WWW.SHARKCLEAN.COM
PRO
STEAM POCKET® MOP
S3601
OWNER’S GUIDE
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
For Household Use Only
WHEN USING YOUR SHARK
STEAM MOP, BASIC SAFETY
PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED,
INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS
BEFORE USING YOUR
STEAM MOP.
DANGER OF SCALDING.
Please use caution when
using the steam mop. The steam
emitted from the steam mop is
very hot.
POLARIZED PLUG:
This appliance has a polarized
plug (one blade is wider than
the other). As a safety feature,
this plug will fit into a polarized
outlet only one way. If the
plug does not fit fully into the
outlet, reverse the plug. If it still
does not fit, contact a qualified
electrician. Do not attempt to
defeat this safety feature.
1. Use the system only for its
intended use.
2. DO NOT use outdoors.
3. DO NOT leave the appliance
unattended when plugged in.
Always unplug the power cord
from the electrical outlet when not
in use and before servicing.
4. DO NOT allow the appliance to be
used by children. Close attention
is necessary when used by or near
children, pets or plants.
5. Use only as described in this
manual.
6. Use only manufacturer’s
recommended accessories.
7. DO NOT operate the appliance
with a damaged plug or cord, or
if the unit has been dropped or
damaged. To avoid the risk of
electric shock, do not disassemble
or attempt to repair the appliance
on your own. Return the appliance
to EURO-PRO Operating LLC for
examination and repair. Incorrect
re-assembly or repair can cause
a risk of electrical shock or injury
to persons when the appliance is
used.
8. To protect against a risk of electric
shock, DO NOT immerse the steam
mop into water or any other liquids.
9. DO NOT handle plug or steam
mop with wet hands or operate
appliance without shoes .
10. DO NOT pull or carry by power
cord, use power cord as handle,
close a door on the power cord, or
pull the power cord around sharp
edges or corners. Keep power cord
away from heated surfaces.
TOL L F RE E: 1-80 0-79 8-739 8
Eng lis h
11. DO NOT unplug by pulling on
power cord. To unplug, grasp the
plug not the power cord. Do not
use extension cords or outlets
with inadequate current carrying
capacity.
12. DO NOT put any objects into
openings. Do not use with any
opening that is blocked.
13. DO NOT put hands or feet under
the steam mop. Unit gets very hot.
14. Use ONLY on flat, horizontal
surfaces. Do not use on walls,
counters or windows .
15. DO NOT use on leather, wax
polished furniture or floors,
synthetic fabrics, velvet or other
delicate, steam sensitive materials.
16. DO NOT add cleaning solutions,
scented perfumes, oils or any other
chemicals to the water used in this
appliance as this may damage the
unit or make it unsafe for use. If
you live in a hard water area, we
recommend using distilled water in
your steam mop.
17. When in use, NEVER turn the
appliance over or on its side.
NEVE R DIRECT STEAM TOWARDS
PEOPLE, ANIMALS OR PLANTS.
18. NEVE R LEAVE THE STEAM MOP
IN ONE SPOT ON ANY SURFACE
FOR ANY PERIOD OF TIME WHEN
MICRO -FIBER PAD IS ATTACHED
AS THIS WILL DAMAGE YOU R
FLOORS.
19. Carefully remove the micro-fiber
cleaning pad immediately after you
have unplugged and allowed the
steam mop to cool.
20. When cleaning the steam mop,
unplug the power cord from the
electrical outlet and clean with a
dry or damp cloth. Do not pour
water or use alcohol, benzene or
paint thinner on the unit.
21. Extreme caution should be
exercised when using this
appliance to clean stairs .
22. Never use steam mop without
micro-fiber cleaning pad attached.
23. Keep your work area well lit.
24. Store steam mop indoors in a cool,
dry place.
25. To avoid circuit overload, do not
operate another appliance on the
same socket (circuit) as the steam
cleaner.
26. If an extension cord is absolutely
necessary, an extension cord rated
a minimum of 15 ampere, 14 gage
cord should be used. Cords rated
for less amperage may overheat.
Care should be taken to arrange
cord so that it cannot be pulled or
tripped over.
27 Always unplug and allow the steam
mop to cool before removing or
changing mop heads.
WARNING: Your steam mop
is designed to clean hard floor
surfaces that will withstand high
heat. Do not use on unsealed wood
or unglazed ceramic floors . On
surfaces that have been treated
with wax or some no wax floors,
the sheen may be removed by the
heat and steam action. It is always
recommended to test an isolated
area of the surface to be cleaned
before proceeding. We also
recommend that you check the use
and care instructions from the floor
manufacturer.
ww w.s harkcl ea n. com
This manual covers model number: S3601 11
TECHNICAL SPECIFICATIONS
Voltage: 120V., 60Hz.
Power: 1550 Watts
Water Capacity: 500ml (16.9 oz.)
TOL L F RE E: 1-80 0-79 8-739 8
Contents
Eng lis h
Thank you for
purchasing
®
the Shark
Pro
Steam Pocket
Mop.
Getting Started ......................................................................2
Using Your Steam Mop .......................................................5
Using Your Carpet Glider ...................................................9
®
Care of Your Steam Mop ....................................................10
Troubleshooting Guide ....................................................... 12
Warranty ...................................................................................13
ww w.s harkcl ea n. com
1
Getting Started
When assembling your steam mop there
may be a little water in or around the
water tank. This is because we test all
our steam mops 100% before you buy
them, so you get a quality Shark® Pro
Steam Pocket® Mop.
a
c
b
e
f
d
a Steam Mop Body
b Mop Handle
c All-Purpose Mop Head (1) and
Triangle Mop Head (1)
d Filling Flask
e Two-Sided Micro-Fiber Cleaning Pads
for the All-Purpose Mop Head (2)
and Triangle Mop Head (1)
f (1) 6mm x 54mm Large Screw*
g Carpet Glider
*Phillips or flat head screwdriver can be
used. Screwdriver not included.
g
h
i
j
l
k
m
h Quick Release Swivel Cord Wrap
i Cord Clips
j Water Tank Cap
k Water Tank
l ON/Standby Switch
m Mop Head Release Button
2
TOL L F RE E: 1-80 0-79 8-739 8
Eng lis h
fig. 1
IMPORTANT: First things first, always
make sure the mop is UNPLUGGED
from the wall when not in use.
Never fill the mop, attach the mop
head, change or remove the microfiber cleaning pad when the mop is
plugged into the wall. To prolong
the life of your Shark® Pro Steam
Pocket® Mop, we recommend using
distilled water. Make sure you only
add water to the tank. Chemicals or
cleaning solution may damage the
appliance and could be unsafe for
you and your family.
ASSEMBLE
1 Insert the Mop handle end labeled
“Front ” into the steam mop body.
Make sure it is inserted past the
line printed on the pole. Secure the
assembled handle and pole by using
the large screw and a Phillips or a flat
head screwdriver (screwdriver not
included). (fig. 1)
ww w.s harkcl ea n. com
3
Getting Started - cont’d
fig. 2
fig. 3
2 Use the lavender loop on the side of
the micro-fiber cleaning pad to slide
mop head into pad pocket. Then
secure the quick fasteners on the top
of the pocket to lock in place.
(fig. 2)
3 Snap the mop head into the base to
secure it. (fig. 3)
4 Turn the water tank cap counter
clockwise and remove from the tank.
(fig. 4)
Use the filling flask and pour water
into the tank. Please don’t over fill.
Replace the cap on the water tank.
(fig. 5)
fig. 4
fig. 5
IMPORTANT: Don’t use on unsealed
wood or unglazed ceramic floors.
On surfaces that have been treated
with wax or some no wax floors,
the sheen may be removed by
the heat and steam action. It is
always recommended to test an
isolated area of the surface to be
cleaned before proceeding. We
recommend that you check the use
and care instructions from the floor
manufacturer.
4
TOL L F RE E: 1-80 0-79 8-739 8
Using Your Steam Mop
IMPORTANT: Make sure you don’t
use the mop without attaching a
micro-fiber cleaning pad and adding
water to the tank first. When you are
using the mop for the first time, it
might take longer than the normal 30
seconds to start steaming.
Eng lis h
fig. 7
fig. 6
IMPORTANT: Your Steam Mop needs
water to make steam! Never use your
steam mop without water in the tank.
Sweep or vacuum your floors prior to
cleaning with your Steam Mop.
Visit www.sharkclean.com for other
great quick cleaning products to
complement your Steam Mop, such
as the Shark
®
Navigator
(model NV350).
1 Pull and twist the quick release cord
holder to unwrap the power cord
completely. Plug into a 120-volt
electrical outlet. (fig. 6)
2 The ON/STANDBY switch will
flash blue. If the light does not turn
on, reference the troubleshooting
section on page 12. (fig. 7)
ww w.s harkcl ea n. com
5
Using Your Steam Mop - cont’d
fig. 9
fig. 8
3 Press the ON/STANDBY switch once
for dust setting (DUST lighted setting
indicator will illuminate). DUST setting
is light steam for a quick dusting and
best dry time. (fig. 8)
MOP setting is for normal, everyday
steam cleaning. (fig. 9)
SCRUB setting is for heavy cleaning
and will leave floors damp.
6
TOL L F RE E: 1-80 0-79 8-739 8
fig. 10
To better understand which steam
setting to use for your cleaning task,
turn to page 7.
4 Clean your floors with a forward and
backward motion. (fig. 10)
Press the ON/STANDBY switch until
the light flashes to stop the steam.
The Shark® Pro Steam Pocket® Mop has three unique steam settings so
you can use the perfect amount of steam for the cleaning task at hand.
See below for tips on when to use each setting.
Setting Ideal for These Surfaces Recommended Usage
Eng lis h
DUST
MOP
SCRUB
Laminate
Bamboo
Hardwood
Marble
Hardwood
Marble
Tile
Stone
Hardwood*
Tile
Stone
Linoleum
Carpet
(with Carpet Glider)
Light Cleaning and Dusting
Loosen and Lift Light Dirt
Sanitize Floors
Basic, everyday cleaning
Remove spots and smaller messes
Clean moderate and heavilytrafficked areas
Sanitize floors
Tough cleaning and removal of
stuck-on messes and stains
Deep clean heavily-trafficked areas
Cut through heavy dirt and grime
Sanitize floors
Freshen area rugs and carpets
* Scrub mode not recommended for continuous cleaning on hardwood
ww w.s harkcl ea n. com
7
Using Your Steam Mop - cont’d
fig. 11
5 When one side of the micro-fiber
cleaning pad gets dirty, just flip the
mop head and you can quickly start
using the other side. (fig. 11)
6 When the water tank is empty, the
steam mop will stop producing
steam. You can refill the water tank
at any time as long as the mop is
unplugged from the outlet. Follow
the instructions from page 4. This
applies to switching the mop heads
or micro-fiber cleaning pad as well.
8
TOL L F RE E: 1-80 0-79 8-739 8
NOTE: Please wait 2-3 minutes for
the Steam Mop to cool off before
removing the mop head or the
micro-fiber cleaning pad. Never leave
the steam mop with a damp/wet
micro-fiber cleaning pad on
any floor.
Using Your Carpet Glider
fig. 12
Eng lis h
The Steam Mop is great for
grooming and freshening
though it won’t clean your
carpet or area rugs.
THE CARPET GLIDER
1 The Carpet Glider can be used with
the all-purpose head to lightly steam
your carpet and area rugs. Just
place the mop head with micro-fiber
cleaning pad attached on top of the
glider. The recommended steam
setting is SCRUB when using the
carpet glider. (fig. 12)
fig. 13
2 Move the steam mop back and
forth across a section of the carpet.
The steam mop won’t clean your
carpeting or areas rugs, but it’s great
for grooming and freshening.
(fig. 13)
ww w.s harkcl ea n. com
9
Care of Your Steam Mop
fig. 14
fig. 15
AFTER USE AND STORAGE
1 When you have finished using the
steam mop, press the ON/STANDBY
switch until the LED light turns
flashing BLUE. This stops the unit
from steaming. Unplug the cord from
the outlet and place the mop into the
upright position. Let the unit cool for
2-3 minutes.
Remove the micro-fiber cleaning pad
by releasing the quick fasteners and
using the lavender loop on the side
of the pocket, avoiding contact with
the hot pad or dirt. (fig. 14)
10
TOL L F RE E: 1-80 0-79 8-739 8
fig. 16
2 Empty the water tank before
storage. Remove the water tank cap
and empty the tank over a sink.
Replace the water cap. (fig. 15)
3 To store the Shark
®
Pro Steam
Pocket® Mop hanging up, first
remove the head (after it has cooled
and the steam has been released)
then hang on a large hook. (fig. 16)
To order additional parts and
accessories, feel free to contact
us at www.SharkClean.com or
call 1-800-798-7398.
fig. 17 fig. 18
Eng lis h
CARE OF YOUR MICRO-FIBER
CLEANING PAD
1 We recommend washing your
micro-fiber cleaning pad separately
from other fabrics to avoid picking
up lint. Only use liquid detergent
(no powder detergent). Don’t use
any fabric softeners or bleach. Line
dry or dry on a low dryer setting.
(fig. 17)
2 If there are loose threads on the
micro-fiber cleaning pad carefully
cut the thread with scissors. Don’t
pull on them or cut at the base.
(fig. 18)
DECALCIFYING YOUR STEAM MOP
Calcium and mineral deposits can
build up and impact the performance
of your steam mop over time.
To extend the life of your product
we recommend that you use
distilled water or Shark®’s
Water Filtration Bottle.
Visit www.SharkClean.com to order.
ww w.s harkcl ea n. com
11
Troubleshooting Guide
PROBLEM POSSIBLE REASONS & SOLUTIONS
The Pro Steam
Pocket® Mop will not
turn-on.
The unit will not
make steam.
The Pro Steam
Pocket® Mop leaves
water on the floor.
The Pro Steam
Pocket® Mop left a
white spot on the
floor.
Floors are cloudy,
streaky or spotty
after steaming.
Your steam mop should be securely plugged into a
120V AC electrical outlet only.
Check your fuse or breaker.
If your unit still does not work, call 1-800-798-7398.
Is there water in the water tank? If not, add water to your
steam mop following instructions on page 4.
If the unit still doesn’t make steam, follow the
decalcification instructions on page 11.
Check to see if your micro-fiber cleaning pad is soaked
through. We recommend you unplug the steam mop and
change the micro-fiber cleaning pad.
Make sure the micro-fiber cleaning pad is attached
correctly.
Do not leave your steam mop on the floor with a damp or
wet cleaning pad.
If you’re using tap water we recommend switching
to distilled water.
Make sure the cap is securely on the water tank.
The pad might be dirty, change the pad.
If you washed the cleaning pad with powder detergent,
then it might be ruined. Replacement pads are available at
sharkclean.com.
You might have left the mop in the same spot for too long.
Do you have hard water? If you do, you might want to
switch to distilled water.
This might be leftover from past cleaners used on the floor
surface. Use the steam mop a few more times and see if
the leftover cloudiness is removed. If this does not work, we
suggest rinsing the floor with water, letting it dry, and then
steam mopping again with a clean pad. One or more rinses
generally removes the residue. A more stubborn case may
require you to rinse the floor with a mix of one part vinegar
and two parts water.
The Pro Steam
Pocket® Mop is
hard to push.
12
TOL L F RE E: 1-80 0-79 8-739 8
Make sure the micro-fiber cleaning pad is attached
correctly.
Check to see if the cleaning pad is excessively dirty.
Replace if the cleaning pad is too dirty or wet.
Eng lis h
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of the original purchase, when utilized for
normal household use, subject to the following conditions, exclusions and exceptions.
If your appliance fails to operate properly while in use under normal household conditions
within the warranty period, return the complete appliance and accessories, freight prepaid. For
Customer Service support, call 1 (800) 798-7398 or visit our website www.sharkclean.com.
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC
will repair or replace it free of charge. Proof of purchase date and $ 9.95 to cover the cost of
return shipping and handling must be included. *
The liability of EURO -PRO Operating LLC is limited solely to the cost of the repair or
replacement of the unit at our option. This warranty does not cover normal wear of parts and
does not apply to any unit that has been tampered with or used for commercial purposes. This
limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage
due to faulty packaging or mishandling in transit. This warranty does not cover damage or
defects caused by or resulting from damages from shipping or repairs, service or alterations to
the product or any of its parts, which have been performed by a repair person not authorized by
EURO-PRO Operating LLC.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/
or conventional warranties. The responsibility of EURO-PRO Operating LLC warranty if any,
is limited to the specific obligations expressly assumed by it under the terms of the limited
warranty. In no event is EURO- PRO Operating LLC liable for incidental or consequential
damages of any nature whatsoever. Some states/provinces do not permit the exclusion or
limitation of incidental or consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state or province to province.
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of
purchase date and to attach tag to item before packing with your name, complete address and
phone number with a note giving purchase information, model number and what you believe
is the problem with the item. We recommend you insure the package (as damage in shipping
is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER
SERVICE”. We are constantly striving to improve our products, therefore the specifications
contained herein are subjec t to change without notice.
OWNERSHIP REGISTRATION CARD FOR
CANADIAN CONSUMERS ONLY
Please complete and return within ten (10) days of purchase. The registration will enable
us to contact you in the event a product defect is discovered. By returning this card you
acknowledge to have read and understood the instructions for use, and warnings set
forth in the accompanying instructions.
RETURN TO: EURO- PRO Operating LLC, 4400 Bois Franc, St. Laurent, Quebec H4S 1A7
PURCHASER: ……………………………………………………………………………………............................………............
ADDRESS: ………………………………………………………………………………………………...........................................
DATE OF PURCHASE: ………………….........….. MODEL: ……………….....................................................
NAME AND ADDRESS OF STORE: …………………………………...........................………………………………..
S3601 11
ww w.s harkcl ea n. com
13
U. S. : EUR O- PR O Op era tin g LL C
New ton , M A 024 59
Ca nad a: EU RO -P RO O pe rati ng L LC
44 00 B oi s Fra nc
Vil le S t. L au ren t, Q ué bec H4S 1A7
1- 80 0-79 8-73 98
ww w.s har kcl ean .co m
COPY RIGHT© EURO- PRO OP ERATING LLC 201 0
PRI NTED IN CHINA S3601 .E.101 221
Illu strati ons may d iffer from ac tual pro duct.
Loading...