Shark Rotator Powered Lift-Away NV750 Series, Rotator Powered Lift-Away NV650 Series Owner's Manual
Rotator®
Powered Lift-Away
®
Upright Vacuum
Aspirateur vertical
Aspiradora vertical
NV650/750
Series • Série • Serie
OWNER’S GUIDE
GUIDE D’UTILISATION
MANUAL DEL PROPIETARIO
sharkclean.com
IMPORTANT SAFETY INSTRUCTIONS
FOR HOUSEHOLD USE ONLY • PLEASE READ CAREFULLY BEFORE USE
If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. DO NOT force into outlet or try to modify to fit.
WARNING
To reduce the risk of fire, electric shock, injury, or property damage:
GENERAL WARNINGS
1. Your vacuum cleaner may consist of
a motorized nozzle, wand, hose, and/
or vacuum pod. This device contains
electrical connections, electrical
wiring, and moving parts that
potentially present risk to the user.
2. Use only identical replacement parts.
3.
Carefully observe and follow the
instructions provided below to avoid
improper use of the appliance. DO NOT
use the vacuum for any purpose other
than those described in this manual.
4. Before use, carefully inspect all parts
for any damage. DO NOT use if any
parts are damaged.
5. The use of an extension cord is
NOT recommended.
6. This vacuum cleaner contains no
serviceable parts.
USE WARNINGS
7. DO NOT allow the appliance to be
used by children. Close supervision is
necessary when used near children.
This is not a toy.
8. Always turn off the vacuum cleaner
before connecting or disconnecting
any motorized nozzles or other
accessories.
9. DO NOT handle plug or vacuum
cleaner with wet hands.
10. DO NOT use without filters in place.
11. Only use Shark® branded filters
and accessories. Failure to do so
will also void the warranty.
12. DO NOT damage the power cord:
a) DO NOT pull or carry vacuum
cleaner by the cord or use the
cord as a handle.
b) DO NOT unplug by pulling on
cord. Grasp the plug, not the cord.
c) DO NOT run the vacuum cleaner
over the power cord, close a door
on the cord, pull the cord around
sharp corners, or leave the cord
near heated surfaces.
13. DO NOT put any objects into nozzle
or accessory openings. DO NOT use
with any opening blocked; keep free
of dust, lint, hair, and anything that
may reduce airflow.
14. DO NOT use if nozzle or accessory
airflow is restricted. If the air paths or
the motorized floor nozzle become
blocked, turn the vacuum cleaner
off and unplug from electrical outlet.
Remove all obstructions before you
plug in and turn on the unit again.
15. Keep nozzle and all vacuum
openings away from hair, face,
fingers, uncovered feet, or loose
clothing.
16. DO NOT use if vacuum cleaner is
not working as it should, or has been
dropped, damaged, left outdoors, or
dropped into water.
sharkclean.com
17. Use extra care when cleaning
on stairs.
18. DO NOT leave the vacuum cleaner
unattended while plugged in.
19. When powered on, keep the vacuum
cleaner moving over the carpet surface
at all times to avoid damaging the
carpet fibers.
20. DO NOT place vacuum cleaner
on unstable surfaces such as chairs
or tables.
21. Your Shark® vacuum may not be
designed to stand up on its own. When
taking a break from cleaning, you may
need to lean it against furniture or a
wall, or lay it flat on the floor. Using
the vacuum for an application where
the unit lacks stability may result in
personal injury.
22. DO NOT use to pick up:
a) Liquids
b) Large objects
c) Hard or sharp objects
(glass, nails, screws, or coins)
d) Large quantities of dust (drywall
dust, fireplace ash, or embers).
DO NOT use as an attachment to
power tools for dust collection.
e) Smoking or burning objects
(hot coals, cigarette butts,
or matches)
f) Flammable or combustible
materials (lighter fluid, gasoline,
or kerosene)
g) Toxic materials (chlorine bleach,
ammonia, or drain cleaner)
23. DO NOT use in the following areas:
a) Poorly lit areas
b) Wet or damp surfaces
c) Outdoor areas
d) Spaces that are enclosed and may
24. Turn off all controls before plugging in
25. Unplug from electrical outlet
26. Hand wash with water only.
27. During cleaning or routine
28. Allow all filters to air-dry completely
29. Make sure the dust cup and all filters
30. If provided, secure the power
contain explosive or toxic fumes
or vapors (lighter fluid, gasoline,
kerosene, paint, paint thinners,
mothproofing substances, or
flammable dust)
or unplugging the vacuum.
when not in use and before
any maintenance or cleaning.
Washing with cleaning chemicals
could damage the unit.
maintenance, DO NOT cut anything
other than hair, fibers, or string
wrapped around the brushroll.
before replacing in the vacuum to
prevent liquid from being drawn
into electric parts.
are in place after routine maintenance.
cord around the two cord hooks
during storage.
To reduce the risk of electric shock, this appliance has a polarized plug (one blade
is wider than the other). This plug will fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install the proper outlet. Do not change the plug in any way.
SAVE THESE INSTRUCTIONS
sharkclean.com
2
(Click)
ASSEMBLY
3
(Click)
1
(Click)
1. Insert Wand into Floor Nozzle.
2. Insert Handle into wand.
3. Place Pod onto wand and slide down to connect.
4. Connect Hose into back of pod, until it clicks into place.
For proper operation, ensure all parts are firmly clicked into place.
sharkclean.com
ASSEMBLY
4
(Click)
sharkclean.com
WHOLE-HOME CLEANING
SETTINGS
Choose the appropriate setting.
Thick Carpet/Area Rug Cleaning
Set floor selector to Carpet.
Carpet/Low Pile Cleaning
Set floor selector to Carpet/Low Pile.
Hard Floor Cleaning
Set floor selector to Hard Floor.
NOTE: For deep cleaning per ASTM F 608 (embedded dirt
in carpets) please set to Carpet/Low Pile.
BRUSHROLL INDICATOR LIGHT
WHAT DOES THE BRUSHROLL INDICATOR
LIGHT MEAN?
Solid Green: The brushroll is spinning and
working as it should.
Solid Red: There is a jam in the brushroll
area. Turn your vacuum o and remove
any blockages.
Flashing Red*: The motorized floor nozzle is
overheating. Turn your vacuum o and wait
for it to cool down.
No Light: The brushroll is o because the
vacuum is in Hard Floormode.
* See Troubleshooting section for further
instructions.
INDICATOR LIGHT
sharkclean.com
WHOLE-HOME CLEANING
CLEANING MODES
UPRIGHT LIFT-AWAY®
To engage brushroll, turn power on, select
a surface setting, then place foot on floor
nozzle and tilt handle back.
L
i
f
t
A
w
a
y
®
Press Lift-Away button to lift pod o
motorized floor nozzle. You are now ready
to clean those hard-to-reach places. Attach
cleaning tools directly to the handle or to the
wand for extended reach.
Handle
ABOVE-FLOOR ABOVE-FLOOR—EXTENDED REACH
Press the Handle button to detach the
handle to clean above-floor areas or with
attachments. Insert cleaning tools directly
into wand orhandle.
Wand
Release
Press the Wand Release button to detach
the wand to clean with more reach. Insert
cleaning tools directly into wand orhandle.
sharkclean.com
AVAILABLE ACCESSORIES
11” Crevice Tool
A
This slim tool is great for cleaning in tight
spaces, between couch cushions, and in
hard-to-reach areas.
A
B
Upholstery Tool
Perfect for large-particle pickup, dusting,
and removing stubborn pet hair and lint
from furniture and other upholstered
surfaces.
Dusting Brush
C
This brush dusts and cleans delicate
surfaces. Great for use on fans, blinds,
lampshades, and keyboards.
Duster Crevice Tool
D
Two cleaning tools in one: the crevice tool
gives you extended reach to clean in tight
spaces, while the soft brush lets you dust
delicate surfaces.
Dust-Away™ Hard Floor Attachment
E
Durable enough for cleaning big crumbs
and debris but gentle enough for delicate
dusting on hardwood and tile floors.
B
C
D
E
Canister Caddy
F
Transforms your Rotator® into a canister
vacuum, giving you the freedom to roll the
pod along while keeping cleaning tools
close by.
NOTE: Not all accessories come with all units. Please see the enclosed Quick Start Guide for your unit's
configuration. To order additional accessories, visit sharkaccessories.com.
F
sharkclean.com
EMPTYING THE DUST CUP
IMPORTANT: Unplug the power cord before performing any maintenance.
Pull up on Dust Cup, release latch and lift dust
cup o pod
Press top dust cup release latch to access
dust screen and remove built-up debris as
necessary.
Hold dust cup over a trash bin and press the
empty-release latch on the bottom to empty
dust and debris into trash.
sharkclean.com
CLEANING AND REPLACING THE FILTERS
CLEANING FILTERS
Regularly clean and replace your filters to keep your vacuum's suction power optimal.
To clean filters, rinse with cold water ON LY to prevent damage from cleaning chemicals. Allow
all filters to air-dry for at least 24 hours before reinstalling them to prevent liquid from being
drawn into electricparts.
IMPORTANT: DO NOT use soap when cleaning the filters.
Foam Filter
Filter Access
Filter Frame
Felt Filter
HEPA
Pre-Motor (foam and felt):
With the dust cup removed, take out and
rinse the foam and felt filters with water.
Tap loose dirt o filters between washes
asneeded.
Post-Motor (HEPA):
To access the HE PA Filter, pull the latch
under the filter cover and take o the cover.
Take out the HEPA filter and rinse it.
CLEAN HEPA FILTER EVERY YEAR.
CLEAN PRE-MOTOR FILTERS EVERY
3 MONTHS.
REPLACING FILTERS
Follow the previous instructions for removing filters. The pre-motor filters should be replaced every
2.5 years. The post-motor HEPA filter should be replaced every 3 years.
Replacement
Pre-Motor Foam &
Felt Filter Kit
Replacement
HEPA Filter
XHF650
XFF650
NOTE: To order replacement parts and filters, visit sharkaccessories.com.
sharkclean.com
CHECKING FOR BLOCKAGES & MAINTAINING BRUSHROLL
Use the edge of a coin to open the
3 locks on the bottom of the floornozzle.
With scissors, carefully cut along the
groove in the brushroll to remove any
debris, hair, or fibers.
Lift up the lid on the bottom of the
nozzle to access the brushroll. Use
a flashlight to check for blockages.
To reinstall the lid, line it up along the
front of the nozzle and press it closed.
Use the coin to close the 3 locks.
sharkclean.com
TROUBLESHOOTING
PROBLEM POSSIBLE REASONS & SOLUTIONS
Check filters to see if they need cleaning. Follow instructions for
rinsing and drying the filters before reinstalling.
Vacuum is not picking
up dirt. No suction or
light suction.
Vacuum lifts area rugs
.
Brushroll does not spin.
Vacuum turns o on its own,
or indicator light flashes red.
Dust cup may be full; empty dust cup.
Check hoses, hose connections, nozzle, and accessories for
blockages; clear blockages if required.
Remove any string, carpet fibers, or hair that may be wrapped
around the brushroll.
Turn o unit to disengage the brushroll. Move switch to Hard Floor
setting for suction-only cleaning, and turn unit back on.
Suction is powerful. Take care when vacuuming area rugs or rugs
with delicately sewn edges.
If Brushroll Indicator Light on the motorized floor nozzle turns red,
the brushroll has stopped spinning. Immediately turn o and unplug
vacuum, disconnect the nozzle, and remove any blockages before
reconnecting and turning vacuum back on.
With the power on, recline the handle, which will automatically turn
on the brushroll.
Make sure the carpet height selector is NOT set to Hard Floor.
This vacuum is equipped with a motor-protective thermostat. If your
vacuum overheats, the thermostat will automatically turn the suction
motor o. Perform the following steps to restart the thermostat:
1. Turn vacuum o and unplug it.
2. Empty dust cup and clean filters.
3. Check for blockages in hoses, accessories, and inlet openings.
4. Allow unit to cool for a minimum of 45 minutes.
5. Plug in vacuum and turn it on.
If hose is not fully connected to the pod, it can cause a poor electrical
connection and the hose can come loose, turning the vacuum o.
1. Turn vacuum o and unplug it.
2. Empty dust cup and clean filters.
3. Check for blockages in hose, accessories, and inlet openings.
4. Remove cord from cord hook so hose latch can be seen and
engaged.
5. Make sure all parts are securely clicked into place at all
connection points:
a. Where hose meets back of pod (pull on hose to ensure latch
is fully engaged)
b. Where wand plugs into floor nozzle
c. Where handle plugs into wand
6. Plug in vacuum and turn it on.
Note: If vacuum still does not start, contact Customer Service at:
1-800-798-7398.
Loading...