Shark NV352, NV351 User Manual
Owner’s guide
Guía del usuario
NV351
NV352
www.sharkclean.com
NV351_26_NV352_26_IM_ENG_SPA_101207.indd 1 10-12-08 9:32 AM
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WHEN USING AN ELECTRICAL
APPLIANCE, BASIC SAFETY PRECAUTIONS
SHOULD ALWAYS BE OBSERVED,
INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING
YOUR SHARK
POLARIZED PLUG:
To reduce the risk of electric shock, this appliance
has a polarized plug (one blade is wider than the
other). As a safety feature, this plug will fit into
a polarized outlet only one way. If the plug does
not fit fully into the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician.
DO NOT force into outlet or try to
modify to fit.
WARNING:
electric shock or injury, do not use
outdoors or on wet surfaces.
®
NAVIGATOR LIFT-AWAY
To reduce the risk of
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR INJURY:
GENERAL ELECTRICAL SAFETY:
1. Unplug from electrical outlet when not in use
and before servicing.
2. DO NOT use vacuum with a damaged cord or
plug. If appliance is not working as it should,
has been dropped, damaged, left outdoors,
or dropped into water, return it to EURO-PRO
Operating LLC for examination, repair, or
adjustment.
3. DO NOT pull or carry vacuum by the cord.
4. DO NOT unplug by pulling on cord; to unplug,
grasp the plug, not the cord.
5. DO NOT handle plug or appliance with wet
hands.
6. DO NOT run the vacuum over the power cord.
7. DO NOT use the cord as a handle.
8. DO NOT close a door on the cord.
9. DO NOT pull cord around sharp corners. The
use of an extension cord is not recommended.
10. DO NOT leave appliance when plugged in.
11. Keep cord away from heated surfaces.
12. Turn off all controls before plugging or
unplugging vacuum cleaner.
13. Always turn off this appliance before connecting
or disconnecting motorized nozzle.
14. Store your appliance with the power cord
secured around the two cord holders-as shown
in the storage instructions.
2 TOLL FREE: 1-800-798-7398
NV351_26_NV352_26_IM_ENG_SPA_101207.indd 2 10-12-08 9:32 AM
English
HOSE ATTACHMENTS:
1. DO NOT use if air flow is restricted; if the air
paths, the hose, or the accessories become
blocked, turn the vacuum cleaner off. Remove
all obstructions before you turn on the unit
again.
2. Keep the end of the hose and accessory
openings away from face and body.
3. Keep cleaning tools and hose suction openings
away from hair, face, fingers, uncovered feet, or
loose clothing.
4. Only use manufacturer’s recommended
attachments.
GENERAL USE:
1. Use only as described in this manual.
2. DO NOT put any objects into openings. DO
NOT use with any opening blocked; keep free
of dust, lint, hair, and anything that may reduce
air flow.
3. Keep your work area well lit.
4. Keep the vacuum moving over the carpet
surface at all times to avoid damaging the
carpet fibers.
5. DO NOT place vacuum on unstable surfaces
such as chairs or tables.
6. DO NOT allow young children to operate the
vacuum or use as a toy. Close attention is
necessary when used by or near children.
7. DO NOT use vacuum cleaner if it has been
dropped, damaged, left outdoors, or submerged
in water. Return to EURO-PRO Operating LLC
for examination, repair, or adjustment.
8. DO NOT use without dust cup and/or filters in
place.
DUST CUP/FILTERS/ACCESSORIES:
Before turning on the vacuum:
1. Make sure that all filters are thoroughly dry
after routine cleaning.
2. Make sure that dust cup and all filters are in
place after routine maintenance.
3. Make sure accessories are free of blockages.
4. Only use filters and accessories provided by
EURO-PRO Operating LLC. [Failure to do so will
void the warranty.]
GENERAL CLEANING:
1. DO NOT pick up large-sized objects.
2. DO NOT pick up hard or sharp objects such as
glass, nails, screws or coins that could damage
the vacuum cleaner.
3. DO NOT pick up smoking or burning objects
such as hot coals, cigarette butts, or matches.
4. DO NOT pick up flammable or combustible
materials such as lighter fluid, gasoline, or
kerosene or use vacuum in areas where they
may be present.
5. DO NOT pick up toxic solutions such as
chlorine bleach, ammonia, or drain cleaner.
6. DO NOT use in an enclosed space where
vapors are present from paint, paint thinner,
moth-proofing substances, flammable dust or
other explosive or toxic materials.
7. DO NOT vacuum up any liquids.
8. DO NOT immerse vacuum cleaner in water or
other liquids.
9. DO NOT use outdoors or on wet surfaces; use
only on dry surfaces.
10. Use extra care when cleaning on stairs.
SAVE THESE
INSTRUCTIONS
3ww w.sharkclean.com
NV351_26_NV352_26_IM_ENG_SPA_101207.indd 3 10-12-08 9:32 AM
This manual covers model number:
NV351 26
NV352 26
TECHNICAL SPECIFICATIONS
Voltage: 120V., 60Hz
Watts: 1200W
Amps: 10A
4 TOLL FREE: 1-800-798-7398
NV351_26_NV352_26_IM_ENG_SPA_101207.indd 4 10-12-08 9:32 AM
Contents
English
Thank you for
purchasing
the Shark®
Navigator
Lift-Away.
Getting Started 6
Mode 1: Upright Vac 8
Mode 2: Detachable Canister 10
Above-Floor Cleaning 11
With Floor Nozzle 11
Storing 12
Maintenance 12
Emptying the Dust Cup 13
Cleaning the Pre-Motor Filters 13
Cleaning the Post-Motor HEPA Filter 14
Cleaning the Turbo Brush 14
Cleaning the Motorized Floor Brush 15
Checking for Blockages 15
Ordering Parts 16
Troubleshooting Guide 17
Warranty 18
5ww w.sharkclean.com
NV351_26_NV352_26_IM_ENG_SPA_101207.indd 5 10-12-08 9:32 AM
Getting Started
a
f
b
c
g
h
d
i
e
FIRST THING’S FIRST, YOU NEED TO KNOW
WHAT’S IN THE BOX YOU JUST OPENED:
a Handle with Stretch Hose
b Accessory Holder
c Extension Wand
d Detachable Canister
e Motorized Floor Brush Nozzle
f Crevice Tool
g 24” Crevice Tool (NV352 only)
h Dusting Brush
i Turbo Brush
6 TOLL FREE: 1-800-798-7398
Fig. 1
Fig. 3
Fig. 2
Fig. 4
ACCESSORIES:
CREVICE TOOL
Reach deep into narrow spaces and clean between
cushions, under radiators and baseboards and in
hard to reach crevices and corners. (Fig. 1)
DUSTING BRUSH
Dust shelves, lamp shades, window blinds, books,
furniture and other upholstered household items.
(Fig. 2)
ACCESSORY HOLDER
Designed to hold the crevice tool and dusting brush.
For quick access to tools when vacuuming and
cleaning around the house. (Fig. 3)
TURBO BRUSH
This unique tool was engineered for fast and
easy removal of pet hair and ground in dirt from
carpeted stairs and upholstery. (Fig. 4)
NV351_26_NV352_26_IM_ENG_SPA_101207.indd 6 10-12-08 9:32 AM
Your new Shark® Navigator Lift-Away vacuum cleaner can easily be configured into different
cleaning modes to meet all your cleaning needs: upright vacuum and detachable canister - both
with constant suction power.
English
Fig. 5
Fig. 6
MODES:
1 UPRIGHT VAC
Upright vacuuming - floors and carpets. (Fig. 5)
2 DETACHABLE CANISTER
Take the detachable canister with you around the
house to clean all kinds of hard to reach places.
(Fig. 6)
7ww w.sharkclean.com
NV351_26_NV352_26_IM_ENG_SPA_101207.indd 7 10-12-08 9:32 AM
Mode 1: Upright Vac
To reduce the risk of electric shock, unplug the unit before assembling, adding or removing attachments or
converting modes.
WARNING: The On/Off switch is on the top of the detachable canister. Always ensure the power is OFF
(“O” position) before plugging and unplugging.
d
Fig. 7 Fig. 8 Fig. 9
TO ASSEMBLE:
1 Place the floor nozzle on a level surface.
2 Align the tube of the floor nozzle with the tube on
the detachable canister and lower until you hear
the two pieces click into place. (Fig. 7)
When attaching the motorized floor brush, ensure
that the latching mechanism is fully locked in place
to ensure electrical connection has been made.
3 Attach the end of the extension wand to the tube
on the back of the detachable canister until it
clicks into place. (Fig. 8)
4 Slide the accessory holder (a) positioned opposite
the upper cord wrap, over the extension wand.
Align the tab with the groove and push down.
(Fig. 9)
Upper
Cord
b
a
Storage
Wrap
c
e
5 Push the handle (b) onto the top of the extension
wand until you hear it click into place. (Fig. 9)
6 Insert the end of the stretch hose (c) into the
connector on the back of the detachable canister.
(Fig. 9)
7
Store the dusting brush (d) and the crevice tool
(e) on the mounts of the accessory holder.
(Fig. 9)
8 TOLL FREE: 1-800-798-7398
NV351_26_NV352_26_IM_ENG_SPA_101207.indd 8 10-12-08 9:32 AM
English
Cord
Hook
a
b
c
Fig. 10
Suction
Release Collar
d
TO USE:
1 Rotate the cord release to quickly release the
power cord.
2 Secure the power cord in the cord hook (a).
(Fig. 10)
= Brush Roll ON
= Bare Floor
= OFF
3 Press the On/Off switch (b) to the “I” position to
vacuum bare floors (straight suction only) or to the
“II” position to engage the motorized floor brush
(for vacuuming carpets and rugs). (Fig. 10)
IMPORTANT: The motorized brush indicator light
(c) will illuminate green when motorized floor
brush is on, or red if there is a blockage or jam.
(Fig. 10) This feature is designed to protect your
Lifetime Belt that powers your motorized floor
brush. See Checking for Blockages on page 15.
Release suction
for easier push &
pull on high pile
carpets and area
rugs.
Fig. 11
4 Gently press the floor nozzle down with your foot
while you grasp the handle and tilt it back towards
you. (Fig. 11)
NOTE: The rotating brush on the motorized
floor brush will not spin unless the nozzle is flat
against the floor and the handle is tilted back.
5 Due to the huge suction power of this
vacuum, it may become necessary at
times to adjust the suction release (d)
on the handle. (Fig. 10) If the vacuum
seems difficult to push or pull or if
it is lifting up area rugs, adjust the
suction release by rotating the collar 90°
counterclockwise to open the valve. Rotate
the collar clockwise to close the valve when
you need high suction and for vacuuming
floors.
6 Empty dust cup after vacuuming and periodically
during use when it appears full. (See
“Maintenance” section for instructions.)
7 When you are finished vacuuming, turn the
vacuum off.
9ww w.sharkclean.com
NV351_26_NV352_26_IM_ENG_SPA_101207.indd 9 10-12-08 9:32 AM
Mode 2: Detachable Canister
You can carry your vacuum cleaner in both
modes by the carry handle located on top of
the dust cup.
a
b
Fig. 12
LIFT AWAY DETACHABLE CANISTER FOR
PORTABLE CLEANING
1 Separate the detachable canister from the floor
nozzle. (See page 8, Fig. 7.)
2 Press the handle release button (a) and pull the
handle up or press the extension wand release
button (b) and pull the extension wand up.
(Fig. 12)
10 TOLL FREE: 1-800-798-7398
NV351_26_NV352_26_IM_ENG_SPA_101207.indd 10 10-12-08 9:32 AM
3 Attach desired accessory onto the end of either
the extension wand or the ha
4 Press the On/Off switch to the “I” position to
turn the vacuum on for above-floor cleaning and
hold the handle in one hand while you carry the
detachable canister around the house with the
other hand. (Fig. 13)
Fig. 13
ndle.
Above-Floor Cleaning
With Floor Nozzle
English
a
Fig. 14
CLEAN ABOVE THE FLOOR IN UPRIGHT VAC OR
DETACHABLE CANISTER MODE
1 Press the handle release button and pull the
handle up or press the extension wand release
button and pull the extension wand up.
2 Attach desired accessory onto the end of either
the extension wand or the handle. (Fig. 14)
3 Your vacuum has tremendous suction
power. Adjust the amount of suction with
the suction release on the handle. Open
the valve (a) by rotating the collar 90˚
counterclockwise for low suction when
doing light jobs such as drapes or fine
surfaces. Close the valve (a) by rotating
the collar clockwise 90˚ for high suction
and when using the hand held turbo brush.
(Fig. 14)
4 Press the On/Off switch to the “I” position to turn
the vacuum on for above-floor cleaning.
IMPORTANT: Ensure vacuum is in upright
position. Do not use position “II” when cleaning
above the floor in the upright vac mode as this
will engage the motorized floor brush. The
rotating brush may damage your floor if run for a
prolonged period of time in one area.
Suction
Release Collar
Release suction
for easier push &
pull on high pile
carpets and area
rugs.
Fig. 15
CLEAN THE FLOOR IN DETACHABLE CANISTER
MODE
1 Press the extension wand release button and pull
the extension wand up.
2 Attach either floor nozzle onto the end of the
extension wand. (Fig. 15)
3 Press the On/Off switch to the “I” position to turn
the suction motor on.
NOTE: The rotating brush will not rotate in
Detachable Canister mode.
11ww w.sharkclean.com
NV351_26_NV352_26_IM_ENG_SPA_101207.indd 11 10-12-08 9:32 AM
Storing
Lower
Cord
Storage
Clip
Quick
Cord
Release
Maintenance
To reduce the risk of electric shock, unplug the unit
before performing any cleaning, maintenance, or
troubleshooting checks.
Reassemble all parts securely before operating
vacuum.
DO NOT operate the vacuum without the pre-
motor filters and dust cup in place.
DO NOT operate the vacuum with WET filters.
IMPORTANT: Make sure all filters are completely
dry before inserting back into vacuum.
WARNING: Never insert sharp objects into any
opening to clear an obstruction.
IMPORTANT: Damages caused while clearing
or attempting to clear blockages are not covered
under your product’s limited warranty.
Fig. 16
STORE YOUR VACUUM SAFELY
1 Convert your vacuum back to upright vac mode.
2 Rotate the upper quick cord release to its upright
position and coil the power cord loosely around
the two clips. Clip the plug onto the cord to
secure. (Fig. 16)
3 Store the dusting brush and the crevice tool on the
mounts on the accessory holder.
4 Store your vacuum cleaner safely in a cool dry area
where it will not be a hazard, will not get damaged
and will not cause damage to anyone or anything.
NOTE: Empty dust cup after cleaning and prior
to storing. (See “Maintenance” section for
instructions.)
12 TOLL FREE: 1-800-798-7398
NV351_26_NV352_26_IM_ENG_SPA_101207.indd 12 10-12-08 9:32 AM
Fig. 17 Fig. 18
Loading...