Shark Lift-Away Pro Steam Pocket S3901 Quick Start Manual

USING YOUR REMOVABLE HANDHELD STEAMER

7 To remove the Handheld Steamer, press and hold down the Ha ndheld Release Buttons

while pulling out the Handheld Steamer. (fig. 7)

fig. 8

QUICK START GUIDE

Simple steps to get you cleaning
and sanitising with your new
Shark

®

LIFT-AWAY™

Pro

Steam Pocket

®

Mop S3901*.

GETTING
STARTED

Pro Steam Pocket® Mop

PROFESSION AL

PROBLEM POSSIBLE REASONS & SOLUTIONS

fig. 1

*For more detailed information please ref er to your owner’s guide.

1 Insert the Mop Handle into the Steam Mop H ousing. Make sure it is inserted pa st the

line printed on the pole. Secure the assembled han dle and pole by inserting the large
screw through the exposed hole and tightening with a p hillips or a flat head screw
driver. (fig. 1)

2 Slide the mop head into the clea ning

pad pocket. Secure the quick fasteners
on the top of the pocket. (fig. 2)

STEAM MOP ASSEMBLY

3 Push the mop head into the mop bo dy

until you hear it snap into place. (fig. 3)

4 Turn the water t ank cap counter clockwise and rem ove from the tank. Use the filling flask

to pour water into the tank. Do not overfill. Repl ace the cap on the water tank. (fig. 4)

NOTE: Sweep or vacuum your floors prior to cle aning with your Steam Mop.

We recommend using distilled water to prolong the li fe of your Shark

®

Steam Pocket® Mop.

fig. 2

fig. 3

fig. 4

USING YOUR STEAM MOP

5 Unwrap the power cord completely and plug into an e lectrical outlet.

The STEAM CONTROL button LED will flash blue.

6 Press the STEAM CONTROL button to sel ect your steam setting. Press the but ton once

for LO mode, twice for MED mode and thre e times for HI mode. Clean your floors with a
forward and backward motion. See t he Owner’s Guide for additional inf ormation on each
setting and specific usage

requirements. (fig. 5, 6)

NOTE: The Carpet Glider can be u sed to lightly steam your carpets. (fi g. 6)

fig. 6

fig. 7

LO - Light steam for quick dusting and b est dry time.

MED - Normal, every day steam cl eaning.

HI - Heavy cleaning and will leave floors d amp.

ATTACHING AND REMOVING CLEANING TOOLS

8 Att ach your desired cleaning tool by pressin g the nozzle of the tool onto the Handheld

Steame r until it clicks into place. (fig. 8)

9 When bei ng used as a Handheld Steamer the STEA M CONTROL light will always be solid

blue . Press and hold

the steam trigger to create steam. The steam mod e setting can be
ch anged by pressing the STEAM CONTROL but ton. The setting can be change d while
ste aming or when the Handheld Steamer is at rest .

10 To remove the cleaning tool, p ress and hold down the Handheld Re lease Buttons then

sli de the cleaning tool off the Handh eld Steamer using the grips on the tool.

NOTE: Reference your Owner’s Guide for mo re information and detailed inst ructions
on using your cleaning tools.

CAUTION: Do not press the steam trigge r until the Cleaning Tool is snapped into th e
main nozzle of your Handheld Steamer

fig. 5

Your steam mop should be securely plugged into an electrical outlet only. Check your fuse or breaker.

Is there water in the water tank? If not, add water to your steam mop following instructions on page 5 of your owners guide.
If the unit still does not make steam, follow the decalcification instructions in your owner’s guide.

If you have already plugged in your unit, unplug and try a different outlet. This may reset the standby mode.
Add water to the tank and press the STEAM CONTROL button to select a steam setting.

Check to see if your cleaning pad is soaked through. If so, we recommend you unplug the steam mop
and change the cleaning pad. Make sure the cleaning pad is attached correctly.

Do not leave your steam mop on the floor with a damp or wet

cleaning pad. If you are using tap water,

we recommend switching to distilled water. Make sure the water tank door is closed securely.

Make sure the cleaning pad is attached correctly.
Check to see if the cleaning pad is excessively dirty. Replace if the cleaning pad is too dirty or wet.

The Lift-Away™
Pro Steam Pocket

®

Mop S3901

will not turn-on.

The unit will not
make steam.

Cannot activate steam
flashing blue light remains on.

The Lift-Away

™

Pro Steam Pocket

®

Mop S3901

leaves water on the floor.

The Lift-Away

™

Pro Steam Pocket

®

Mop S3901

left a white spot on the floor.

Floors are cloudy, streaky
or spotty after steaming.

The Lift-Away

™

Pro Steam Pocket

®

Mop S3901

is hard to push.

• The pad might be dirty, change the pad.

• If you washed the cleaning pad with powder detergent, your pad may be damaged and needs replacement.

• You might have left the mop in the same spot for too long.

• Do you have hard water? If you do, we recommend you switch to distilled water.

• This might be leftover residue. Use the steam mop a few more times and see if the leftover cloudiness is removed.
If this does not work, we suggest rinsing the floor with water, letting it dry, and then steam mopping again with a
clean pad. One or more rinses generally removes the residue. A more stubborn case may require you to rinse the
floor with a mixture of one part vinegar and two parts water.

11 When fini shed using your steam mop, press the STE AM CONTROL button until the light

returns to flashing blue. Unplug the mop and all ow it to cool for 2-3 minutes before storing.

12

When finished using your Handheld Steamer, release the steam trigger.
The STEAM CONTROL button LED will remain solid blue.
Unplug the Handheld Steamer and allow it to cool for 2-3 minutes before removing
the cleaning tools and storing.

S3901UK

S3901UK_QSG_150619

Paper: Quality A (Bright White) 157g/m2
Coating: Matte both sides

OR

First attach the Accessory Hose by pr essing the Nozzle
base onto the Handheld Steamer unt il it clicks into place .

Slide the All-Purpose Sc rubbing Pad over the Flat
Scrubber Tool. DO NOT use the Flat Scrub ber Tool
without the All-Purpose S crubbing Pad attach ed.

Press the Flat Scrubber Tool onto the Accessor y
Hose until it clicks into place.

DIRECT STEAM NOZZLE

For spot cleaning and direct ste aming

FLAT SCRUBBER TOOL

Cleaning countertops, a ppliances and
other above floor surfaces

CUSTOM CLEANING TOOL HOW TO ATTACH

Your Handheld Steamer can be used to clean, san itise and freshen many of your
above floor surfaces. Follow the quic k steps below to get started.

SQUEEGEE TOOL

Cleaning windows and glass surf aces

GROUT SCRUBBER TOOL

Removing stubborn messes in ha rd-to-reach
nooks, corners and in grout

Slide Nozzle base directly o nto the Handheld Steamer.

Attach the Window Squeeg ee by snapping into the hand le
of the Accessory Hose.

Select either LO, MED or HI mode by p ressing the ON/STE AM
SETTING button and wait unti l the selected set ting indicator
light turns solid blue. Hold do wn the
steam trigger to start stea ming.

Attach the Grout Scrubber by sn apping into the handle
of the Accessory Hose.

Select either LO, MED or HI mode by p ressing the ON/STE AM
SETTING button and wait unti l the selected set ting indicator
light turns solid blue. Hold do wn the steam trigger t o start
steaming.

S3901