Shark Rotator NV680ANZ User Manual

Download

Page 1

™

Model

NV680ANZ

Page 2

NZ: 08 00 002 99 9

AUST: 180 0 890 840

IMPORTANT SAFEGUARDS

FOR HOUSEHOLD USE ONLY

READ ALL INSTRUCTIONS BEFORE USE

Contents

Getting to Know Your Shark® Rotator™ Powered Lift-Away™ Speed Vacuum ��3 Assembly ��4 Upright Cleaning ��5 What Does the Brushroll Indicator Light Mean? ��5 Above Floor Cleaning� ��6 Powered Lift-Away™ Cleaning ��7 Lift-Away™ Cleaning ��7

Maintenance ��8

Empty the Dust Cup��8 Clean the Filters ��8 Check for Blockages ��9 Trouble-Shooting Guide ��10 Warranty ��14

Thank you for purchasing the Shark®

Rotator™ Powered Lift-Away™ Speed.

IMPORTANT SAFEGUARDS

TECHNICAL SPECIFICATIONS:

Voltage: 220-240V~, 50/60Hz Main Body Motor Watts: 850W Power Nozzle Watts: 80W

GMA-102233-EA-013

GENERAL USE 17 Use only as described in this manual� 18 DO NOT put any objects into openings� DO NOT use with any opening blocked; keep free

of dust, lint, hair, and anything that may reduce air ﬂow�

19 Keep your work area well lit� 20 Keep the vacuum cleaner moving over the carpet surface at all times to avoid damaging

the carpet ﬁbers�

21 DO NOT place vacuum cleaner on unstable surfaces such as chairs or tables� 22 DO NOT use without dust cup and/or ﬁlters in place� 23 DO NOT step on, run over, or bend hose� The hose is powered by electrical wires that may

be damaged as a result�

HOSE ATTACHMENTS

24 DO NOT use if air ﬂow is restricted; if the air paths, the hose, or the accessories become blocked,

turn the vacuum cleaner off� Remove all obstructions before you turn on the unit again�

25 Keep the end of the hose and accessory openings away from face and body� 26 Keep cleaning tools and hose suction openings away from hair, face, ﬁngers, uncovered

feet, or loose clothing�

27 Only use manufacturer’s recommended attachments�

DUST CUP/FILTERS/ACCESSORIES

Before turning on the vacuum:

28 Make sure that all ﬁlters are thoroughly dry after routine cleaning� 29 Make sure that dust cup and all ﬁlters are in place after routine maintenance� 30 Make sure accessories are free of blockages� 31 Use only manufacturer’s recommended accessories and replacement parts�

GENERAL CLEANING 32 DO NOT pick up large-sized objects� 33 DO NOT pick up hard or sharp objects such as glass, nails, screws or coins that could

damage the vacuum cleaner�

34 DO NOT use to pick up drywall dust� 35 DO NOT pick up smoking or burning objects such as hot coals, cigarette butts, ﬁreplace

ash or matches�

36 DO NOT pick up ﬂammable or combustible materials such as lighter ﬂuid, gasoline, or

kerosene or use vacuum in areas where they may be present�

37 DO NOT pick up toxic solutions such as chlorine bleach, ammonia, or drain cleaner� 38 DO NOT use in an enclosed space where vapors are present from paint, paint thinner,

moth-prooﬁng substances, ﬂammable dust or other explosive or toxic materials�

39 DO NOT vacuum up any liquids� 40 DO NOT immerse vacuum cleaner in water or other liquids� 41 DO NOT use outdoors or on wet surfaces; use only on dry surfaces� 42 Use extra care when cleaning on stairs� 43 Remove brushroll from unit before rinsing�

SAVE THESE INSTRUCTIONS

When using an electrical appliance, basic safety precautions should always be observed, including the following:

WARNING

This appliance is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children shall not use or play with this appliance. Close supervision is necessary to keep appliance out of reach of children during use.

CAUTION

THE POWER NOZZLE, WAND, HOSE, AND HANDLE CONTAIN ELECTRICAL CONNECTIONS:

• These are not serviceable parts�

• Do not use to vacuum any liquids�

• Do not immerse in water when cleaning�

• Prior to use, inspect hose, handle/wand for damage� Discontinue using if damaged�

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY: 1 DO NOT use outdoors or on wet surfaces� 2 Unplug from electrical outlet when not in use and before cleaning or servicing� 3 Inspect power cord or plug for any damage before use� DO NOT use vacuum cleaner with a

damaged cord or plug�

4 DO NOT use if the appliance is not working, has been dropped, dropped into water,

damaged or left outdoors�

5 NO SERVICEABLE PARTS� Incorrect re-assembly or repair can cause a risk of electrical

shock or injury to persons when the appliance is used� Contact Customer Service�

6 The hose contains electrical wires� Do not use when damaged, cut or punctured� 7 DO NOT pull or carry vacuum cleaner by the cord or use the cord as a handle� 8 DO NOT unplug by pulling on cord; to unplug, grasp the plug, not the cord� 9 DO NOT handle plug or vacuum cleaner with wet hands� 10 DO NOT run the vacuum cleaner over the power cord, close a door on the cord or pull cord

around sharp corners�

11 The use of an extension cord is not recommended� 12 DO NOT leave vacuum cleaner unattended when plugged in� 13 Keep cord away from heated surfaces� 14 Turn off all controls before plugging or unplugging the vacuum cleaner� 15 Always turn off the vacuum cleaner before connecting or disconnecting power nozzle� 16 Store your vacuum cleaner with the power cord secured around the two cord holders�

Page 3

NZ: 08 00 002 99 9

AUST: 180 0 890 840

ETTI NG TO KNOW YOUR SHARK ROTATOR® POWERED LIFT-AWAY™ SPEED

ASS EMBLY

STEP 1 STEP 2 STEP 3 STEP 4 STEP 5

Pet Power Brush

188FLI680

Designed for removal of pet hair and ground in dirt from carpeted stairs and upholstery�

Dusting Genie/2-in-1 Crevice Tool

189FLI680

Two cleaning tools in one� The crevice tool gives you extended cleaning reach for small spaces, while the dusting brush cleans a multitude of surfaces�

1 Place the selec ted ﬂoor nozzle o n the ﬂoor and inser t

the wand�

2 Insert th e handle into the wan d�

3 Slide the pod onto t he wand�

4 Slide the hose clip into t he notch at the b ack of the

wand�

5 Insert the dus ting genie and pet po wer brush into th e

accessor y posts as show n�

TIP: For quick cord access, r otate upper ho ok down and

remove cord� Rotate back for cord storage�

SLIDE

CLICK

MAIN U NIT 1 Surface Selector 2 Suction Cont rol 3 Hose 4 Hose Clip 5 Upp er Cord Hook 6 Power Switch

7 Wand Release 8 Lift-Away Pod 9 Lo wer Cord Hook 10 Motorized Floor Nozzle 11 Headlights 12 Brushroll Indic ator Light

Wand Release

Page 4

5 6

NZ: 08 00 002 99 9AUST: 180 0 890 840

UPRIGHT CLEANING

WARNING: To reduce the risk of electric shock, unplug the unit before assembling, adding or removing

attachments or converting modes.

WARNING: Always ensure the power is OFF before plugging and unplugging.

NOTE: DO NOT use to pic k up drywall dus t or ﬁreplace ash�

STEP 1 STEP 2 STEP 3

1 Plug in power cord into electrical outlet and press

POWER button to turn vacuum on�

2 Hard Floor Cleaning

Set Floor Selector to Hard Floor and Suction Control

to Max for full suction or variable depending on user preference� Both the motorised ﬂoor nozzle and the Shark Dust Away™ heads can be used on hard ﬂoors�

Thick Carpet & Area Rugs Cleaning

Set Floor Selector to Carpet and Suction Control to

Min for reduced suction or variable depending on user preference�

Carpet Cleaning

Set Floor Selector to Carpet and Suction Control to Max

for full suction or variable depending on user preference�

3 Place your left foot gently on the ﬂoor nozzle and tilt the

handle back to start cleaning� Note: The brushroll will only spin once the vacuum is reclined back�

Suction Control

Floor Selector

MinMax

ABOVE FLOOR CLEANING

NOTE: DO NOT use to pic k up drywall dus t or ﬁreplace ash�

1 For above ﬂoor cl eaning with the ho se, press the WAND

or HANDLE r elease (depending o n the amount of rea ch required) th en lift handle up�

2 Insert wand or h andle directly in to desired tool� 3 This unit is equipped with S UCTION CON TROL to help

when dusting d elicate object s or drapery� Loc ated at base of the han dle, slide the SUCT ION CONTROL t ab to minimize suctio n� Be sure to close agai n for maximum suction�

STEP 1 STEP 2 STEP 3

Wand Release

Suction Control

MinMax

WHAT DOES THE B RUSHROLL INDICATOR L IGHT MEAN?

• Solid G reen: The br ushroll is on and workin g as it should�

• Solid R ed: There is a jam i n the brushroll area� Turn yo ur vacuum off and rem ove the blockage�

• *Flas hing Red: T he motorized ﬂoor n ozzle is overheat ing� Turn your vacuum off a nd wait for it to cool dow n�

*See Troubleshoo ting section for fur ther instruc tions�

Page 5

7 8

NZ: 08 00 002 99 9AUST: 180 0 890 840

RECOMMENDED FILTER CLEANING SCHEDULE:

Pre-motor Filter Kit (Foam & Felt): XFF680 Every 3 months Post Motor Filter: XHF680 Every year

1 Press LIF T-AWAY button to lift the p od off the ﬂoor

nozzle�

Insert the WAND in to the motorize d ﬂoor nozzle�

TIP Using the vacuum in Powered Lift-Away mode gives you

extended reach for cleaning under furniture and in tight spaces�

2 Insert the HANDLE into the motorized ﬂoo r nozzle�

TIP Attaching the HANDLE directly into the nozzles makes

cleaning stairs easy�

1 Attach the desired accessory directly into the HANDLE�

TIP For an extended reach, attach the desired accessory into

the WAND�

POW ERED LIF T-AWAY™ CLEANING LIF T-AWAY™ CLEANING

EMPTY THE DUST CUP

1 Pull up on the dust cup r elease latch and li ft the dust cup

off the pod �

2 Holding the dust cup over a garbage bag or can, press the

bottom empty release latch�

3 Press the top dust cup release latch to access the dust

screen and remove built-up debris as required�

CLEAN THE FILTERS 1 With the dust cup removed, remove and rinse the foam

and felt ﬁlters every 3 months� Let air dry completely before replacing� Hand wash only� Tap loose dirt off ﬁlters between washes as needed�

2 Once a year open t he ﬁlter grill and remo ve and

rinse the HEPA ﬁl ter� Let air dry comp letely before replacing� Hand wash only�

WARNING: D O NOT PICK UP F IREPLAC E ASH OR DRYWA LL DUST.

MAINTENANCE

To keep your vacuum’s suction power optimal, follow these instructions. Make sure uni t is off and cor d unplugged. IMPORTANT: Allow ALL ﬁlters to dry completely before replacing into the vacuum.

STEP 1 STEP 2 STEP 3

HEPA

FELT FILTER

FOAM FILTER

FILTER FRAME

STEP 1 STEP 2

Extension Wand

Page 6

9 10

NZ: 08 00 002 99 9AUST: 180 0 890 840

TROUBLE-SHOOTING GUIDE

Vacuum is not picking up dirt. No suction or light suction • Check ﬁlters to see if they need cleaning� Follow instructions for rinsing and drying the ﬁlters before re-inserting back

into the vacuum�

• Dust cup may be full; empty dust cup�

• Check hose, hose connections, nozzles, and accessories for blockages; clear blockages if required�

• Remove any string, carpet ﬁbers or hair that may be wrapped around the brushroll�

Vacuum lifts area rugs • Turn off the unit to disengage the brushroll and restart with the POWER button for suction only cleaning�

• Suction is powerful� Take care when vacuuming area rugs or rugs with delicately sewn edges�

• Turn off the unit and disengage the area rug from the brushroll and restart the unit�

Brush roll does not spin • If brush roll indicator light on the ﬂoor nozzle turns red, the brush roll has stopped spinning� Immediately turn off and

unplug vacuum, disconnect the nozzle and remove blockage before reconnecting and turning vacuum back on�

• Pull the handle toward you and release the ﬂoor nozzle to disengage the auto-off feature�

• Make sure that the carpet height selector is not on the HARD FLOOR setting�

• Immediately turn off and unplug vacuum, disconnect the nozzle and remove blockage before reconnecting and turning vacuum back on�

Vacuum turns off on its own or indicator l ight ﬂashes red • This vacuum cleaner is equipped with a motor protective thermostat� If for some reason your vacuum overheats, the

thermostat will automatically turn the suction motor off� Should this occur, perform the following steps to restart the thermostat:

1� Turn the unit off� 2� Unplug the vacuum� 3� Empty the dust cup and clean ﬁlters (see page previous page) 4� Check for blockages in hose, accessories and inlet openings� 5� Allow the unit to cool for a minimum of 45 minutes� 6� Plug in the vacuum� 7� Restart the unit by turning the power on� Note: If vacuum still does not start, contact Customer Service at: AUST: 1800 890 840 or NZ: 0800 002 999�

MAINTENANCE

To keep your vacuum’s suction power optimal, follow these instructions. Make sure uni t is off and cor d unplugged.

CHECK FOR BLOCKAGES

1 Use a coin to unlock the 3 locks on the

bottom of the ﬂoor nozzle�

2 A portion of the base is removable to

allow for better access to the brush roll and exposure to the airway� Shine a ﬂashlight from the bottom to check for possible blockage in the airway�

3 Remove any string, carpet ﬁbers or

hair that may be wrapped around the brush roll� There is a groove on the brush bar that allows a pair of scissors to cut across it to loosen up the debris�

4 To reassemble, replace base by

lining it up along the front of the nozzle� Push down to snap into place� Lock the 3 locks�

STEP 1 STEP 2 STEP 4STEP 3

Page 7

11 12

NZ: 08 00 002 99 9

AUST: 180 0 890 840

NOTES NOTES

Page 8

NZ: 08 00 002 99 9

AUST: 180 0 890 840

Shark is a registere d trademark o f SharkNinja Ope rating LLC� Rotator, H ard-Floo r Genie and Lift- Away are trademar ks of SharkNinja O perating LL C�

If your product becomes defective due to faulty material or workmanship within a period of 5 years from the date of purchase, we warrant to do the following:

• For New Zealand Consumers: We will replace the product with a new product, free of charge, or repair the product at our cost, at our discretion�

• For Australian Consumers: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law� You are entitled to a replacement or refund for a major failure

and for compensation for any other reasonably foreseeable loss or damage� You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure�

Your warranty is subject to the following conditions:

• DO NOT operate the appliance with a damaged plug or cord, or if the unit has been dropped, damaged or dropped in water� To avoid the risk of electric shock, do not disassemble or

attempt to repair the appliance on your own� If the supply cord is damaged, it must be replaced by a qualiﬁed electrician in order to avoid a hazard� Incorrect re-assembly or repair can cause a risk of electrical shock or injury to persons when the appliance is used�

• The product has not been misused, abused, neglected, altered, modiﬁed or repaired by anyone�

• The product has been subjected to fair wear and tear�

• The product has not been used for trade, professional or hire purposes�

• The product has not sustained damage through foreign objects, substances or accident�

Your warranty does not cover:

• Components that are subject to natural wear and tear caused by normal use in accordance with operating instructions�

• Unauthorised/improper maintenance/handling or overload is excluded from this warranty�

• For guarantee claims you will need to submit a proof of purchase in the form of a valid receipt that displays date and place of purchase�

This warranty does not replace but is in addition to your statutory rights�

This warranty does not apply to accessories supplied with the product�

This warranty applies only to the original purchaser and may not be transferred�

Replacement products will be covered by the limited warranty for the balance of the warranty period from the date of the original purchase�

Please note:

Only defective product or parts returned to place of purchase will be replaced under this warranty�

New Zealand Contact: Australia Contact

Brand Developers Limited Brand Developers Aust Pty Ltd

Unit H, 686 Rosebank Road, 461 Plummer Street,

Avondale 1026, Auckland, New Zealand PORT MELBOURNE, VIC 3207

FAX: +64 9 306 8203 FAX: +61 3 9681 7825

NZ Customer Care 0800 002 999 AUST Customer Care: 1800 890 840

FIVE (5) YE AR LIMITED REPLACEMENT WARRANT Y STATEMENTNOTES

Page 9

NV680ANZ_IB_E_151020_1

Illust rations may d iffer fro m actual pro duct� We are constantly s triving to

impro ve our produ cts, there fore the spe ciﬁcatio ns containe d herein are

subject to cha nge withou t notice�

Printed in China

GMA-102233-EA-013

Shark Rotator NV680ANZ User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual