Shark GS500 Series User Manual

garment care system

User’s Guide

GS500 series

IMPORTANT SAFETY INSTRUCTIONS

For Household Use Only

WHEN USING YOUR SHARK®
PRESS & REFRESH™ GARMENT
CARE SYSTEM, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS
BE FOLLOWED, INCLUDING THE
FOLLOWING:

READ ALL INSTRUCTIONS BEFORE
USING YOUR PRESS & REFRESH™
GARMENT CARE SYSTEM.

DANGER OF SCALDING

Please use caution when using the
garment steamer. The Wrinkle Eraser™
pressing bar and the steam emitted are very
hot. The Wrinkle Eraser™ is not controlled by
the steam trigger and is hot as long as the
unit is turned on and for 30 minutes after the
unit has been turned off.

IMPORTANT:

This appliance is not intended for use by
persons with reduced physical, sensory or
mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of
the appliance by a person responsible for
their safety.

Children shall not use or play with this
appliance. Close supervision is necessary to
keep appliance and its cord out of reach of
children during use and cooling.

WARNING:

TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY:

1. Use the system only for its intended use.

2. DO NOT use outdoors.

3. DO NOT leave the appliance unattended when
plugged in. Always unplug the power cord from
the electrical outlet when not in use and before
servicing.

4. DO NOT allow the appliance to be used by
children. Close attention is necessary when used
near children, pets, or plants.

5. Use only as dscribed in this manual.

6. Use only manufacturer’s recommended
accessories.

7. DO NOT use with damaged cord or plug.

8. DO NOT USE the appliance is not working, has
been dropped, dropped into water, damaged,

left outdoors, or if it is leaking.

9. NO SERVICEABLE PARTS. Incorrect re-
assembly or repair can cause a risk of electrical
shock or injury to persons when the appiance is
used. Contact Customer Service.

10. To protect against a risk of electric shock, DO
NOT immerse the garment steamer into water or
any other liquids.

11. DO NOT handle plug or garment steamer with
wet hands or operate appliance without shoes.

12. DO NOT pull or carry by power cord, use power
cord as a handle, close a door on the power
cord, or pull the power cord around sharp
corners or edges. Keep power cord away from
heated surfaces.

13. ALWAYS unplug the power cord from the
electrical outlet when filling or emptying the
water tank and when not in use.

2

1-8 00 -79 -739 8

14. NEVER attempt to fill this unit under a water
faucet. Always use the filling flask that is
provided.

15. DO NOT unplug by pulling on the power cord.
To unplug, grasp the plug not the power cord.
Do not use extension cords or outlets with
inadequate currect carrying capacity.

16. DO NOT put any objects into openings. Do not
use with any opening blocked.

17. This appliance and the accessories become hot
during use and surfaces may also become hot.
Exercise care when changing accessories and
follow removal and changing instructions as
outlined in the manual. Do not change frames
while the unit is turned on. Turn the unit off,
wait for the Wrinkle Eraser
change frames.

18. The garment steamer can be used in a vertical
or horizontal motion. NEVER hold the steam
head down while at rest or tilt it in a backward
position as this may result in discharge. When
using the appliance, it must be rested on a
stable surface.

19. DO NOT use on leather, suede, vinyl, plastic or
other delicate steam sensitive materials. Always
determine the colorfastness of any fabric before
using the garment steamer by testing it on a
small portion of the garment’s underside.

20. NEVER attempt to steam clothing while it is
being worn.

21. DO NOT add cleaning solutions, scented
perfumes, oils, or any other chemicals to the
water used in this appliance as this may damage
the unit or make it unsafe for use. If you live in a
hard water area, we recommend using distilled
water in your garment steamer.

22. When in use, NEVER turn the appliance
over or on its side. NEVER DIRECT STEAM
TOWARDS PEOPLE, ANIMALS OR PLANTS.
The steam is very hot and can cause burns.
Burns can occur from touching hot metal parts,
steam, steam bonnets or frames.

™

to cool, and then

23. Use care when you turn a steam appliance
upside down - there may be hot water in the
reservoir.

24. Let the system cool completely before putting
away. Loop cord loosely around the appliance
when storing.

25. When cleaning the garment steamer, unplug the
power cord from the electrical outlet and clean
with a dry or damp cloth. Do not pour water
or use alcohol, benzene or paint thinner on the
unit. :

26. Keep your work area well lit.

27. Store the garment steamer indoors in a cool, dry
place.

28. To avoid circuit overload, do not operate another
appliance on the same socket (circuit) as the
garment steamer.

29. If an extension cord is absolutely necessary, an
extension cord rated a minimum of 15 ampere,

2

2.08mm

cord should be used. Cords rated for
less amperage may overheat. Care should be
taken to arrange cord so that it cannot be pulled
or tripped over.

30. DO NOT leave your Garment Steamer
unattended when the system is connected to a
power supply/electrical outlet.

31. Always unplug and allow the garment steamer
to cool before removing or changing frames or
bonnets.

32. Make sure that the water tank door is closed
when using the appliance.

SAVE THESE
INSTRUCTIONS

3

Welcome to the next wave of garment care!

The Press & Refresh™ Garment Care System brings your fabrics back to life with fewer trips to the
dry cleaners! For the first time ever professional steam power in a portable unit.

The professional steam deeply penetrates fibers, renews and freshens fabric. The exclusive heated
Wrinkle Eraser™ presses for a crisp finish and dries fibers to prevent re-wrinkling.

Extend the life of your garments and go from not quite ready-to-wear to ready-to-wear in one easy step.
The Look Your Best Guide provides step-by-step tips for all of your garment care needs.

Attaching the appropriate
accessory:

The unit comes assembled with a
small steam bonnet attached. The
bonnet must be attached at all
times when the unit is being used.

1 Attach the desired frame

2 Using both hands, hold the

frame on either side. Attach
the top of the frame to the
unit above the Wrinkle Eraser™

FRAME/ACCESSORY

Small Steam Bonnet

Bristle Brush Frame

Upholstery/Delicate
Fabric Frame & Delicate Steam Bonnet

3 To remove the frame, gently

into the notch. Next, secure
the pointed end of the frame
around the bottom of the unit
and snap into place. (Fig. 1)
The seam of the frame must
line up against the seam of the
unit for proper use.

pull on the pointed end and lift
the frame off the unit.

Fig. 1

TIP: Wipe away condensation

from the steam guard on the
bottom of the frame after
extended use.

Upholstery/Delicate
Fabric Frame & Upholstery Steam Bonnet

4

1-8 00 -79 -739 8

Fig. 2

Helpful Tips on using the
Vertical Press Pad and VELCRO®
Clips:

1 For the first time ever, the

vertical press pad eliminates the
need for an ironing board. It is
designed to fit on any size door,
and can remain setup for your
convenience. The VELCRO
are used to position & stretch

USE FOR

The bonnet should always be attached
during any use and with any frame

Best for: cotton, wool, linen, denim

Best for: bedding, mattress, curtains,
baby bedding, plush toys, high chairs,
car seats, sofa and arm chairs

®

clips

the garment for quick steaming
with better results to complete
the garment care system .
(Fig. 2)

2 To make pressing easier, the

vertical press pad has two hooks
on either end to hang your
garment from for larger pressing
surface.

BENEFITS

The specially designed multi layered
honeycomb pad protects fabrics from
water marks and water impurities

Improves steam penetration on heavy
fabrics without leaving water marks

Specifically designed to protect delicate
fabric from high heat

Best for: lace, velvet, silk, satin,
embelished or delicate garments

Shaggy material acts like multiple fingers to
pick up dust and deodorise while steaming. It
provides a large pocket of hot steam

5

This appliance complies with the WEEE-Directive 2002/96/EC on the disposal of electrical and electronic
equipment (WEEE).

This appliance complies with the European directives for electromagnetic compatibility (EMC) 2004/108/EC and
its revisions, as well as Low Voltage Directive (LVD) 2006/95/EC and its revisions.

This marking indicates that this product should not be disposed with other household wastes
throughout the EU. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material
sources. To return your used device, please use the return and collection systems or contact the
retailer where this product was purchased. They can take this product for environmental safe
recycling.

This manual covers model number:

GS500***** 11

TECHNICAL SPECIFICATIONS

Voltage: 220-240V~, 50/60Hz.

Power: 1580 W

Water Capacity: 200 mL (6.5 fl. oz.)

6

1-8 00 -79 -739 8

IPX4

Contents

Thank you
for purchasing
the Shark®
Press & Refresh™
Garment Care
System.

Getting Started 8

Assembly of the Vertical Press Pad 9

Using your Press & Refresh™ 10

Care of your Press & Refresh™ 13

Troubleshooting Guide 13

7

Getting Started

The Press & Refresh™ Garment Care System provides a complete process for all of your garment
care needs. Save time and money with fewer trips to the dry cleaners and have your garments ready-to­wear when you want.

The combination of professional steam power and the exclusive heated Wrinkle Eraser™ makes it easier
than ever to care for your garments. The Press & Refresh
garment care needs. The vertical press pad eliminates the hassle of an ironing board and makes it easy
to steam and press right on the hangers.

Not only great on garments, the Press & Refresh™ can be used to refresh fabrics throughout your
home. Now you can easily reduce odors, sanitise fabric and help eliminate dust mites.
The extra long 15 foot power cord makes it easy to navigate around your home.

™

comes complete with accessories for all

a

c

b

d

e f

First things first, you need to
know what’s in the box you
just opened:

a Garment Steamer
b 2 Small Steam Bonnet ( P117W )

(one is attached to the unit)

c Bristle Brush Frame (1059 SO)
d Upholstery/Delicate Fabric

Frame (1060 SO)

e Upholstery Steam Bonnet

(P 116W )

f Delicate Steam Bonnet ( P121W)

8

1-8 00 -79 -739 8

g

h i

g Vertical Press Pad
h 2 Support Rods (assembled in

the vertical press pad)

i Garment Hook
j 8 Heat Protection Panels

(assembled in vertical press
pad)

k 3 VELCRO

®

Clips (103 9SO)

l Filling Flask (1057SO)
m Accessor y Bag (not shown)

VELCRO® is a registe red trademark of
Velcro Industries B.V.

j

k

l

IMPORTANT: Always check

the fabric care labels for
recommendations. Test the
fabrics for colorfastness in an
inconspicuous place such as
an inside seam. Some articles
of clothing are better steamed
from the underside.

IMPORTANT: When

assembling your garment
steamer, there may be a little
water in the water tank. This
is because we test all our
garment steamers 100%
before you buy them, so you
get a quality Shark® Steam
product.

Assembly of the Vertical Press Pad

Fig. 1

The straps can be adjusted
to fit any door using the
buckle to adjust the strap
lengths.

Fig. 2

Assembly & use instructions:

1 Remove contents of the Press &

Refresh™ Garment Care System
and lay them out on a flat
surface to see that you have all
the components to complete
the assembly.

2 READ ALL INSTRUCTIONS

BEFORE USING YOUR PRESS
& REFRESH™ GARMENT CARE
SYSTEM.

IMPORTANT: Always make

sure the garment steamer is
UNPLUGGED from the electrical
outlet when not in use. Never
fill the water reservoir when the
unit is plugged in.

Assembling the vertical
press pad:

3 Insert the garment hook into

the opening at the top of the
vertical press pad. (Fig. 1)
Secure the rod into the garment
hook on either side of the pad
making sure they are inserted
firmly. (Fig. 2) The support rods
come assembled in the pad.

4 The Vertical Press Pad comes

asembled with heat protection
panels in the pockets on the
back. These panels protect your
door from heat damage and
should be in place at all times
during use.

Fig. 3

5 Attach the vertical press pad to

any door. With the door open,
loop the straps at the top of the
vertical press pad around the
corner of the door and repeat
on the opposite side. Gently
tug on the pad to make sure
it is secure and shut the door
completely to ensure the pad is
stable for pressing. Be careful
not to close the door on your
fingers. Adjust the straps to the
appropriate height for comfort.
(Fig. 3)

Care instructions:

6 Remove the 8 heat protection

panels from the back of the
pad and remove the garment
hook and rods. Machine wash
in warm water with liquid
detergent and lay flat to dry.
Do not use bleach or fabric
softener.

9

Using Your Press & Refresh

™

Practice makes perfect!
It takes time to master
the garment steaming
techniques.

Fig. 1 Fig. 2

Filling and refilling the water
reservoir:

1 Never fill the garment steamer

while it is plugged into an
electrical outlet.

2 Open the water cap and hold

the the garment steamer
horizontally with the Wrinkle
Eraser™ parallel to the floor.
Using the filling flask provided
fill the water tank to the Max
Fill line. Be careful not to
overfill. Push the cap back into
place, making sure it closes
firmly. (Fig. 1)

NOTE: The water tank does not

have to be completely full for
the fabric steamer to generate
steam. However, make sure
that the water tank is at least
half way full for optimal results.

For best results, tilt the
steamer forward slightly
and press the wrinkle
eraser directly on the
garment.

The seam on the frame must line up
with the seam on the unit for proper
use and safety. The frame will snap into
place, double check to make sure the
seams are aligned.

Attaching the accessories:

IMPOR TAN T: Use caution

when changing the frames
when the unit is hot. The
frames are designed with a
steam guard around the bottom
to provide protection from heat
when placing or removing the
frames.

The small steam bonnet must

be attached at all times during
usage.

The bonnet should only be

removed for washing by hand,
if necessary (see page 13 for
care instructions).

3 Choose your desired frame.

Using both hands, hold the
frame on either side. Attach
the top of the frame to the

Fig. 3

Fig. 4

unit above the Wrinkle Eraser™
into the notch. Next, secure
the pointed end of the frame
around the bottom of the unit
and snap into place. (Fig. 2)

When using the upholstery/
delicate fabric frame:

NOTE: Remember, DO NOT use

the garment steamer without
the small steam bonnet in place

4 Attach the desired bonnet to

the frame, then attach the
frame to the unit. Pull either
side of the bonnet over the top
of the frame and secure the
bottom of the bonnet to the
frame. (Fig. 3) Then attach the
frame to the garment steamer
as described above. (Fig. 4)

10

1-8 00 -79 -739 8

Hold the steam trigger
for continuous steam.
The steam will stop
emitting once you let
go of the button.

Wipe away condensation
from the frame with
extended use.

Using the Press & Refresh

™

and

vertical press pad:

CAUTION: The Wrinkle Eraser™

is not controlled by the steam
trigger and is hot as long as the
unit is turned on.

CAUTION: Do not over tilt the

unit when steaming overhead.

CAUTION: Do not hold the

unit in a fixed position on
delicate fabrics and upholstered
items.

CAUTION: The Wrinkle Eraser™

is hot. Use caution when
removing the frames. DO NOT
put your hands directly onto the
Wrinkle Eraser™.

WARNING: Never steam any

article of clothing while it is
being worn.

1 Hang the vertical press pad on

a door.

2 Hang the garment onto the

garment hook.

3 Once the selected attachment

is placed on the garment
steamer, turn the On/Off switch
to the “I” position, a blue LED
light will illuminate. It will take
approximately 1 minute for the
unit to heat up.

4 Holding the garment steamer

in the vertical position with the
steam nozzle pointing away
from you, press and hold the
steam trigger for continuous
steam and begin steaming your
garments in a vertical motion.
Begin at the top of the garment
and move in a up and down
direction pressing the Wrinkle

™

directly onto the fabric.

Eraser

5 You can use the hooks on either

side of the vertical press pad for a
larger pressing area.

6 When steaming lightweight

garments, the VELCRO® clips
can be used in place of a
hanger to attach a garment
directly to the pad.

7 When finished using the

garment steamer, turn the
appliance “O” and let it cool
before emptying the water tank
and removing the bonnets and
frames if necessary.

Using the Press & Refresh™
horizontally:

8 The Press & Refresh™ can be

used to deodorise, sanitise and
refresh upholstered items: sofa,
baby bedding, mattress, car
seat, drapes, and more.

9 Attach the upholstery/delicate

frame and upholstery steam
bonnet to the unit.

10 In a horizontal position, move

the steamer in a up and down
motion continuously over the
upholstered item.

11

Using Your Press & Refresh™ - cont.

When to use the different
accessories:

1 Small Steam Bonnet – must

be in place over steam nozzle
during all usage.

TIP: Provides evenly distribution

of steam and protects fabrics
from watermarks and impurities
in water

2 Bristle Brush Frame – Offers

better steam penetration for
heavy fabrics without leaving
water marks.

Fabric Recommendations:

Heavy fabrics, cotton, wool,
canvas, denim.

CAUTION: Do not use the

bristle brush on delicate fabrics.

3 Upholstery/Delicate Fabric

Frame & Delicate Steam
Bonnet – provides extra

protection for delicate fabrics
when the Wrinkle Eraser

™

is
not necessary while freshening
fabrics.

Fabric Recommendations:

Silk, satin, embellished
garments.

TIP: Some garments have

better results when steamed
from the inside or turned inside
out. Slightly tug the bottom
of the garment and hold at an
angle.

4 Upholstery/Delicate Fabric

Frame & Upholstery Steam
Bonnet – shaggy material acts

like multiple fingers to pick
up dust and deodorise while
steaming. It provides a large
pocket of hot steam.

5 VELCRO

®

Clips –

Easy detachable clips can
be used to hold lightweight
garments directly on to the pad
and to position & stretch the
garment for quick steaming
with better results

6 Vertical Press Pad –

Creates a vertical ironing board
anywhere in the home. The
Vertical Press Pad can be used
on any door and is virtually
invisible when the door is closed
for easy access to the pad for
last minute touch ups.

12

1-8 00 -79 -739 8

Care of Your Press & Refresh

™

Cleaning & storing

1 Turn the garment steamer off

“O ”.

2 Unplug the appliance from the

electrical outlet.

3 Let the appliance cool

completely for approximately
30 minutes.

4 Empty the water from the

water tank.

5 Wipe the exterior of the

garment steamer with a damp
cloth and wipe dry if needed.

6 Bundle up the power cord and

secure it with the VELCRO
strap that is attached to the
power cord. Always store your
appliance in a cool, dry area.

Care & use of the small steam
bonnet

7 The steam bonnet helps filter

impurities from your water.
It might become slightly
discolored over time.

8 Let the steamer cool completely

before removing the bonnet.
Gently pull on either side of
the bonnet to remove from the
steam nozzle.

®

Troubleshooting Guide

PROBLEM POSSIBLE REASONS SOLUTIONS

Verify that the blue light on the unit is lit. If not,
check that the unit is plugged in and the on/off
button is raised and in the on “I” position.

Verify that the water tank is at least half way full
or fill to the max fill line.

There is no
steam.

The steamer is not turned on.

There is not enough
water in the unit.

9 Hand wash the bonnet in cold

water with a mild detergent and
let air dry completely before
using again. Do not dry in
clothes dryer.

10 To re-attach the bonnet, pull

one corner of the bonnet over
the steam nozzle then the other
corner. Secure the bottom of
the bonnet to the nozzle using
the bottom tab.

The nozzle leaves
water drops on the
garment.

You are not using the steam
bonnet.

The steam bonnet is
too wet.

The frame has condensation.

The small steam bonnet must be in place
at all times during usage.

The bonnet prevents water drops being left on
the garment and to removes impurities from your
water.

Let the unit cool for 30 minutes, remove the
steam bonnet and let it dry out before using
again or replace with a new bonnet.

Let the appliance cool and wipe the frame off.

13

Notes

14

1-8 00 -79 -739 8

Notes

15

EURO-PRO Operating LLC
180 Wells Avenue Suite 200, Newton MA 02459
United States of America

1-800 -798 -739 8

Technical Details
Model number: GS500***** 11
Input: 1580 Wat ts

Main unit voltage: 220-240V~, 50/60Hz

COPYRIGHT© EURO- PRO OPERATIN G LLC 2014

PRINTED IN CHINA

Euro- Pro, Wrinkle Era ser, Press & Refresh, and Shark are trademarks
of Euro- Pro Operatin g LLC. All other brand names may be trademarks
of their respective owners.

GS500*****11. E.14 0604.1

Illustrations may differ from actual product.

IPX4