 12901

If the appliance is found to be defective in material or workmanship, EURO-
PRO Operating LLC will repair or replace it free of charge. Proof of purchase
date and $ 9.95 to cover the cost of return shipping and handling must be
included. *

Non-durable parts including, without limitation, dust cup filters, filters, brushes
and electrical parts which normally require replacement are specifically
excluded from warranty.

The liability of EURO-PRO Operating LLC is limited solely to the cost of the
repair or replacement of the unit at our option. This warranty does not cover
normal wear of parts and does not apply to any unit that has been tampered
with or used for commercial purposes. This limited warranty does not cover
damage caused by misuse, abuse, negligent handling or damage due to faulty
packaging or mishandling in transit. This warranty does not cover damage or
defects caused by or resulting from damages from shipping or repairs, service
or alterations to the product or any of its parts, which have been performed by a
repair person not authorized by EURO-PRO Operating LLC.

This warranty is extended to the original purchaser of the unit and excludes all
other legal and/or conventional warranties. The responsibility of EURO-PRO
Operating LLC if any, is limited to the specific obligations expressly assumed
by it under the terms of the limited warranty. In no event is EURO-PRO
Operating LLC liable for incidental or consequential damages of any nature
whatsoever. Some states do not permit the exclusion or limitation of incidental
or consequential damages, so the above may not apply to you.

This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.

*Important: Carefully pack item to avoid damage in shipping. Be sure to
include proof of purchase date and to attach tag to item before packing
with your name, complete address and phone number with a note giving
purchase information, model number and what you believe is the problem
with item. We recommend you insure the package (as damage in shipping
is not covered by your warranty). Mark the outside of your package
“ATTENTION CUSTOMER SERVICE”. We are constantly striving to
improve our products, therefore the specifications contained herein are
subject to change without notice.

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic safety precautions should always be
observed, including the following

READ ALL INSTRUCTIONS BEFORE USING YOUR CORDLESS HAND VACUUM.

WARNING: To reduce the risk of fire, electrical shock, or injury:

1. Do not charge this unit outdoors.

2. Do not use outdoors or on wet surfaces.

3. Do not allow to be used as a toy. Close
attention is necessary when used by or
near children.

4. Use only as described in this manual.

5 Use only manufacturer’s recommended

attachments.

6. Do not use charger if power cord has
been damaged. Do not use cordless
hand vacuum or charger if it has been
dropped, damaged, left outdoors, or
dropped in water. Return it to EURO-
PRO Operating LLC for examination,
repair or adjustment.

7. Do not abuse the charger cord. Never
carry the charger or base by the cord or
yank to disconnect from an outlet;
instead grasp the plug and pull to
disconnect.

8. Keep charger cord away from heated
surfaces.

9. This product includes rechargeable
nickel cadmium batteries. Batteries must
be recycled or disposed of properly. Do

not incinerate batteries or expose to
high temperatures, as they may

explode.

10. Do not handle plug or appliance with wet
hands.

11. Do not put any object into openings. Do
not use with any opening blocked; keep
free of dust, lint, hair and anything that
may reduce air flow.

12. Keep hair, loose clothing, fingers, and all
parts of body away from openings and
moving parts.

13. Do not pick up anything that is burning
or smoking, such as cigarettes,
matches, or hot ashes.

14. Do not attempt to change accessories while
unit is running.

15. Use extra care when cleaning on stairs.

16. Do not use to pick up flammable or
combustible liquids such as gasoline or use
in areas where they may be present.

17. Look on your hand vacuum and follow all
label and marking instructions.

18. Do not use charger with an extension cord.
Plug charger directly into an electrical
outlet. Use charger only in a standard
(120V., 60Hz) electrical outlet.

19. Do not use the hand vacuum cleaner

without dust cup filter in place.

20. Store the cordless vacuum indoors. Put the
cordless vacuum away after use to prevent
accidents.

21. Leaks from battery cells can occur under
extreme conditions. If the liquid, which is 20­35% solution of potassium hydroxide, gets
on the skin - wash immediately with soap
and water or neutralize with a mild acid such
as lemon juice or vinegar. If the liquid
gets into the eyes, flush them immediately
with clean water for a minimum of 10
minutes and seek medical attention.

22. Use only on dry, indoor surfaces.

23. Do not use for any purpose other than
described in this user’s guide.

24. Do not attempt to use the charger with any
other product nor attempt to charge this
product with another charger. Use only the

charger model KA12D220020034U
supplied with this appliance
manufactured by Kuantech Co. Ltd..

25. "Ni-Cd" battery must be recycled or disposed
of properly.

SAVE THESE INSTRUCTIONS

For Household Use Only

1

Rev. 07/04

7Printed in China

Cordless Hand Vac

Model SV 726N

14.4 V DC

REPLACEMENT FILTERS

TO ORDER REPLACEMENT FILTERS OR

BATTERY PACKS

for Model SV726N

Replacement dust cup filter SKU# XSB726N

Replacement battery pack SKU# XB14726

Call: 1-866-98SHARK (1-866-987-4275)
Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time

or

visit our website: www.sharkvac.com

FOR TECHNICAL SUPPORT

In U.S.: 800-798-7398
Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time

Please Note

The Dust Cup Filter is washable. It should, however, be replaced every three
(3) months to ensure peak performance of your vacuum.

Important

Make sure that Dust Cup Filter is completely dry before re-installing back
in the hand vacuum.

1. Dust Cup Container

2. Dust cup filter

3. Dust cup release button

4. On/Off Button

5. Charging Indicator Light

6. Main Unit

7. Dusting Brush

8. Charging Stand

9. Crevice Tool

10.Charging Adapter

11.Motorized Brush

NOTE: Cordless vacuum Model SV726N is shipped with the

batteries uncharged. Charging of the unit for 20
hours prior to first use is required.

2

7

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

TROUBLESHOOTING GUIDE

PROBLEM POSSIBLE REASON POSSIBLE SOLUTION

HAND VACUUM
WILL NOT
OPERATE

MOTORIZED
BRUSH WI LL NOT
WORK

HAND VACUUM
WILL NOT PI CK­UP OR SUCTION
POWER I S WEAK

DUST ESCAPI NG
FROM HAND
VACUUM

1. Batteries discharged.

2. Dead battery (batter y
won't hold charge).

3. Contacts between the
unit and the charging
stand are di rty.

4. No power in electri cal
outlet supplying
transformer.

1. The 2 metal pins of
the motori zed brush
are not in contact
with the vacuum
cleaner.

2. Motorized brush is
clogged up.

1. Dust cup container i s
full.

2. Dust cup filter needs
cleaning or
repl acement.

3. Unit needs
rechargi ng.

1. Dust cup container i s
full.

2. Dust cup filter is not
installed correctly.

3. Puncture/hole i n dust
cup filter.

1. Charge unit.

2. Replace batteries. (See
page 5.)

3. Wipe and clean dirt from
contacts.

4. Check fuse or breaker.
Replace fuse/reset
breaker.

1. Firmly insert the
motori zed brush into the
air-intake nozzle. This
will connect t he
motori zed nozzl e to the
unit power suppl y.

2. Remove all lint, hair et c.
from motori zed brush.

1. Empty dust cup
container

2. Remove dust cup filter
and check for object(s)
in air duct and remove.
Clean or replace dust
cup filter.

3. Charge unit.

1. Empty dust cup
container.

2. Review dust cup fil ter
installation instructions.

3. Replace dust cup fi l ter.

Before Use

1. This cordless vacuum is powered by
rechargeable nickel-cadmium
batteries. Before using the vacuum,
charge the vacuum cleaner for a
minimum of 20 hours.

NOTE: Ensure that the On/Off
switch is in the “Off” position
before charging.

NOTE: Peak performance may only

be realized after the unit has been
charged and discharged two (2) or
three (3) times.

IMPORTANT: To maintain peak
performance of your cordless hand
vacuum, it is recommended that the
unit be fully discharged, then
completely re-charged at least once a
month.

2. Store the vacuum cleaner in the
charging base when not in use so that
it is always charged and ready to
use.

Charging Your Vacuum Cleaner

1. Place the charging base
near an electrical power
outlet (120 V., 60 Hz.)
and plug in the chaging
adapter's jack into the
charging base.

2. Plug the charger into wall
outlet.

3. Place the unit in the
charging base. The
charging indicator light
will shine green to
indicate that the vacuum
cleaner is properly
positioned in the
charging base and that
the unit is being charged. (See Fig. 1)

Fig. 1

NOTE: Ensure that the On/Off
switch is in the "Off" position
before charging.

4. Always return the unit to the charging
base immediately after use so that it
will be ready and fully charged for it's
next use.

Assembly

Note: Dust cup filter must always be
used when operating the hand
vacuum.

1. To open the dust cup compartment,
push the dust cup release button
and remove the dust cup
container. (Fig. 2)

2. Verify that the dust cup filter is
inside, then re-attach the dust cup
container to the hand vacuum.
(Fig. 3)

Fig. 2

Fig. 3

3. To attach the crevice tool or the
dusting brush to the hand vacuum,
push the attachment into the
suction hole in the front of the
dust container. (Fig. 4)

Fig. 4

3

6

OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS

Using Your Cordless Vacuum

1. Remove the vacuum cleaner from
the charging base

2. To start the unit, push the "On/Off"
switch to the "On" position.

3. To stop the vacuum cleaner, slide
the "On/Off" switch to the "Off"
position.

4. A crevice tool is provided for
cleaning narrow, hard to reach
places. A dusting brush is provided
for cleaning upholstery, furniture,
etc.

Using Your Motorized Brush

1. Remove the vacuum cleaner from
the charging base

2. Make sure that it is in the "Off"
position.

3. Firmly insert the motorized brush
(Fig. 5) into the air-intake nozzle of
the dust cup container ensuring
that the contact pins are engaged
in the connector slots of the unit.
(Fig. 6)
Please note that this motorized
brush is for vacuuming short pile
carpets or rugs.

Metal

contact

pins

Fig. 5

Fig. 6

WARNING: Do not touch the
motorized brush while it is in motion.

Changing & Cleaning the Dust Cup
Filter

To achieve the best performance,
empty the dust cup container and
clean the dust cup filter after each use.

1. To remove the dust cup container,
press down on the dust cup release
button and pull off the dust cup
container.

2. Pull out the dust cup filter.

3. Empty the dust from the dust cup
container. (See Fig. 7)

4. Rinse the dust cup filter in cold water,
and then wait until it dries completely
before replacing it back into the dust
cup container. Do not use a washing
machine to clean the dust cup filter.
Do not use a hair dryer to dry it. Air

dry only.

5. Replace the dust cup filter carefully
into the dust cup compartment.
NEVER operate vacuum cleaner
without dust cup filter in place.

6. Attach the dust cup container to the
cordless vacuum.

Fig. 7

NOTE: It is recommended that the dust
cup filter be replaced every three (3)
months to ensure peak performance of
the unit.

CAUTION: The suction hole must be
open and free of any obstructions at all
times. Otherwise, the motor will
overheat and could become damaged.

WARNING: NEVER use ordinary
batteries for replacement, as these may
leak and damage your vacuum cleaner.

Battery Pack Replacement
& Disposal

Model SV726N Cordless Vacuum is
powered by Nickel-Cadmium Ni-Cd)
batteries, which must be recycled or
disposed of properly in accordance
with state, federal and local laws.

If uncertain as to how to remove the
battery pack, we suggest you take your
hand vacuum to a reputable small
appliance service technician to have
this service preformed.

Do NOT attempt to replace the
batteries used in this product with any
other type of battery.

The battery pack of your SV726N is
replaceable, however care should be
taken when doing so. Follow these steps
when replacement is required:

1. Using a #1 Phillips head screw driver,
remove the single screw securing the
battery compartment cover located on
the under side of the unit.

2. To remove the cover, press down on
the battery compartment cover while
sliding towards the rear of the unit.
NEVER open the battery
compartment except to change the
battery.

3. Set aside battery compartment cover
and screw.

4. Using the same Phillips screw driver,
remove the single screw securing the
battery strap. Lift off the battery strap
and set aside with screw.

5. Carefully lift out battery pack and
disconnect the terminals.

6. Connect the terminals to the new
battery pack taking care to connect
the black lead (-) to the negative
connector first and the red lead (+) to
the positive connector second. Place
the new battery into the battery
compartment.

7. Tuck the wiring inside the battery
compartment so that the wiring does
not interfere with the battery
compartment cover when it is
replaced.

8. Re-install the battery strap and
battery compartment cover.

WARNING: NEVER use ordinary
batteries for replacement, as these may
leak and damage your vacuum cleaner.

Use only battery pack XB14726 provided by
EURO-PRO Operating LLC for
replacement.

CAUTION: NEVER use the unit
without the battery compartment cover
in place.

NOTE: Any other servicing should be
performed by an authorized service
representative.

CAUTION

• Use only with the battery pack

supplied with the unit.

• Do not attempt to remove the battery
pack from the unit to charge it.

• Never attempt to throw the battery
pack or unit into a fire or incinerate it.

• Do not attempt to remove or damage
the battery casing.

• Battery must be recycled or disposed
of properly at the end of it's
service life.

Wall Mounting Bracket (Optional)

1. Make sure that the intended wall area
for the wall mounting bracket to be
drilled is free from any hidden
electrical wires, water pipes and gas
lines.

2. Select an appropriate place close to a
wall power outlet (120V., 60 Hz).

3. Do not mount near direct sunlight,
near a heat source or outdoors.

4. Select an appropriate drill type for the
material to be drilled.

5. Carefully measure and mark the
location of all bracket holes and

then drill holes and screw the wall

mounting bracket onto the wall.

4

5