www.SharkVacThenSteam .com
VAC-THEN-STEAM™
MV2010WC
OWNER’S GUIDE
MV2010WC_11_IB_ENG_100803.indd 1 04/08/10 9:37 AM
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WHEN USING YOUR SHARK® VAC-
THEN-STEAM™, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS
BE FOLLOWED, INCLUDING THE
FOLLOWING:
WARNING:
THE RISK OF FIRE , ELECTRIC
SHOCK OR INJURY READ ALL
INSTRUCTIONS BEFORE USING
YOUR SHARK
DANGER OF SCALDING.
Please use caution when using the
steam function. The steam emitted
from the appliance is very hot.
1. Use the system only for its
intended use.
2. DO NOT use outdoors. Use only
on dry, indoor surfaces.
3. DO NOT leave the appliance
unattended when plugged in. Always
unplug the power cord from the
electrical outlet when not in use and
before servicing.
4. DO NOT allow the appliance to be
used by children. Close attention
is necessary when used by or near
children, pets or plants.
5. DO NOT operate the appliance with
a damaged plug or cord, or if the
unit has been dropped, damaged,
left outdoors or dropped into water.
To avoid the risk of electric shock,
do not disassemble or attempt to
repair the appliance on your own.
Return the appliance to EURO-PRO
Operating LLC (see warranty) for
examination and repair. Incorrect reassembly or repair can cause a risk of
electrical shock or injury to persons
when the appliance is used.
6. Use only as described in this manual.
7. Use only manufacturer’s
recommended accessories and
replacement pads.
®
VAC-THEN-STEAM™.
TO REDUCE
8. To protect against a risk of electric
shock, DO NOT immerse the appliance
into water or any other liquids.
9. DO NOT handle plug or appliance
with wet hands or operate appliance
without shoes.
10. DO NOT pull or carry by power cord,
use power cord as a handle, close a
door on the power cord, or pull the
power cord around sharp edges or
corners. Do not run appliance over
cord. Keep power cord away from
heated surfaces.
11. DO NOT unplug by pulling on power
cord. To unplug, grasp the plug not
the power cord. Do not use extension
cords or outlets with inadequate
current carrying capacity.
12. DO NOT put any objects into the unit
openings. Do not use the unit if any
opening is blocked; keep free of dust,
lint, hair and anything that may reduce
airflow.
13. DO NOT put hands or feet under the
Vac-Then-Steam™. Unit gets very hot
and may burn.
14. Use ONLY on flat, horizontal surfaces.
Do not use on walls, counters or
windows.
15. DO NOT use on leather, wax polished
furniture and floors, synthetic fabrics,
velvet or other delicate, steam
sensitive materials.
16. DO NOT add cleaning solutions,
scented perfumes, oils or any other
chemicals to the water used in this
appliance as this may damage the unit
or make it unsafe for use and void the
warranty. If you live in a hard water
area, we recommend using distilled
water in your Vac-Then-Steam™.
17. When in use, NEVER turn the
appliance over or on its side. NEVER
DIRECT STEAM TOWARDS PEOPLE,
ANIMALS OR PL ANTS.
18. NEVER LEAVE THE CLEANING UNIT
IN ONE SPOT ON ANY SURFACE FOR
ANY PERIOD OF TIME WHE N MICROFIBER PAD IS ATTACHED.
19. Carefully remove the micro-fiber pad
immediately after you have unplugged
and allowed the appliance to cool.
20. When cleaning the appliance, unplug
the power cord from the electrical
outlet and clean with a dry or damp
cloth. Do not pour water or use
alcohol, benzene or paint thinner on
the unit.
21. Extreme caution should be exercised
when using this appliance to clean
stairs.
22. Never use Steam function without
micro-fiber pad attached.
23. Keep your work area well lit.
24. Store appliance indoors in a cool,
dry place.
25. To avoid circuit overload, do not
operate another appliance on the
same socket (circuit) as the cleaning
unit.
26. If an extension cord is absolutely
necessary, an extension cord rated a
minimum of 15 ampere, 14 gage cord
should be used. Cords rated for less
amperage may overheat. Care should
be taken to arrange cord so that it
cannot be pulled or tripped over.
27. DO NOT store unit with damp/wet
micro-fiber cleaning pad attached.
28. DO NOT use the vacuum cleaner
without dust cup and filter in place.
29. DO NOT vacuum up any liquids.
30. DO NOT pick up anything that is
burning or smoking such as cigarettes,
matches or hot ashes.
31. To reduce the risk of fire DO NOT use
to pick up flammable or combustible
liquids such as gasoline or use
vacuum in areas where flammable or
combustible fumes may be present.
32. DO NOT pick up toxic solutions such
as chlorine bleach, ammonia or drain
cleaner with the cleaning unit.
33. DO NOT use in an enclosed space
where vapors are present from
paint, paint thinner, mothproofing
substances, flammable dust or other
explosive or toxic materials.
34. DO NOT run the cleaning unit over
large-sized objects.
35. DO NOT pick up hard or sharp objects
such as glass, nails, screws or coins
that could damage the cleaning unit.
36. DO NOT place appliance on unstable
surfaces such as chairs or tables.
37. DO NOT allow the cleaning unit to be
used as a toy.
38. Close attention is necessary when
used near children.
39.Keep hair, loose clothing, fingers
and all parts of the body away from
openings and moving parts.
40.Turn off all controls before plugging or
unplugging your Vac-Then-Steam™.
WARNING: Your appliance is designed
to clean non-carpeted, sealed hard
floor surfaces that will withstand high
heat. Do not use on unsealed wood or
unglazed ceramic floors, on surfaces
that have been treated with wax or on
some no wax floors. The sheen may
be removed by the heat and steam
action. It is always recommended to
test an isolated area of the surface to
be cleaned before proceeding. We
also recommend that you check the
use and care instructions provided by
the floor manufacturer.
POLARIZED PLUG:
TO REDUCE THE RISK OF ELECTRIC
SHOCK , this appliance has a polarized
plug (one blade is wider than the
other). As a safety feature, this plug
will fit into a polarized outlet only
one way. If the plug does not fit fully
into the outlet, reverse the plug. If it
still does not fit, contact a qualified
electrician.
DO NOT
ATTEMPT
TO DEFEAT
THIS SAFETY
FEATURE .
SAVE THESE
INSTRUCTIONS
ww w.S harkVa cThe nSteam .comTOL L FREE : 1 -8 00 -79 8-73 98
MV2010WC_11_IB_ENG_100803.indd 2-3 04/08/10 9:37 AM
Steam Technology
Contents
Eng lis h
Thank you for purchasing the
®
Shark
Vac-Then-Steam™,
the complete bare floor
cleaning system.
The unique steam technology,
turns simple tap water into
super-heated steam that infuse
the micro-fiber pads for chemical
free cleaning. Only this method
creates and delivers 212°F
steam that is effective enough
to clean and sanitize all your
hard floor surfaces. The Shark®
Vac-Then-Steam™ can help you
achieve a truly clean and healthy
environment for you and
your family.
Getting Started: Assembly 2
Getting Started: Mode Controls 4
Vacuum Mode 5
Steam Mode 8
Maintaining Your Vac-Then-Steam™ 12
Troubleshooting Guide 14
Warranty and Registration 15
Visit www.SharkVacThenSteam.com for
more helpful hints and support.
THIS BOOK COVERS MODEL NUMBER:
MV2010WC 11
TECHNICAL SPECIFICATIONS
Voltage: 120V., 60Hz.
Power: 1550 Watts
Water
Capacity: 300 ml (10 oz.)
TOL L FREE : 1 -8 00 -79 8-73 98
MV2010WC_11_IB_ENG_100803.indd 4-1 04/08/10 9:37 AM
ww w.S harkVa cThe nSteam .com
1
Getting Started: Assembly
When assembling your Vac-Then-Steam™
there may be a little water in or around
the water tank. This is because we
quality test all our Shark products before
distributing them, so you get a quality
Shark® Vac-Then-Steam™.
a
c
Eng lis h
i
j
k
1
2
3
l
m
n
b
h
a Telescopic Handle
b Cleaning Unit with Dust Cup
c 1 All-Purpose Cleaning Pad and
1 Heavy Duty Cleaning Pad
d Steam Frame
e Storage Tray
f Filling Flask
g 1 Replacement Post-Motor Filter
h 1 Replacement Dust Cup Filters Set
d
o
q
p
e
r
f
g
i Mop Handle
j Quick Release Swivel Cord Wrap
k Cord Clip
l Telescopic Handle Latch
m Carry Grip
n Vacuum and Steam Mode Panel
o Water Tank Cap
p Water Tank Viewing Window
q Post-Motor Filter Access
r Dust Cup
ASSEMBLY
1 Slide the Telescopic Handle into the
cleaning unit until it locks into place.
Once in position, you never have to
remove the handle.
2 For your comfort, you can adjust the
height of the handle. To do so pull
the latch down on the handle tube
90 degrees to the open position.
Holding the handle, extend the tube
to the height that is right for you and
then close latch to lock into position.
3 Wrap cord around cord holders and
secure plug to cord.
NOTE: The Vac-Then-Steam™, is a
complete bare-floor cleaning and
sanitizing system. It comes “vacuumready” out of the box.
QUICK TIP: For easier pushing and
pulling, extend the height of the
handle by using the telescopic latch
on the pole.
2
MV2010WC_11_IB_ENG_100803.indd 2-3 04/08/10 9:37 AM
TOL L FREE : 1 -8 00 -79 8-73 98
ww w.S harkVa cThe nSteam .com
3
Getting Started: Vacuum and Steam Panel Vacuum Mode
STEAM MODE:
The Vac-Then-Steam™ has two
operating modes:
VACUUM MODE:
1
After inserting the telescopic handle,
your cleaning system is vacuum-ready.
Begin vacuuming your hard-surface
floors by tilting the cleaning unit back
and pressing the vacuum power button.
1
1
2
DO NOT USE STEAM PAD AND
FRAME IN VACUUM MODE
2
Eng lis h
3
3
OPERATING IN VACUUM MODE:
1 Remove steam pad and frame,
if attached. See page 11 for
instructions. Vacuum will not activate
if steam frame is attached.
2 SLIDE THE TOGGLE SWITCH UP to
expose the vacuum power button.
3 Press the VACUUM POWER BUTTON
to the ON “I” position to activate
the vacuum.
4
TOL L FREE : 1 -8 00 -79 8-73 98
3
OPERATING IN STEAM MODE:
1 Attach steam pad and frame.
Steam mode will not work if the pad
and frame are NOT attached. See
page 8 for assembly instructions.
2 Fill the water tank.
SLIDE THE TOGGLE SWITCH DOWN
to expose the Steam Power button.
3 Press the STEAM POWER BUTTON
to the ON “I” position. The button
will be illuminated red when steam
mode is activated.
4 Wait 30 seconds to heat water, then
TILT HANDLE BACK TO ACTIVATE
STEAM PUMP.
2
USING VACUUM MODE
1 Pull and twist the quick release cord
holder to unwrap the power cord
completely. Plug in the unit.
2 To vacuum, slide the toggle switch
until the vacuum power button is
exposed. Press the vacuum power
mode button to the ON “I” position.
IMPORTANT: You cannot use the
vacuum function if the frame and
pad are attached to the base of the
cleaning unit.
NOTE: Only vacuum sealed and
non-carpeted bare floor surfaces.
Refer to floor manufacturer
guidelines and warnings.
3 Place your foot lightly on the top
of the cleaning unit base. Tilt the
cleaning unit back. Vacuum your
floors.
IMPORTANT: Vacuum all surfaces
first before steam-cleaning to
avoid condensation build-up. Avoid
vacuuming after steam mopping.
NOTE: If you vacuum and then
steam-clean one room, before
moving on to the next, wait 10
minutes for the condensation to
clear before vacuuming again.
ww w.S harkVa cThe nSteam .com
5
MV2010WC_11_IB_ENG_100803.indd 4-5 04/08/10 9:38 AM
Vacuum Mode
2
1
Eng lis h
3
4
5
2
3
STORAGE
1 Place your foot lightly on the top of
the base. Tilt cleaning unit into the
upright position.
2 Turn off the vacuum power button
and unplug the unit.
3 Wrap cord around cord holders and
secure plug. Store cleaning unit in an
upright position.
IMPORTANT:
Always carry
the Vac-Then-
Steam™ by the
cleaning unit
collar; rather
than by the
handle.
1
EMPTYING THE DUST CUP
1 Press the dust cup latch at the
bottom of the canister upward. Pull
the dust cup assembly out and down.
2 Twist dust cup cover counter-
clockwise to open.
3 Tap canister gently over trash
receptacle to empty.
NOTE: Over time debris may gather
in the conical filter of your Vac-
Then-Steam™ and this may reduce
your vacuum’s performance. Clean
the filter often for optimal suction
performance.
6
4 Remove the filter frame from the
filter canister. Tap the filter canister
gently over trash receptacle to
empty the cone.
5 To reattach the dust cup cover, align
the indicators that are printed on the
rear of the dust cup and cover. Turn
the cover clockwise and make sure
the solid arrows are aligned before
reinserting the dust cup into the
vacuum.
6 To replace the dust cup in to the unit,
gently push the dust cup assembly
up and in. The dust cup will click
into place.
6
MV2010WC_11_IB_ENG_100803.indd 6-7 04/08/10 9:38 AM
TOL L FREE : 1 -8 00 -79 8-73 98
ww w.S harkVa cThe nSteam .com
7
Steam Mode
1
Eng lis h
Do not use chemicals or
detergents in your
Vac-Then-Steam™. You
only need water to achieve
super-heated, sanitizing
steam.
1
2
3
MAGNETIC
CONNECTIONS
ASSEMBLY
1 Attach a steam pad onto the bottom
of the steam frame, matching the
hook and loop fasteners.
2 Place the steam frame/pad assembly
on the floor with the magnetic
connections facing up.
8
MV2010WC_11_IB_ENG_100803.indd 8-9 04/08/10 9:38 AM
TOL L FREE : 1 -8 00 -79 8-73 98
3 Place the cleaning unit onto the
Steam Frame. THE UNIT MUST BE
UPRIGHT.
IMPORTANT: Steam frame and pad
must be attached to the cleaning unit
in order to use the steam function.
2
FILLING THE WATER TANK
1 Keep the cleaning unit in the upright
position to add water. Turn the water
tank cap counter-clockwise and
remove from the tank.
2 Use the filling flask and pour water
into the tank. Do not overfill. Replace
the cap on the water tank by turning
cap clockwise and tightening.
NOTE: If you live in a hard water
area, we recommend using distilled
water in your Vac-Then-Steam™.
ww w.S harkVa cThe nSteam .com
9
Steam Mode
1
2
Eng lis h
3
1
3
2
1
2
STORAGE
1 Unplug and turn the unit OFF “O”.
Press your foot on the steam frame.
STEAM CLEANING
1 Plug in the cleaning unit. Slide
the toggle switch to expose the
steam power button.
2 Press the steam power button to the
ON “I” position. The illuminated red
light indicates that the “boiler” is on.
Wait 30 seconds for the water to
heat up and for steam to be ready.
10
MV2010WC_11_IB_ENG_100803.indd 10-11 04/08/10 9:38 AM
TOL L FREE : 1 -8 00 -79 8-73 98
3 Place your foot lightly on the top of
the base. TILT HANDLE BACK TO
ACTIVATE STEAM PUMP.
4 Push handle upright to stop steam.
NOTE: Check water level and fill
anytime throughout the cleaning
process to maintain optimal steam.
Separate steam pad from steam
frame.
2 Remove the water tank cap and
empty water tank.
3 Wrap cord securely around cord
management hooks.
4 Store your Vac-Then-Steam™ in the
storage tray.
CAUTION : Use caution when
handling the steam frame. Magnetic
connections on the frame retain heat.
CARE OF YOUR MICRO -FIBER
CLEANING PAD
1 Wash pads in warm water. Wash
separately from other laundry. Only
use liquid detergent (no powder
detergent). Do not use fabric
softeners. Line dry or dry on a low
dryer setting.
2 If there are loose threads on the
pad carefully cut the threads with
scissors. Do not pull on them or cut
at the base.
ww w.S harkVa cThe nSteam .com
11
Maintaining Your Vac-Then-Steam™
Replacement filter sets have
been provided with your
product. Use one of the
replacement filter sets when
1
Thin Filter
Thick Filter
2
24
another set is drying.
Eng lis h
3
1
A replacement post-motor
filter has been provided
with your product. Use the
replacement filter while the
other is drying.
3
2
CARE OF YOUR DUST CU P FILTERS
1 Turn OFF “O” and then unplug the
vacuum. Pull out the dust cup. See
page 7 for instructions.
Lift the filter frame out from the top
of the dust cup. Remove the two
filter layers from the filter frame.
2 Thoroughly rinse the two filters in
lukewarm water. Squeeze out any
excess water. Air dry for 24 hours
before reusing.
3 Insert a dry filter set into the filter
frame. The order of the filters
impacts your dust cup performance.
Make sure the thick filter is on the
bottom and the thin filter is on top.
Put the frame with the filter set back
into the top of the dust cup.
12
MV2010WC_11_IB_ENG_100803.indd 12-13 04/08/10 9:38 AM
TOL L FREE : 1 -8 00 -79 8-73 98
RECOMMENDED MAINTENANCE
SCHEDULE: Using only water,
thoroughly rinse filters every 3
months and dry for 24 hours.
Replace filter set in the Vac-Then -
Steam™ once a year. More regular
filter care or replacement may be
required with excessive use.
POST-MOTOR FILTER
1 Twist the Shark® logo knob on the
post-motor cover counter-clockwise
to release cover.
2 Use both hands to grip cover on both
sides and pull cover toward you.
Gently peel the filter off the inside of
the cover. Thoroughly rinse the filter
in lukewarm water. Squeeze out any
excess water. Air dry for 24 hours
before reusing.
3 Insert a dry filter into the inside of
the cover. Snap cover onto the
Vac-Then-Steam™.
Twist the Shark
to secure cover.
®
logo knob clockwise
NOTE: Using only water, thoroughly
rinse filter every 3 months and dry
for 24 hours. Replace filter in the
Vac-then-Steam™ once a year. More
regular filter care or replacement
may be required with excessive use.
DO NOT use a hair dryer or any other
forced hot air to dry any of the filters.
NOTE: Any other servicing should be
performed by an authorized service
representative
ORDERING REPLACEMENT PARTS
Go to www.SharkVacThenSteam.com
to find replacement filters,
accessories, and microfiber pads.
ww w.S harkVa cThe nSteam .com
13
Troubleshooting Guide
PROBLEM POSSIBLE REASONS & SOLUTIONS
Your Vac-Then-Steam™ should be securely plugged into a
The Vac-Then-Steam™
will not turn on.
The Vac-Then-Steam™
will not make steam.
The Vac-Then-Steam™
leaves water on the floor.
The Vac-Then-Steam™
is hard to push.
The Vac-Then-Steam
is not picking up dirt.
120V AC electrical outlet only.
Check your fuse or breaker.
Switch Steam or Vacuum Power button to the ON “I”
position.
Make sure the water tank is filled to the indicated fill line.
Attach Steam Pad and Frame to base of the unit.
Switch Steam Power button to the ON “I” position.
TILT MOP HANDLE BACK TO GENERATE STEAM.
Check to see if your micro-fiber cleaning pad has absorbed
too much moisture. We recommend you unplug the
Vac-Then-Steam™ and replace the micro-fiber cleaning pad.
Make sure the steam pad is attached correctly.
Wait 30 seconds after switching Steam Power button ON
before mopping, allowing water to heat to a 212°F sanitizing
steam. If the unit is not allowed to heat properly, some
water may be emitted.
Make sure the steam pad is attached correctly.
Check to see if the cleaning pad is excessively dirty. Replace
if the pad is too dirty or wet.
Try increasing the height of the pole for better leverage by
rasing the height of the telescopic pole.
Check filters to see if they need cleaning. Follow instructions for rinsing and drying the filters before re-inserting
back into the unit. (See “Maintenance” sections for
instructions.)
™
Dust cup may be full. Empty the dust cup.
Check nozzle at the cleaning base for blockages. Clear
blockages if required.
Eng lis h
Euro-Pro One (1) Year Limited Warranty
EURO-PRO Operating LLC warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of the original purchase, when utilized for
normal household use, subject to the following conditions, exclusions and exceptions.
If your appliance fails to operate properly while in use under normal household conditions
within the warranty period, return the complete appliance and accessories, freight prepaid.
For Customer Service support, call 1 (800) 798-7398 or visit our website at
www.SharkVacThenSteam.com.
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating
LLC will repair or replace it free of charge. Proof of purchase date and a check made payable
to EURO-PRO Operating LLC in the amount of $19.95 to cover the cost of return shipping and
handling must be included. *
The liability of EURO -PRO Operating LLC is limited solely to the cost of the repair or
replacement of the unit at our option. This warranty does not cover normal wear of parts and
does not apply to any unit that has been tampered with or used for commercial purposes. This
limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage
due to faulty packaging or mishandling in transit. This warranty does not cover damage or
defects caused by or resulting from damages from shipping or repairs, service or alterations to
the product or any of its parts, which have been performed by a repair person not authorized by
EURO-PRO Operating LLC.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/
or conventional warranties. The responsibility of EURO-PRO Operating LLC warranty if any,
is limited to the specific obligations expressly assumed by it under the terms of the limited
warranty. In no event is EURO- PRO Operating LLC liable for incidental or consequential
damages of any nature whatsoever. Some states/provinces do not permit the exclusion or
limitation of incidental or consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state or province to province.
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of
purchase date and to attach tag to item before packing with your name, complete address and
phone number with a note giving purchase information, model number and what you believe
is the problem with the item. We recommend you insure the package (as damage in shipping
is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER
SERVICE”. We are constantly striving to improve our products, therefore the specifications
contained herein are subject to change without notice.
OWNERSHIP REGISTRATION CARD FOR
CANADIAN CONSUMERS ONLY
Please complete and return or call 1-800-798-7398 to register your new Shark® product
within ten (10) days of purchase . The registration will enable us to contact you in the event
a product defect is discovered. By returning this card you acknowledge to have read and
understood the instructions for use, and warnings set forth in the accompanying instructions.
RETURN TO: EURO-PRO Operating LLC, 4400 Bois Franc, St. Laurent, Quebec H4S 1A7
PURCHASER: ……………………………………………………………………………………………...........................................
ADDRESS: ………………………………………………………………………………………………..............................................
Visit www.SharkVacThenSteam.com for more
helpful hints and support.
14
MV2010WC_11_IB_ENG_100803.indd 14-15 04/08/10 9:38 AM
TOL L FREE : 1 -8 00 -79 8-73 98
DATE OF PURCHASE: …………………………………………………………………….. MODEL: ……………...................
NAME AND ADDRESS OF STORE: ………………………………………………………………….................................
ww w.S harkVa cThe nSteam .com
MV2010WC
15
Eur o-P ro O pe rati ng L LC
US: N ew ton , MA 0245 9
CAN : V ill e St- Lau ren t, Q C H 4S 1 A7
1- 80 0-79 8-73 98
ww w.S har kVa cThe nSt eam .co m
Cop yright © 201 0 E uro -Pr o Op era tin g LLC
Pri nte d in Chi na
Ill ust ration s may dif fe r fr om a ctu al p rod uct .
MV2 010 WC. E.10 08 03
MV2010WC_11_IB_ENG_100803.indd 16 04/08/10 9:38 AM
Loading...