Shark S3455UKL, STEAM POCKET MOP S3455UKL Owner's Manual

S3455UKL

OWNER’S GUIDE

Professional SLIM
STEAM POCKET® MOP

Freephone: 0800 862 0453

WHEN USING YOUR SHARK®
STEAM MOP, BASIC SAFETY
PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED,
INCLUDING THE FOLLOWING:

READ ALL INSTRUCTIONS
BEFORE USING YOUR
STEAM MOP.

DANGER OF SCALDING.

Please use caution when
using the steam mop. The steam
emitted from the steam mop is
very hot.

IMPORTANT:

This appliance is not intended
for use by persons (including
children) with reduced physical,
sensory or mental capabilities
or lack of experience and
knowledge, unless they have
been given supervision or
instruction concerning the use
of the appliance by a person
responsible for their safety.

Children should be supervised
to ensure that they do not play
with the appliance.

WARNING:

TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY:

1.

Use the system only for its intended
use.

2. DO NOT use outdoors.

3.

DO NOT leave the appliance
unattended when plugged in.
Always unplug the power cord from
the electrical outlet when not in use
and before servicing.

4. DO NOT allow the appliance to be
used by children. Close attention
is necessary when used by or near
children, pets or plants.

5. Children should be supervised to
ensure that they do not play with the
appliance.

6. Use only as described in this manual.

7 . Use only manufacturer’s

recommended accessories.

8. DO NOT operate the appliance with
a damaged plug or cord, or if the
unit has been dropped or damaged.
To avoid the risk of electric shock,
do not disassemble or attempt to
repair the appliance on your own. If
the supply cord is damaged, it must
be replaced by a qualified electrician
in order to avoid a hazard. Incorrect
re-assembly or repair can cause a
risk of electrical shock or injury to
persons when the appliance is used.

9. To protect against a risk of electric
shock, DO NOT immerse the steam
mop into water or any other liquids.

10. DO NOT handle plug or steam mop
with wet hands or operate appliance
without shoes.

11. DO NOT pull or carry by power cord,
use power cord as handle, close a
door on the power cord, or pull the
power cord around sharp edges or
corners. Keep power cord away from
heated surfaces.

IMPORTANT SAFETY INSTRUCTIONS

For Household Use Only

www.lakeland.co.uk

12. DO NOT unplug by pulling on
power cord. To unplug, grasp the
plug not the power cord. Do not
use extension cords or outlets
with inadequate current carrying
capacity.

13. DO NOT put any objects into
openings. Do not use with any
opening that is blocked.

14. DO NOT put hands or feet under the
steam mop. Unit gets very hot.

15. Use O N LY on flat, horizontal
surfaces. Do not use on walls,
counters or windows.

16. DO NOT use on leather, wax polished
furniture or floors, synthetic fabrics,
velvet or other delicate, steam
sensitive materials.

17. Liquid or steam must not be directed
towards equipment containing
electrical components, such as the
interior of ovens.

18. DO NOT add cleaning solutions,
scented perfumes, oils or any other
chemicals to the water used in this
appliance as this may damage the
unit or make it unsafe for use. If
you live in a hard water area, we
recommend using distilled water in
your steam mop.

19. When in use, NEVER turn the
appliance over or on its side. NEVER

DIRECT STEAM TOWARDS PEOPLE,
ANIMALS OR PLANTS.

20. NEVER LEAVE THE STEAM MOP IN
ONE SPOT ON ANY SURFACE FOR
ANY PERIOD OF TIME WHEN THE
CLEANING POCKET IS ATTACHED
AS THIS WILL DAMAGE YOUR
FLOORS.

21. Carefully remove the cleaning
pocket immediately after you have
unplugged and allowed the steam
mop to cool.

22. When cleaning the steam mop,
unplug the power cord from the
electrical outlet and clean with a dry
or damp cloth. Do not pour water or
use alcohol, benzene or paint thinner
on the unit.

23. Extreme caution should be
exercised when using this appliance
to clean stairs.

24. Never use steam mop without the
cleaning pocket attached.

25. Keep your work area well lit.

26. Store steam mop indoors in a cool,
dry place.

27. To avoid circuit overload, do not
operate another appliance on the
same socket (circuit) as the steam
cleaner.

28. If an extension cord is absolutely
necessary, an extension cord rated
a minimum of 15 ampere, 14 gage
cord should be used. Cords rated for
less amperage may overheat. Care
should be taken to arrange cord so
that it cannot be pulled or tripped
over.

29. DO NOT leave unattended when
the system is connected to a power
supply or electrical outlet. Turn off
all controls before unplugging the
unit.

3 0 . DO NOT store unit with damp or wet

cleaning pocket attached. Never
leave the steam mop in one spot on
any surface for any period of time
with a damp or wet cleaning pocket
attached as this will damage your
floors

31. Always unplug and allow the steam
mop to cool before removing or
changing mop heads.

32. Make sure that the water tank door
closed when using the appliance.

WARNING: Your steam mop is

designed to clean hard floor surfaces
that will withstand high heat. Do not
use on unsealed wood or unglazed
ceramic floors. On surfaces that
have been treated with wax or some
no wax floors, the sheen may be
removed by the heat and steam
action. It is always recommended to
test an isolated area of the surface to
be cleaned before proceeding. We
also recommend that you check the
use and care instructions from the
floor manufacturer.

SAVE THESE
INSTRUCTIONS

Freephone: 0800 862 0453

This manual covers model:
S3455UKL 11

TECHNICAL SPECIFICATIONS
Voltage: 220-240V~, 50/60Hz.
Power: 1550 Watts
Water Capacity: 300 ml

This appliance complies with the WEEE-Directive 2002/96/EC on the disposal of
electrical and electronic equipment (WEEE).

This appliance complies with the European directives for electromagnetic
compatibility (EMC) 2004/108/EC and its revisions, as well as Low Voltage
Directive (LVD) 2006/95/EC and its revisions.

This marking indicates that this product should not be disposed with
other household wastes throughout the EU. To prevent possible harm
to the environment or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse of material
sources. To return your used device, please use the return and collection
systems or contact the retailer where this product was purchased. They
can take this product for environmental safe recycling.

This product has no on/off switch and operates when plugged into the main supply
source. Disconnect the plug from mains after use.

Although the product is not provided with standby mode or off mode, it still fulfills
the requirements of 1275/2008/EC - the directive for Eco-Design requirements
since according to technical justification, it is considered as inappropriate to provide
standby and off modes when connecting to mains. To reduce energy consumption
be sure to unplug the unit after use.

1

www.lakeland.co.uk

Contents

Getting Started ......................................................................2

Using Your Steam Mop .......................................................5

Using Your Carpet Glider ...................................................7

Care of Your Steam Mop ....................................................8

Troubleshooting Guide .......................................................10

Thank you
for purchasing
the Shark

®

Professional SLIM

Steam Pocket

®

Mop.

2

Freephone: 0800 862 0453

Getting Started

When assembling your steam mop
there may be a little water in or around
the water tank. This is because we test
all our steam mops 100% before you
buy them, so you get a quality Shark®
Professional SLIM Steam Pocket® Mop.

h Quick Release Swivel Cord Wrap

i Cord Clip

j Water Tank

k STEAM CONTROL Button

l Mop Head Release Button

a Steam Mop Body

b Mop Handle

c All-Purpose Mop Head (1)

d Cleaning Pockets for the All-Purpose

Mop Head (2)

e Carpet Glider

f Filling Flask

g (1) 6mm x 52mm Large Screw*

*Phillips or flat head screwdriver can be
used. Screwdriver not included.

b

a

c

e

h

i

j

k

l

f

d

g

3

www.lakeland.co.uk

IMPORTANT: Always make sure the
mop is UNPLUGGED from the wall
when not in use. Never fill the mop,
attach the mop head, change or
remove the cleaning pocket when
the mop is plugged into the wall.
To prolong the life of your Shark®
Professional SLIM Steam Pocket®
Mop, we recommend using distilled
water. Make sure you only add water
to the tank. Chemicals or cleaning
solution may damage the appliance
and could be unsafe for you and your
family.

ASSEMBLE

1 Insert the Mop handle end labeled

“Front” into the steam mop body.
Make sure it is inserted past the
line printed on the pole. Secure the
assembled handle and pole by using
the large screw and a Phillips or a flat
head screwdriver (screwdriver not
included). (fig. 1)

fig. 1

4

Freephone: 0800 862 0453

Getting Started - cont’d

IMPORTANT: Do not use on unsealed

wood or unglazed ceramic floors.
On surfaces that have been treated
with wax or some no wax floors,
the sheen may be removed by
the heat and steam action. It is
always recommended to test an
isolated area of the surface to be
cleaned before proceeding. We
recommend that you check the use
and care instructions from the floor
manufacturer.

2 Use the loop on the side of the

cleaning pocket to slide the mop
head into the pad pocket. Then
secure the quick fasteners on the top
of the pocket to lock in place. (fig. 2)

3 Snap the mop head into the base to

secure it. (fig. 3)

4 Open the water tank door. (fig. 4)

Use the filling flask and pour water

into the tank. Do not overfill. Press
the water tank door firmly to close.
(fig. 5)

fig. 2

fig. 3

fig. 4

fig. 5

5

www.lakeland.co.uk

s

t

e

a

m

c

o

n

t

r

o

l

IMPORTANT: Sweep or vacuum your

floors prior to cleaning with your
Steam Mop.

1 Pull and twist the quick release cord

holder to unwrap the power cord
completely. Plug into an electrical
outlet. (fig. 6)

2 The STEAM CONTROL button will

flash blue. If the light does not turn
on, reference the troubleshooting
section on page 10. (fig. 7)

IMPORTANT: Do not use the mop

without attaching a cleaning pocket
and adding water to the tank first.
When you are using the mop for
the first time, it might take longer
than the normal 30 seconds to start
steaming.

Using Your Steam Mop

fig. 6

fig. 7

6

Freephone: 0800 862 0453

s

te

a

m

c

o

n

t

r

o

l

Using Your Steam Mop - cont’d

3 Press the STEAM CONTROL button

once to activate the LOW steam
setting.

Press the STEAM CONTROL button

twice to activate the HIGH steam
setting.(fig. 8)

Use the scrubbing side of the cleaning

pockets when using the HIGH steam
setting.

4 Clean your floors with a forward and

backward motion. (fig. 9)

To stop the steam, press the STEAM

CONTROL button a third time.

The STEAM CONTROL button will

flash blue to indicate the mop is in
STANDBY mode.

fig. 8

fig. 9

7

www.lakeland.co.uk

THE CARPET GLIDER

1 The Carpet Glider can be used with

the All-Purpose Head to lightly steam
your carpet and area rugs. Just place
the mop head with the cleaning
pocket attached into the glider. The
recommended steam setting is HIGH
when using the Carpet Glider.
(fig. 11)

2 Move the Steam Mop back and forth

across a section of the carpet.
(fig. 12)

5 Use the shaggy side of the cleaning

pockets to lift up and lock away all
the dirt and debris and the scrubbing
side to break up the tough stains.
(fig. 10)

6 When the water tank is empty, the

steam mop will stop producing
steam. You can refill the water
tank at any time as long as the
mop is unplugged from the outlet.
Reference the filling instructions
from page 4.

NOTE: Please wait 2-3 minutes

for the Steam Mop to cool off
before removing the mop head or
the cleaning pocket. Never leave
the steam mop with a damp/wet
cleaning pocket on any floor.

fig. 10

Using Your Carpet Glider

fig. 11

The Steam Mop will not clean your
carpeting or area rugs. However, it is
great for grooming and freshening.

fig. 12

8

Freephone: 0800 862 0453

2 Empty the water tank before storage.

Open the water tank door and empty
the tank over a sink. Close the water
cap. (fig. 14)

3 To store the Shark

®

Professional SLIM

Steam Pocket® Mop hanging up, first
remove the head (after it has cooled
and the steam has been released)
then hang on a large hook. (fig. 15)

AFTER USE AND STORAGE

1 When you have finished using

the steam mop, press the STEAM
CONTROL button until the LED light

turns flashing BLUE. This stops the
unit from steaming. Unplug the cord
from the outlet and place the mop
into the upright position. Let the unit
cool for 2-3 minutes.

Remove the cleaning pocket by

releasing the quick fasteners and
using the lavender loop on the side
of the pocket, avoiding contact with
the hot pocket or dirt. (fig. 13)

Care of Your Steam Mop

fig. 13

fig. 14

fig. 15

9

www.lakeland.co.uk

CARE OF YOUR CLEANING POCKET

1 We recommend washing your

cleaning pocket separately from
other fabrics to avoid picking up
lint. Only use liquid detergent (no

powder detergent). Do not use
any fabric softeners or bleach.

For optimal cleaning performance
pockets may need to be washed up
to (3) three times. Line dry. Do not
tumble dry. (fig. 16)

2 If there are loose threads on the

cleaning pocket carefully cut the
thread with scissors. Do not pull on
them or cut at the base. (fig. 17)

DECALCIFYING YOUR STEAM MOP

Calcium and mineral deposits can

build up and impact the performance
of your steam mop over time.

CLEANING THE NOZZLE
Your steam mop should not normally

require cleaning, however, should
you notice a decrease in the steam
output, it may be necessary to
remove mineral deposits built up

around the nozzle.

1 Unplug the steam mop from the

electrical outlet.

2 Use a small diameter stiff metal

wire, such as a straightened metal
paperclip, and carefully insert the
end of the wire into the nozzle
orifice. (fig. 18)

3 Move the wire back and forth several

times to remove any deposits.

4 Plug the steam mop in to the power

outlet and test steam output.

fig. 16

fig. 17

fig. 18

40°

PART PART NO.

1 2 Cleaning Pockets XT3701UKL

2 Carpet Glider XCG200

ORDERING REPLACEMENT PARTS

To order additional parts and

accessories, feel free to contact us at:

Shark Customer Services
PO Box 298
Mirfield
WF14 9BA
Freephone 0800 862 0453

10

Freephone: 0800 862 0453

Troubleshooting Guide

PROBLEM POSSIBLE REASONS & SOLUTIONS

The Professional SLIM

Steam Pocket

®

Mop

will not turn-on.

Your steam mop should be securely plugged into an electrical
outlet only.

Check your fuse or breaker.

If your unit still does not work, give us a call at:

Freephone 0800 862 0453.

The unit will not
make steam.

Is there water in the water tank? If not, add water to your steam
mop following instructions on page 4.

If the unit still doesn’t make steam, follow the decalcification
instructions on page 9.

Cannot select steam
setting/flashing blue
light remains on.

If you have already plugged in your unit, unplug and try a
different outlet. This may reset the Standby mode.

Add water to the tank and press the STEAM CONTROL button
to select a steam setting.

If your unit still does not work, call 0800 862 0453.

The Professional SLIM

Steam Pocket® Mop

leaves water on the
floor.

Check to see if your cleaning pocket is soaked through. We
recommend you unplug the steam mop and change the
cleaning pocket.

Make sure the cleaning pocket is attached correctly.

The Professional SLIM

Steam Pocket® Mop

left a white spot on
the floor.

Do not leave your steam mop on the floor with a damp or wet
cleaning pocket.

If you’re using tap water we recommend switching to
distilled water.

Make sure the cap is securely on the water tank.

Floors are cloudy,
streaky or spotty
after steaming.

The pocket might be dirty, change the pocket.
If you washed the cleaning pocket with powder detergent, then

it might be ruined.
You might have left the mop in the same spot for too long. Do

you have hard water? If you do, you might want to switch to
distilled water.

This might be leftover from past cleaners used on the floor
surface. Use the steam mop a few more times and see if the
leftover cloudiness is removed. If this does not work, we
suggest rinsing the floor with water, letting it dry, and then
steam mopping again with a clean pocket. One or more rinses
generally removes the residue. A more stubborn case may
require you to rinse the floor with a mix of one part vinegar and
two parts water.

The Professional SLIM

Steam Pocket® Mop is

hard to push.

Make sure the cleaning pocket is attached correctly.
Check to see if the cleaning pocket is excessively dirty. Replace

if the cleaning pocket is too dirty or wet.

11

www.lakeland.co.uk

Notes

Shark Customer Services
PO Box 298
Mirfield
WF14 9BA
Freephone 0800 862 0453
www.lakeland.co.uk

Technical Details
Model number: S3455UKL 11
Input: 1550 Watts

Main unit voltage: 220-240V~, 50/60 Hz.

COPYR IGHT© EURO -PRO OPER ATING LLC 2013

PRIN TED IN CHIN A

S3455UKL.E.130508. 5

Illus tration s may differ from a ctual produ ct.