Shark CORDLESS 3-in-1 Quick Start Guide
CORDLESS 3-IN-1 EMPTYING THE DUST CUP
1
Please make sure to read the enclosed Shark® Owner’s Guide prior to using your vacuum.
UPRIGHT
The brushroll is activated when the hand vacuum
is connected and powered on, and the handle is
tilted back.
ABOVE-FLOOR
HA ND VACU U M
To detach the hand vacuum, press the release
buttons on both sides of the handle and lift it o
the wand . Attach an accessory by sliding it into
the nozzle. To remove the accessory, press the
release buttons on the handle.To reattach the hand
vacuum , slide the nozzle over the wand on until it
clicks into place.
With the power o, slide the release button forward,
and the dust cup will swing open. Tap the dust screen
lightly to knock o dust and debris.
2
Wipe dust screen lightly with a dry cloth to remove
dust and dirt.
CORDLESS 3-in-1
QUICK
START
GUIDE
WA N DVAC
SYSTEM
PET
™
ABOVE-FLOOR
WAND
To detach the floor nozzle, step on the nozzle
while pressing the release button at the bottom of
the wand . Lift the wand to remove it. Reattach by
sliding the wand over the nozzle neck until it clicks
into place.
© 2020 Sh arkN inja Operating LLC . SHA RK is a registered trad emark of Sha rkNinja Operatin g LLC.
WANDVAC is a trade mark of SharkNinja Operating L LC.
WS632Series_QSG_ MP_Mv2
For questions, visit us online
at sharkclean.com/support
Register your vacuum at
registeryourshark.com
WS632 Series
WHAT’S INSIDE: POWER SETTINGS
A
Hand Vacuum
B
Wand
C
PowerFins Floor Nozzle
D
WANDVAC™ System Docking Station
E
Battery Pack
F
Hand Vacuum Storage Clip
G
Duster Crevice Tool
H
Pet Multi-Tool
AS SE MB LY
A
2
(Click)
E G
1. Slide the wand onto the neck of the floor nozzle
2. Slide the hand vacuum nozzle over the wand
3. Make sure the dock plate is facing upright. Slide
4. Place the dock on the floor near a wall outlet.
5. Store cleaning accessories on the mount on
For proper operation, ensure all components are
completely connected and clicked into place.
F
until it clicks into place.
until it clicks.
the charging post into the slot on the back of
the dock until it clicks into place.
Plug the wall charger into the outlet, then
connect the cord to the port on the back of the
charging post.
the dock plate.
H
POWER BOOST MODE
Press the On/O button on the handle to turn on
B
power. To turn o power, press the button again.
1
For an added boost of power, push and hold the
Boost button on the handle. The Boost icon will
blink white while in this mode. Release the button
to return to standard power.
(Click)
LI-ION BATTERY
Charging
C
In Use
3
(Click)
D
4
(Click)
Low
Charge
1
Mid
Charge
Nearly
Full
Full
Charge
CHARGING OPTIONS
2
Full
Charge
Mid
Charge
Low
Charge
3
Nearly
Empty
No
Charge
Boost
STORAGE ON THE GO
To store the hand vacuum on the wand, slide it
onto the storage clip on the wand, with the filter
removal latch on the back of the hand vacuum
sitting inside the clip.
5
Accessory
Storage
For complete maintenance instructions, see the
enclosed Owner's Guide.
For additional parts and accessories, visit
sharkaccessories.com.
For additional batteries and charging accessories,
visit sharkclean.com/batteries.
UPRIGHT DOCK CHARGING
Make sure the contacts on the wand or hand vacuum are aligned with the contacts on the charging post.
When docked properly, the charging lights on the ha nd vacuum will blink, indicating that charging has begun.
When charging is complete, all three indicator lights will illuminate steadily, and then shut o after 10 minutes.
SIDE-BY-SIDE STORAGE
CHARGING HAND VACUUM
Loading...