Shark AV1010AE User Manual

Robot Vacuum

AV1010AE Series

OWNER’S GUIDE

IMPORTANT SAFETY INSTRUCTIONS

PLEASE READ CAREFULLY BEFORE USE • FOR HOUSEHOLD USE ONLY

If the charging cable plug does not ﬁt fully into the outlet, reverse the plug. If it still does not ﬁt, contact a qualiﬁed electrician. DO NOT force into outlet or try to modify to ﬁt.

WARNING

To reduce the risk of ﬁre, electric shock, injury, or property damage:

GENERAL WARNINGS

When using an electrical appliance, basic precautions should always be followed, including the following:

1. Robotic vacuum cleaner consists of a

QUICK

robotic vacuum and charging base with power supply. These components contain

START

electrical connections, electrical wiring, and moving parts that potentially present risk to the user.

GUIDE

2. Before each use, carefully inspect all parts for any damage. If a part is damaged, discontinue use.

3. Use only identical replacement parts.

4. This robotic vacuum cleaner contains no

serviceable parts.

5. Use only as described in this manual. DO NOT use the robotic vacuum cleaner

for any purpose other than those described in this manual.

6. With the exception of ﬁlters, DO NOT expose any parts of the robotic vacuum cleaner to water or other liquids.

USE WARN ING S

7. This appliance can be used by persons

with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. a) Children shall not play with the

b) Cleaning and user maintenance shall

8. Always turn o the robotic vacuum

9. DO NOT handle plug, charging base,

appliance.

not be made by children without supervision.

cleaner before inserting or removing the ﬁlter or dust bin.

charging cable, or robotic vacuum cleaner with wet hands. Cleaning and user maintenance shall not be made by children without supervision.

10. DO NOT use without robot dust bin and ﬁlters in place.

11. DO NOT damage the charging cord:

a) DO NOT pull or carry charging base

by the cord or use the cord as a handle.

b) DO NOT unplug by pulling on cord.

Grasp the plug, not the cord.

c) DO NOT close a door on the cord,

pull the cord around sharp corners, or leave the cord near heated surfaces.

12. DO NOT put any objects into nozzle or accessory openings. DO NOT use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air ﬂow.

13. DO NOT use if robotic vacuum cleaner airﬂow is restricted. If the air paths become blocked, turn the vacuum cleaner o and remove all obstructions before turning on the unit again.

14. Keep nozzle and all vacuum openings away from hair, face, ﬁngers, uncovered feet, or loose clothing.

15. DO NOT use if robotic vacuum cleaner is not working as it should, or has been dropped, damaged, left outdoors, or dropped into water.

16. DO NOT place vacuum cleaner on unstable surfaces.

17. DO NOT use to pick up:

a) Liquids b) Large objects c) Hard or sharp objects (glass, nails,

screws, or coins)

d) Large quantities of dust (drywall

dust, ﬁreplace ash, or embers). DO NOT use as an attachment to power tools for dust collection.

e) Smoking or burning objects (hot

coals, cigarette butts, or matches)

f) Flammable or combustible

materials (lighter ﬂuid, gasoline, or kerosene)

g) Toxic materials (chlorine bleach,

ammonia, or drain cleaner)

18. DO NOT use in the following areas: a) Wet or damp surfaces b) Outdoor areas c) Spaces that are enclosed and may

contain explosive or toxic fumes or vapors (lighter ﬂuid, gasoline, kerosene, paint, paint thinners, mothprooﬁng substances, or

ﬂammable dust) d) Near ﬁreplaces with unobstructed entrances. e) In an area with a space heater.

19. Turn o the robotic vacuum cleaner

before any adjustment, cleaning, maintenance or troubleshooting.

20. Allow all ﬁlters to air-dry completely

before replacing in the robotic vacuum cleaner to prevent liquid from being drawn into electric parts.

21. DO NOT modify or attempt to repair the

robotic vacuum cleaner or the battery yourself, except as indicated in this manual. DO NOT use the vacuum if it has been modiﬁed or damaged.

22. To reduce the risk of electric shock, this

appliance has a polarized plug (one blade is wider than the other). This plug will ﬁt in a polarized outlet only one way. If the plug does not ﬁt fully in the outlet, reverse the plug. If it still does not ﬁt, contact a qualiﬁed electrician to install the proper outlet. Do not change the plug in any way.

23. In case the self-empty base has a

thermal shuto the unit needs to have a hard power reset to restart.

BAT T E RY U S E

24. The battery is the power source for

the vacuum. Carefully read and follow all charging instructions.

25. To prevent unintentional starting, ensure

the vacuum is powered o before picking up or carrying the vacuum. DO NOT carry the appliance with your ﬁnger on the power switch.

26. Use O N LY the Shark ® self-empty base

XSKAEDOCK and use only battery RVBAT850. Use of batteries or battery chargers other than those indicated may create a risk of ﬁre.

SAVE THESE INSTRUCTIONS

For the latest warnings and cautions, go to sharkclean.com/robothelp

27. Keep the battery away from all metal objects such as paper clips, coins, keys, nails, or screws. Shorting the battery terminals together increases the risk of ﬁre or burns.

28. Under abusive conditions, liquids may be ejected from the battery. Avoid contact with this liquid, as it may cause irritation or burns. If contact occurs, ﬂush with water. If liquid contacts eyes, seek medical help.

29. Robotic vacuum cleaner should not be stored, charged, or used at temperatures below 50°F (10°C) or above 104°F (40°C). Ensure the battery and vacuum have reached room temperature before charging or use. Exposing the robot or battery to temperatures outside of this range may damage the battery and increase the risk of ﬁre.

30. DO NOT expose the robotic vacuum cleaner or battery to ﬁre or temperatures above 265°F (130°C) as it may cause explosion.

31. Non-rechargeable batteries cannot be recharged.

BOTBOUNDARY® STRIPS

32. DO NOT put BotBoundary strips

underneath carpet or rugs.

33. DO NOT place BotBoundary strips on top of one another.

34. Always use BotBoundary strips around reﬂective ﬂooring and surfaces.

35. BotBoundary strips should always be used near carpeted stairs.

36. DO NOT place BotBoundary strips within 10 feet of the dock.

37. For your robot’s cli sensors to work properly, all runners, rugs, or carpets must be eight inches from any stairs (or it must be continuous and extend over the edge of the stairs). If a runner, rug or carpet edge that is less than eight inches from the stairs cannot be moved, you must use a BotBoundary strip to block o the stairs.

sharkclean.comsharkclean.com

GETTING TO KNOW YOUR SHARK IQ ROBOT® GETTING TO KNOW YOUR SHARK IQ ROBOT®

Front Bumper

Clean Button

Dust Bin

Release Tabs

Debris Discharge

Opening

Charge Indicator Lights

Error Indicator Light Wi-Fi Indicator Light

Docking Sensor

Dock Button

Navigation

Module

Power Button

Base Dust Bin Release

Fill Window

Base Dust Bin

Post-Motor Filter Access Door

Debris Intake

Charging Contact

FRONT

Pre-Motor

Filter Housing

Charging Base

Charging Contact

BACK

Dust Bin Release

Side Brush

Battery Door

Vision Module

Charging Contact

Cli and Boundary Sensors

Front Caster

Wheel

Drive Wheel

Brushroll Door

Robot Dust Bin

and Filter

Pre-Motor Filter Access Door

Charging Base

Power Cord

Wrap

Base Dust Bin

Post-Motor Filter

Access Door

Power Switch

sharkclean.comsharkclean.com

3 ft.

BASE SETUP

CHARGING

IM P ORTA N T: The Shark iQ Robot® has a pre-installed rechargeable batter y. Battery should be fully charged

before using. It may take up to 6 hours to fully charge.

5 ft.

3 ft.

SharkMat

(for use on carpet)

The Self-Empty Base charges your robot and holds dirt and debris from up to 30 days of cleaning. Select a permanent location for the base, because ever y time you relocate it, your robot will be required completely re-map your house.

Choose a level surface in a central area. Remove any objects that are closer than 3 feet from either side of the base, or closer than 5 feet from the front of the base. Plug in the Charging Cord, and turn on power switch on the back of the base, then place the base with its back against the wall, in an area with a good Wi-Fi signal. For best results, set up base on bare ﬂoor, or on the SharkMat. The base must be plugged in continuously for the robot to ﬁnd it. The Indicator Light will illuminate green when the base has power.

NOTE: For best resu lts, set up on ba re ﬂoor o r thin ca rpet.

NOTE: Do no t place base against baseboa rds, heating e lements, or in direc t sunlight.

NOTE: Every time the robot returns to the base, it makes a loud noise as it empties its debris. This is normal and should not

be a cause of concern.

INSTALLING THE SIDE BRUSHES

Snap the 2 included Side Brushes onto the square pegs on the bottom of the robot.

To charge, the Power button on the side of the robot must be in the ON position (I). The robot will beep when charging begins.

Clean Dock

When the cleaning cycle is complete, or if the battery is running low, the robot will search for the base. If your robot doesn’t return to the base, its charge may have run out.

If the robot has no charge and cannot return to the base, manually place it on the base. The base indicator light will ﬂash blue and the robot will beep when charging begins.

NOTE: Whe n manu ally placing th e robot on the base, make su re the Charging Contacts on the bottom of the robot are touching the ones on the base and the robot's dust bin is touching the de bris int ake on the base. While the robot is charging, both blue LED light s will ﬂa sh. Wh en char ging is complete, both bl ue lights will illumin ate steadily.

NOTE: Whe n picki ng up the ro bot be careful not to place ﬁngers between the bumper and the base of the robot.

sharkclean.comsharkclean.com

CHARGE INDICATOR LIGHTS

In Use

While Charging (Blue)

Full

Charge

(Blu e)

Partia l

Charge

(Blu e)

Low

Charge

(Red)

BUTTONS AND INDICATOR LIGHTS

CHARGE INDICATOR LIGHTS

Display the amount of charge remaining in the battery.

No Charge or O

The blue indicator lights on the robot show how much charge is remaining. While the robot is charging, both blue LED lights will ﬂash. When charging is complete, both blue lights will

illuminate steadily. It may take up to 6 hours to fully charge your robot.

CLEAN BUTTON

Press to begin a cleaning session. Press again to stop.

RECHARGE & RESUME

Press and hold the CLEAN button for 15 seconds to turn Recharge & Resume ON or OFF.

The Recharge & Resume function is turned OFF by default. Turn ON Recharge & Resume for complete coverage if your home's ﬂoor plan is bigger than 1800 sq. ft. Your robot will return to the base, recharge, and can pick up cleaning where it left o.

“!” ERROR INDICATOR

See Troubleshooting section for full list of error codes .

WI-FI INDICATOR

Blue light: connected to Wi-Fi.

Red light: not connected. Flashing blue: setup mode. No light: not set up yet.

NAVIGATION MODULE

Please keep clear and do not cover.

Upward-facing sensor aids advanced navigation.

DOCK BUTTON

Press to stop cleaning and send robot back to the charging base.

EVACUATE & RESUME

Press and hold the DOCK button for 15 seconds to turn Evacuate & Resume ON or OFF.

Turn ON Evacuate & Resume for homes with pets . Your robot will return to the base to empty the dust bin after 30 minutes, then resume cleaning where it left o.

NOTE: If the low charge light is blink ing red , there is not eno ugh cha rge for the robot to return to th e base. M anua lly place th e robot on the base.

NOTE: If you r ﬂoor plan is sm aller than 10 00 sq. f t., we recomm end tha t you DO NOT u se the Evacuate & Res ume function.

sharkclean.comsharkclean.com

+ 10 hidden pages