Shark Navigator NV100 Owner's Manual

www.sharkclean.com

NV100

Owner’s Guide
Manual del usuario

TOL L FREE : 1-8 00-79 8-739 8 1ww w.sha rkcle an.c om

Engl ish

Contents

Important Safety Instructions 2

Getting Started 4

Assembly 4

Using the Vacuum 6

Emptying the Dust Cup Assembly 7

Proper Care of Your Vacuum 8

Troubleshooting 9

Checking for Blockages 10

Maintenance 11

Warranty and Registration 13

Thank you for
purchasing
the Shark®

Navigator™

Vacuum.

This manual covers model:

NV100 26

TECHNICAL SPECIFICATIONS

Voltage: 120V.

Watts: 700W

Amps: 5.83A

Hertz : 60Hz

2 TOL L FREE : 1-8 00-79 8-739 8 3ww w.sha rkcle an.c om

Engl ish

WARNING:

TO REDUCE THE RISK OF ELECTRIC
SHOCK OR INJURY DO NOT USE
OUTDOORS OR ON WET SURFACES.

GENERAL CLEANING:

20. DO NOT run the vacuum over large-sized

objects.

21. DO NOT pick up hard or sharp objects such as

glass, nails, screws or coins that could damage
the vacuum cleaner.

22. DO NOT pick up smoking or burning objects

such as hot coals, cigarette butts or matches.

23. DO NOT pick up flammable or combustible

materials such as lighter fluid, gasoline,
kerosene or use in areas where they may be
present.

24. DO NOT pick up toxic solutions such as

chlorine bleach, ammonia or drain cleaner.

25. DO NOT use in an enclosed space where

vapors are present from paint, paint thinner,
moth-proofing substances, flammable dust or
other explosive or toxic materials.

26. DO NOT vacuum up any liquids.

27. DO NOT immerse vacuum cleaner in water or

other liquids.

28. DO NOT use outdoors or on wet surfaces; use

only on dry surfaces.

29. Use extra care when cleaning on stairs.

30. Before turning on the vacuum:

• Make sure that dust cup, and all filters are in
place after routine maintenance.

• Make sure that all components and filters are
thoroughly dr y after routine cleaning.

• Only use filters and accessories provided by
EURO-PRO Operating LLC [Failure to do so
will void the warranty]

WHEN USING YOUR SHARK®
NAVIGATOR

™

VACUUM, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED, INCLUDING THE FOLLOWING:

READ ALL INSTRUCTIONS BEFORE USING
YOUR SHARK

®

NAVIGATOR™ VACUUM.

POLARIZED PLUG:

This appliance has a polarized plug (one blade
is wider than the other). As a safety feature, this
plug will fit into a polarized outlet only one way.

Do not force into the outlet or try to
modify the plug to fit.

GENERAL ELECTRICAL SAFETY:

1. Unplug from elec trical outlet when not in use
and before servicing.

2. DO NOT use vacuum with a damaged cord or
plug.

3. DO NOT pull or carry vacuum by the cord.

4. DO NOT unplug by pulling on cord; to unplug,
grasp the plug, not the cord.

5. DO NOT handle plug or vacuum cleaner with
wet hands.

6. DO NOT run the vacuum over the power cord.

7. DO NOT close a door on the cord.

8. DO NOT pull cord around sharp edges or
corners.

9. DO NOT leave appliance when plugged in.

10. Keep power cord away from heated surfaces.

11. Turn off all controls before plugging or
unplugging vacuum cleaner.

GENERAL USE:

12. Use only as described in this manual.

13. DO NOT put any objects into openings.

14. Keep your work area well lit.

15. Keep the vacuum moving over the carpet
surface at all times to avoid damaging the
carpet fibers.

16. DO NOT place vacuum on unstable surfaces
such as chairs or tables.

17. DO NOT allow young children to operate the
vacuum or use as a toy.

18. Close attention is necessary when used by or
near children.

19. DO NOT use vacuum cleaner if the appliance
is not working as it should, has a damaged plug
or cord, if the unit has been dropped, damaged,
left outdoors or submerged in water. Return
to EURO-PRO Operating LLC for examination,
repair or adjustment.

IMPORTANT SAFETY INSTRUCTIONS

For Household Use Only

HOSE ATTACHMENTS:

31. DO NOT put any object into openings. Do not

use with any opening blocked. Keep free of lint,
hair and anything that may reduce airflow.

32. DO NOT use if air flow is restricted; if the air

paths, the hose or the extension tube become
blocked, turn the vacuum cleaner off. Remove
all obstructions before you turn on the unit
again.

33. Keep the end of the hose, wands and other
openings away from face, body and loose
clothing.

34. Keep rotating brush and suc tion openings away
from hair, face, fingers, uncovered feet or loose
clothing.

35. Only use manufacturer’s recommended
attachments.

SAVE THESE
INSTRUCTIONS

4 TOL L FREE : 1-8 00-79 8-739 8 5ww w.sha rkcle an.c om

Engl ish

8 TO CARRY THE VACUUM:

With the unit in the standing

position, lift by the Dust Cup
Handle (carry handle).

CAUTION: When lifting or

carrying, DO NOT press Dust
Cup release button ( ).

Fig. 1

FIRST THING’S FIRST, YOU
NEED TO KNOW WHAT’S IN THE
BOX YOU JUST OPENED:

A Handle

B Extension Wand

C Stretch Hose

D Dust Cup

Getting Started

YOUR SHAR K® NAVIGATOR™
IS EASY TO ASSEMBLE:

1 Place your vacuum body upright

on a level surface.

2 Insert the hose connector into

the opening on the back of the
vacuum body. (Fig. 1)
NOTE: Once the hose connector
has been inser ted, it cannot be
removed.

3 Insert the handle with the

extension wand into the top of
the vacuum until secure.
(Fig. 2)

4 Insert the stretch hose into the

hose connec tor on the back of
the unit. Make sure that it snaps
in place. (Fig. 3)

5 Store your on-board tools onto

the accessory holder located
on the back of the unit.

(Fig. 4)

NOTE: The accessory holder is
removable. In order to remove
or attach the accessory holder,
you must remove the dust cup
first. To remove the accessory
holder, just hold the tab (a),
rotate left and pull out. To
replace, align the pins into
the hinges (b) on the vacuum.
Rotate it fully to secure. (Fig. 5)

6 When storing your vacuum,

wind the power cord around
the two cord holders and secure
with cord clip. (Fig. 6)

7 There is a Quick Cord Release

on the top cord holder. Simply
turn to the lef t or right to
release the power cord. To store
the unit, the cord holder should
be in the upright position.

IMPORTANT: For suction to

reach the power nozzle, the
extension wand and stretch
hose must be at tached securely
on the vacuum body.

Assembly

Not all accessories are available
on all models.

Fig. 6

Fig. 2

Fig. 4

F

H

A

E

C

D

B

E Hose Connector

F Vacuum Body

G Accessory Holder

H Power Nozzle

Optional tools are available for sale
for any NV100 model. To order
additional pa rts or accesso ries go
to www.sharkcle an.com.

G

Fig. 3

Hose Connect or

Fig. 5

b

a

6 TOL L FREE : 1-8 00-79 8-739 8 7ww w.sha rkcle an.c om

Engl ish

Using the Vacuum

Your Shark® Navigator™ can be
used to clean all surface types.

1 Plug in the vacuum.

2 Push the “Power” button.

(Fig. 7)

3 Place your foot on the power

nozzle and pull the handle back
towards you. (Fig. 8)

NOTE: This vacuum has a

separate “Brushroll” button on
the top of the vacuum. (Fig. 9)

4 CLEAN CARPETS:

Engage the brushroll by pushing

the “Brushroll” button to the
“ON” position. The brushroll
light will turn green. (Fig. 9)

IMPORTANT: To protect your

carpets, the brushroll will only
turn on when you have pulled
the handle back towards you
and released the power nozzle.

IMPORTANT: The brushroll

indicator light on the power
nozzle will illuminate solid red if
there is a blockage. (Fig. 10) This
feature is designed to protect
your Lifetime Belt that powers
your brushroll. See Checking
for Blockages on page 10.

5 CLEAN BARE FLOORS:

For cleaning bare floors or to

clean with the hose, push the
“Brushroll” button to the “OFF”
position for suction only. The
brushroll light will turn off. The
brushroll will not spin in this
mode.

Indicator Light

6 CLEAN ABOVE-FLOORS WITH

HOSE:

You can attach the accessories onto
the handle or onto the extension
wand for a longer reach.

a Stand the vacuum into upright

position.

b To remove the handle only, press

the handle release button.
(Fig. 11)

c To remove the handle with

the extension wand, press the
extension wand release button
on the back of the vacuum.
(Fig. 12)

d Push the selected tool into the

end of the handle or handle with
extension wand for longer reach
and begin cleaning.

To order additional parts and accessories,
go to www.sharkclean.com.

The height of your power nozzle has been
optimized for easy pushing and superior
cleaning on all floor types. There is no need
to make any height adjustments as you
transition to different floor & carpet types.

Fig. 10

Always hold the vacuum when using
the hose to clean so that it does not
tip over.

DO NOT pull vacuum cleaner around by

the hose.
DO NOT over-extend the hose.

Fig. 11

Fig. 18

Fig. 14

Fig. 15

Fig. 16

Fig. 17

Fig. 12

Fig. 7

Fig. 13

Dust cup

Release

Button

Emptying the Dust Cup Assembly

For best results empty the Dust Cup Assembly after

each use; or as needed during prolonged usage. or
when it reaches the MAX fill line.

DO NOT OVERFILL.
Turn vacuum off before emptying.

TO EMPTY THE DUST CUP
ASSEMBLY:

1 Press the Dust Cup release

button ( )and remove the dust
cup from the vacuum. (Fig. 13)

2 Grip carry handle and press the

bottom Dust Cup Door release
button. (Fig. 14)

3 Option A: for Quick Empty:

Insert Dust Cup Assembly deep
inside trash receptacle to contain
dust and debris. (Fig. 15)

Press the bottom Dust Cup Door

release button; tap container
gently to dislodge and release
dust and debris.

Close the bottom door until it

snaps in place.

Important: If the Dust Cup

Door does not swing open freely
after pressing the release button,
push the door open using the
bottom door tabs.

4 Option B: For Allergy Sufferers:

Wrap a trash bag around the
Dust Cup Assembly leaving
space at the bottom for the door
to swing open. (Fig. 16)

Locate the Dust Cup Door

release button within the trash
bag and press to release as you
shake the dust cup to empty
dust and debris.

Close the bottom door until it

snaps in place.

Note: Option B can also be

performed outside of the home
to further minimize releasing
dust back into the air. Carry just
the Dust Cup Assembly and trash
bag outside.

Note: It may become necessary

to occasionally clean the metal
screen inside the dust cup. To
clean, press the top dust cup
release button (Fig. 17), pull out
the metal screen and remove
any excess dirt. Then replace the
metal screeen inside the dust
cup and close the top lid.
(Fig. 18)

Fig. 8

Fig. 9

8 TOL L FREE : 1-8 00-79 8-739 8 9ww w.sha rkcle an.c om

Engl ish

Troubleshooting

WARNING:

To reduce the risk of electric shock, the power cord must be disconnected before
performing maintenance/troubleshooting checks.

To purchase replacement parts, please visit our website: www.sharkclean.com .

PROBLEM POSSIBLE REASONS & SOLUTIONS

Vacuum will not run.

Check to see if the vacuum is plugged in properly.
Check the circuit breaker/fuse.
Check the On/Off button.

Vacuum is not
picking up dirt.

Airflow is restricted. No
suction or light suction.

Check filters to see if they need cleaning. Follow instructions for rinsing
and drying the filters before re-inserting back into the vacuum. (See
“Maintenance” sections for instructions.)

Dust cup may be full; empty dust cup.
Check hose and hose connections for blockages; clear blockages if required.
If dust cup is empty, and attachment inlets are clear, check for other

blockages. (See “Checking for Blockages” for instructions.)

Brush roll does not turn
on.

Press the “Brushroll” button to the “ON” position. The brushroll light near
this button will illuminate green when “ON”.

Place your foot on the floor brush and pull the handle back to engage the
brushroll.

If the red light on the power nozzle is illuminated, see the section on
Checking for Blockages.

Vacuum turns off on its
own.

This vacuum cleaner is equipped with a motor protective thermostat. If for
some reason your vacuum overheats, the thermostat will automatically turn
the unit off. Should this occur, perform the following steps to restart the
motor thermostat:

1. Press the “Power” button to the (Off) position.

2. Unplug the vacuum.

3. Empty the dust cup and clean filters. (See “Maintenance” sections for
instructions.)

4. Check for blockages in hose, accessories and inlet openings.
(See “Checking for Blockages” for instructions.)

5. Allow the unit to cool for a minimum of 45 minutes.

6. Plug in the vacuum.

7. Press the “Power” button to the (On) position to restart the vacuum.

Note: If vacuum still does not start, contact Customer Service at:
1-800-798-7398.

Proper Care of Your Shark® Upright Vacuum

COMPONENT

MAINTENANCE SCHEDULE

Rinse and air dry every month under normal use.

Empty each time you vacuum.

Pre-Motor Foam Filter

Dust Cup

Rinse and air dry every month under normal use.

Pre-Motor Felt Filter

Clean once every 12 months under normal use.

Post-Motor Filter

1

2

3

4

DO NOT put the filters in the washing machine or dishwasher.

NOTE: The material in the filter will discolor over time. This is

NORMAL and will not affect the performance of the filter.

CAUTION:

Unplug
the vacuum while
cleaning filters; failure
to do so might result
in electric shock.

CLEANING THE PRE-MOTOR
FILTERS

1 Remove the dust cup.

2 Pull the 2 filters out from the

top of the motor base.

(Fig. 19)

3 Rinse the filters thoroughly in

lukewarm water until the water
runs clear.

4 Squeeze out excess water and

let air-dry for at least 24 hours
before replacing. Do not use
a hair dryer or other heating
methods to dr y.

5 Place the felt filter in first, then

the foam filter.

6 Replace the dust cup.

Fig. 20

CLEANING THE POST-MOTOR
FILTER

1 Remove the filter cover from

the front of the vacuum by
pulling up on the tab and
pulling the cover away from the
vacuum. (Fig. 20)

2 Remove the filter from the

frame and wash the filter under
the tap using lukewarm water.

3 Allow the filter to air dry for 24

hours. Do not use a hair dryer
or other heating methods to
dry.

4 Once the filter is dry, replace it

back into the vacuum.

5 Replace the cover by inserting

the two tabs into the holes at
the top and and then swinging
the cover down until it clicks
into place.

NOTE: Filters may appear dirty
but frequent cleaning of these is
not necessary. See maintenance
schedule above.

Pre-Motor

Foam Filter
Felt Filter

Fig. 19

IMPORTANT: Loss of Suction may

occur if foam filters are not cleaned
every month. Rinse and allow to air dry
completely.
Foam filters may appear dirty after use ­this is normal.