LIGHT & EASY™STEAM MOP
S3255UK
OWNER’S GUIDE
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WHEN USING YOUR SHARK® STEAM MOP,
BASIC SAFETY PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED, INCLUDING THE
FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING
YOUR SHARK® STEAM MOP.
WARNING: DANGER OF SCALDING.
Please use caution when using the steam
mop. The steam emitted from the steam
mop is very hot.
IMPORTA NT:
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety. Children should
be surpervised to ensure that they do not play
with the appliance.
Children shall not use or play with this
appliance. Close supervision is necessary to
keep appliance out of reach of children during
use.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR INJURY:
1 Use the system only for its intended use.
2 DO NOT use outdoors.
3 DO NOT leave the appliance unattended when
plugged in. The plug must be removed from the
socket-outlet before cleaning or maintaining the
appliance.
4 DO NOT allow the appliance to be used by children.
Close attention is necessary when used near
children, pets or plants.
5 Use only as described in this manual.
6 Use only manufacturer’s recommended accessories.
7 If the supply cord is damaged, it must be replaced
by SharkNinja Operating LLC, or its service agent, in
order to avoid a hazard.
8 DO NOT USE if the appliance is not working, has
been dropped, dropped into water, damaged,
leaking or left outdoors.
9 NO SERVICEABLE PARTS. Incorrect re-assembly
or repair can cause a risk of electrical shock or injury
to persons when the appliance is used. Contact
Customer Service.
10 To protect against a risk of electric shock, DO NOT
immerse the steam mop into water or any other liquids.
11 DO NOT handle plug or steam mop with wet hands
or operate appliance without shoes.
12 DO NOT pull or carry by power cord, use power cord
as handle, close a door on the power cord, or pull
the power cord around sharp edges or corners. Keep
power cord away from heated surfaces.
13 DO NOT unplug by pulling on power cord. To unplug,
grasp the plug not the power cord. Do not use
extension cords or outlets with inadequate current
carrying capacity.
1 080 0 862 0 453
14 DO NOT put any objects into openings. Do not use
with any opening that is blocked.
15 DO NOT put hands or feet under the steam mop. Unit
gets very hot.
16 Use ONLY on flat, horizontal surfaces. Do not use on
walls, counters or windows.
17 DO NOT use on leather, wax polished furniture or
floors, synthetic fabrics, velvet or other delicate,
steam sensitive materials.
18 Liquid or steam must not be directed towards
equipment containing electrical components, such as
the interior of ovens.
19 DO NOT add cleaning solutions, scented perfumes,
oils or any other chemicals to the water used in this
appliance as this may damage the unit or make it
unsafe for use. If you live in a hard water area, we
recommend using distilled water in your steam mop.
20 When in use, NEVER turn the appliance over or
on its side. NEVER DIRECT STEAM TOWARDS
PEOPLE, ANIMALS OR PLANTS.
21 NEVER LEAVE THE STEAM MOP IN ONE SPOT
ON ANY SURFACE FOR ANY PERIOD OF TIME
WHEN THE DIRT GRIP
ATTACHED AS THIS WILL DAMAGE YOUR
FLOORS.
22 The steam mop has to be unplugged after use.
23 When cleaning the steam mop, unplug the power
cord from the electrical outlet and clean with a dry
or damp cloth. Do not pour water or use alcohol,
benzene or paint thinner on the unit.
24 Extreme caution should be exercised when using this
appliance to clean stairs.
25 Never use steam mop without the Dirt Grip
Pad attached.
26 Keep your work area well lit.
27 Store steam mop indoors in a cool, dry place.
™
TRIANGLE PAD IS
™
Triangle
28 To avoid circuit overload, do not operate another
appliance on the same mains circuit as the steam
cleaner.
29 If an extension cord is absolutely necessary, an
extension cord rated a minimum of 6 Amperes, with
a minimum of 0.75 mm² copper conductors shall be
used. Cords rated for less amperage may overheat.
Care should be taken to arrange cord so that it
cannot be pulled or tripped over.
30 DO NOT leave unattended when the system is
connected to a power supply or electrical outlet. Turn
off all controls before unplugging the unit.
™
31 DO NOT store unit with damp or wet Dirt Grip
Triangle Pad attached. Never leave the steam mop in
one spot on any surface for any period of time with a
damp or wet Dirt Grip™ Triangle Pad attached as this
will damage your floors.
32 Always unplug and allow the steam mop to cool
before removing or changing mop heads.
33 Make sure that the water tank door is closed when
using the appliance.
WARNING: Your steam mop is designed
to clean hard floor surfaces that will withstand high
heat. Do not use on unsealed wood or unglazed
ceramic floors. On surfaces that have been treated
with wax or some no wax floors, the sheen may
be removed by the heat and steam action. It is
always recommended to test an isolated area of
the surface to be cleaned before proceeding. We
also recommend that you check the use and care
instructions from the floor manufacturer.
SAVE THESE
INSTRUCTIONS
2sharkclean.eu
This appliance complies with the WEEE-Directive 2012/19/EU on the disposal of electrical and electronic
equipment ( WEEE).
This marking indicates that this product should not be disposed with other household wastes
throughout the EU. To prevent possible harm to the environment or human health from uncontrolled
waste disposal, recycle it responsibly to promote the sustainable reuse of material sources. To return
your used device, please use the return and collection systems or contact the retailer where this
product was purchased. They can take this product for environmental safe recycling.
This appliance complies with the European directives for electromagnetic compatibility (EMC) 2014/30/EU and its
revisions, as well as Low Voltage Directive (LVD) 2014/35/EU and its revisions.
This product has no on/off switch and operates when plugged into the main supply source. Disconnect the plug
from mains after use.
Although the product is not provided with standby mode or off mode, it still fulfills the requirements of 1275/2008/
EC – the directive for Eco-Design requirements – since according to technical justification, it is considered as
inappropriate to provide standby and off modes when connecting to the mains. To reduce energy consumption be
sure to unplug the unit after use.
THIS BOOK COVERS MODEL NUMBER:
S3255UK
TECHNICAL SPECIFICATIONS
Voltage: 220-240V~, 50-60Hz
Power: 1050W
Water Capacity: 250 ml (8 oz.)
3 080 0 862 0 453
IPX4
Contents
Thank you for
purchasing the
Shark® Light &
Easy™ Steam
Mop.
Getting Started ..................................................................................................... 5
Using Your Light & Easy™ Steam Mop ..................................................................... 8
Care of Your Light & Easy™ Steam Mop ................................................................ 10
Troubleshooting .................................................................................................. 12
Warranty ............................................................................................................ 14
4sharkclean.eu
Getting Started
When assembling your steam mop there may be a little water in or around the water tank. This is because we test all
our steam mops 100% before you buy them, so you get a quality Shark
®
Light & Easy™ Steam Mop.
a
b
b
c
d
FIRST THINGS FIRST, YOU NEED TO KNOW WHAT’S IN THE BOX YOU JUST OPENED:
a Handle & Extension Tube (Telescopic)
b Steam Mop Base
c Dirt Grip
d Filling Flask
™
Triangle Pad (x2)
5 080 0 862 0 453
fig. 1
fig. 2
ASSEMBLY
1 Remove all the parts from the package. Verify all the
listed parts are included.
2 Insert the assembled handle piece into the steam
mop base. Push the tube base into mop body until
you hear a click. (fig. 1)
3 For your comfort, you can adjust the height of the
mop. Just lift the latch on the tube 90 degrees to the
open position. Holding the handle, extend the tube
to the desired height and then close the latch to the
locked position. (fig. 2)
IMPORTANT: Never use the Light & Easy™
Steam Mop without attaching a Dirt Grip™
Triangle Pad to avoid damage to your floor and
mop.
IMPORTANT: Do not use on unsealed wood
or unglazed ceramic floors.
On surfaces that
have been treated with wax or some no wax
floors, the sheen may be removed by the heat
and steam action. It is always recommended
to test an isolated area of the surface to be
cleaned before proceeding. We recommend
that you check the use and care instructions
from the floor manufacturer.
6sharkclean.eu
Getting Started
fig. 3
ATTACHING THE DIRT GRIP™ TRIANGLE
PAD
1 Place the Dirt Grip™ Triangle Pad on the floor with
the quick fastener strips facing up. Place the Light
& Easy™ Steam Mop on the top of the Dirt Grip™
Triangle Pad to attach. (fig. 3)
IMPORTANT: Only add water to the tank.
Chemicals or cleaning solutions may be
unsafe or cause damage.
IMPORTANT: Please wait 3-5 minutes for your
Light & Easy
removing the Dirt Grip™ Triangle Pad.
7 080 0 862 0 453
™
Steam Mop to cool of f before
fig. 4
FILLING THE WATER TANK
IMPORTANT: Unplug the Light & Easy™ Steam
Mop before filling the water tank with water.
1 Remove the water tank cap by turning it counter-
clockwise to the unlocked position. (fig. 4)
2 A filling flask is included with your Light & Easy
Steam Mop to make filling the water tank easy. Fill
the flask with water and pour it into the tank. Keep
the water level under the MA X’ fill line.
3 Replace the water tank cap and turn it clockwise to
the locked position.
™
Using Your Light & Easy™ Steam Mop
fig. 5
fig. 6
IMPORTANT: Your steam mop needs water
to make steam! Never use your steam mop
without water in the tank.
Sweep or vacuum your floors prior to cleaning with
your Light & Easy
™
Steam Mop.
1
Pull and twist the quick release cord holder to
unwrap the power cord completely. (fig. 5) Plug into
a 220-240 volt electrical outlet. The “On” light will
turn blue. If the light does not turn on, reference the
troubleshooting section on page 12. (fig. 6)
8sharkclean.eu
Using Your Light & Easy™ Steam Mop - cont.
fig. 7
2 Wait 30 seconds for the boiler to heat the water.
Pump the handle a few times to prime the pump,
activate steam and moisten the Dirt Grip™ Trian gl e
Pad. (fig. 7)
3 Mop with a forward and backward motion to
customize steam output automatically. (fig. 8)
IMPORTANT: Never leave the Light & Easy
™
Steam Mop with a damp/wet Dirt Grip™
Triangle Pad on any floor surface for any
amount of time as this may damage the floor.
9 080 0 862 0 453
fig. 8
4 When you need an extra burst of steam to clean
a stuck-on stain, you can use the Steam Blaster™
feature. Lower the mop body forward, toward the
mop head. This will cause the the Steam Blaster
to emit a concentrated blast of steam. To stop the
Steam Blaster spray, simply raise the handle into
its original position and continue cleaning.
CAUTION: While in Steam Blaster mode, do not
leave stationary for more than one minute.
CAUTION: Do not scrub any one area for an
extended period of time.
Care of Your Light & Easy™ Steam Mop
fig. 9 fig. 10
AFTER USE AND STORAGE
1 When you have finished using the Light & Easy™
Steam Mop, unplug the cord from the outlet and
place the mop into the upright position and let the
unit cool 3-5 minutes. Release steam by pumping
the handle several times.
2 Carefully separate Dirt Grip
steam mop, avoiding contact with the hot Dirt Grip™
Triangle Pad or dirt. (fig. 9)
3 Empty the water tank before storage. Remove the
water tank cap and empty the tank over a sink.
Replace the water cap.
™
Triangle Pad from
4 To store the cooled Shark® Light & Easy™ Steam
Mop, hang on a large hook. (fig. 10)
NOTE: If you want to store the Light & Easy
™
Steam
Mop standing upright, make sure it is leaning
against a wall for added support and safety. Always
store your Shark® Light & Easy™ Steam Mop with
the Dirt Grip™ Triangle Pad removed. Store away
from children and high traffic areas.
10sharkclean.eu
Care of Your Light & Easy™ Steam Mop
fig. 11
40°
CARE OF YOUR DIRT GRIP™ TRIANGLE PAD
IMPORTANT: The Dirt Grip™ Triangle Pad may
be very hot from the steam. Use caution when
removing. Let the unit cool for 2-3 minutes.
Care
Machine-wash the Dirt Grip pads separately with warm
water using liquid detergent.
NEVER USE BLEACH, POWDERED DETERGENT, OR
FABRIC SOFTENERS as they may damage or leave
a coating on the Dirt Grip pads that will reduce their
cleaning performance and absorbency. Dirt Grip pads
should be line-dried or tumble-dried on a low setting, as
this will extend the life of the microfibre fabric ( fig. 11).
Loose fibres can indicate wearing of the microfibre
fabric. Do not pull the loose fibres, as this can cause the
weave to come undone. Simply trim the loose fibres with
scissors (fig. 12).
fig. 12
Replacement Dirt Grip pads
For best cleaning results, we recommend replacing your
Dirt Grip pads every 3 to 4 months following normal use.
As with any fabric, dirt particles, grease, friction, and
repeated washing can cause the fibres to break down,
and you may notice an increase in the effort needed to
push or pull the Steam Mop.
11 080 0 862 0 453
Trouble Shooting
PROBLEM POSSIBLE REASONS & SOLUTIONS
The Light & Easy™ Steam Mop
will not turn-on.
Light & Easy
™
Steam Mop
will
not make steam.
Light & Easy
Steam Mop
™
leaves water on the floor.
Light & Easy
Steam Mop
left
™
white spot on the floor.
Floors are cloudy, streaky or
spotty after steaming.
Your steam mop should be securely plugged into an electrical outlet only.
Check the Mains fuse or circuit breaker.
Is there water in the water tank? If not, add water to your steam mop following
instructions on page 7.
Check to see if your Dirt Grip™ Triangle Pad is too wet. We recommend you
unplug the steam mop and change the Dirt Grip™ Triangle Pad.
Make sure the Dirt Grip
™
Triangle Pad is attached correctly.
Do not leave your steam mop on the floor with a damp or wet Dirt Grip™
Triangle Pad.
If you’re using tap water, we recommend switching to distilled water.
Make sure the cap is secured on the water tank.
The Dirt Grip™ Triangle Pad might be dirty. Change the Dirt Grip™ Triangle Pad.
If you washed the Dirt Grip™ Triangle Pad with powder detergent, then your Dirt
Grip™ Triangle Pad could be damaged and require replacement.
This could also be an indication of prior soap or grease residue that has
accumulated on the floor. As our steam mops use only a small amount of
water, it may not be wet enough to rinse off the accumulation that the steam
is bringing to the surface. We suggest rinsing the floor with nothing but water,
letting it dry, and then steam mopping again with a clean Dirt Grip
™
Triangle
Pad. One or more rinses generally removes the residue.
A more stubborn case may require you to rinse the floor with a mix of one part
vinegar and two parts water.
Light & Easy
hard to push.
™
Steam Mop
Make sure the steam Dirt Grip™ Triangle Pad is attached correctly.
is
Check to see if the Dirt Grip™ Triangle Pad is excessively dirty. Replace if the
Dirt Grip™ Triangle Pad is too dirty or wet.
12sharkclean.eu
Notes
13 080 0 862 0 453
Warranty Terms and Conditions
When a consumer buys a product in the UK, they get the benefit of legal rights relating to the quality of the product (your
“statutory rights”). You can enforce these rights against your retailer. However, at Shark we are so confident about the quality of
our products that we give you an additional manufacturer’s warranty of up to two years upon registration with Shark. Offer valid
only in United Kingdom and Republic of Ireland. These terms and conditions relate to our manufacturer’s warranty only – your
statutory rights are unaffected.
The conditions below describe the prerequisites and scope of our warranty. They do not affect your statutory rights or the
obligations of your retailer and your contract with them.
®
Shark
Guarantees
A household appliance like a steam mop constitutes a sizeable investment. Your new machine needs to work properly for as long
as possible. The guarantee it comes with is an important consideration - and reflects how much confidence the manufacturer
has in its product and manufacturing quality.
Every Shark
from 9.00am to 6.00pm Monday - Friday. It’s free to call, and you’ll be put straight through to a Shark representative. You’ll also
find online support at www.sharkclean.eu/uk.
How do I register my extended Shark
You can register your guarantee online within 28 days of purchase. To save time, you’ll need the following information about your
machine:
• Date you purchased the machine (receipt or delivery note)
• To register online, please visit www.sharkclean.eu/uk/register-guarantee
IMPORTANT
• Both the 12 months and the extended 1 year guarantee will only cover your product from the date of purchase.
• Please keep your receipt at all times. Should you need to use your extended guarantee we will need your receipt to verify the
What are the benefits of registering my free Shark
When you register your guarantee we’ll have your details to hand if we ever need to get in touch. You can also receive tips
and advice on how to get the best out of your Shark
launches.
If you register your guarantee online, you’ll get instant confirmation that we’ve received your details.
How long are new Shark
Our confidence in our design and quality control means that your new Shark
(12 months plus an extended warranty of 1 year).
What is covered by the free Shark
Repair or replacement of your Shark
addition to your legal rights as a consumer.
What is not covered by the free Shark
• Blockages – For details of how to unblock your steam mop, please refer to the Operating Manual.
• Normal wear and tear.
• Accidental damage, faults caused by negligent use or care, misuse, neglect, careless operation or handling of the steam
• Use of the steam mop for anything other than normal domestic household purposes.
• Use of parts not assembled or installed in accordance with the operating instructions.
• Use of parts and accessories which are not Shark
• Faulty installation (except where installed by Shark
• Repairs or alterations carried out by parties other than Shark or its agents.
What happens when my guarantee runs out?
Shark
want to repair their steam mops after the warranty has elapsed. In this case please contact our free phone customer service help
line and ask about our out warranty program, on 0800 862 0453.
Where can I buy genuine Shark
Shark
range of Shark
www.sharkclean.eu/uk/accessories. Please remember that using non-Shark
®
machine comes with a free parts and labour guarantee. Our customer service helpline (0800 862 0453) is open
®
guarantee?
information you have supplied to us is correct. The inability to produce a valid receipt may invalidate your guarantee.
®
guarantee?
®
steam mop and hear the latest news about new Shark® technology and
®
machines guaranteed for?
®
guarantee?
®
machine (at Shark®’s discretion), including all parts and labour. A Shark® guarantee is in
®
guarantee?
mop which is not in accordance with the Shark
®
does not design products to last for a limited time. We do appreciate that there may be a desire for our customers to
®
®
spares and accessories are developed by the same engineers who developed your Shark® steam mop. You’ll find a full
®
spares and replacement parts for all Shark® machines at www.sharkclean.eu/uk/parts. Accessories are at
spares and accessories?
®
Operating Manual supplied with your machine.
®
Genuine Components.
®
).
®
steam mop is guaranteed for a total of two years.
®
spares invalidates your guarantee.
14sharkclean.eu
Euro-Pro Europe Limited
15 Mariner Court
Calder Park
Wakefield
WF4 3FL
Freephone 0800 862 0453
www.sharkclean.eu
Shark is a registered trademark of
SharkNinja Operating LLC.
Dirt Grip and Light & Easy are trademarks of Shark Ninja
Operating LLC.
COPY RIGHT © SH ARKNINJA OPERATING LLC 2017
Illustrations may differ from actual product. We are
constantly striving to improve our products, therefore the
specifications contained herein are subject to change
without notice.
PRINTED IN CHINA
S3 255 U K _ IB_170 207
IPX4
Loading...