Shark 100T Quick Start Manual

Shark® 100T Quickstart

Electro Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

Electro Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

5.02”

[12.75cm]

3.25”

[8.26cm]

Ic Ib Ia

HI HI HI

LO LO LO

3.52”
[ 8.90cm]

0.62”
[1.61cm]

[12.10cm]

4.78"

[2.31cm]

0.91"

4.16”

[10.60cm]

DIN Installation

Release clip

100T
Dimensions

DIN Rail with black
rubber stoppers

lc

HI

LO

lb

HI

LO

la

HI

LO

Earth Ground

L(+)

Power
Supply
Connection

N(-)

L(+)

GND

N(-)

Vref

Va

Vb

Vc

LINE

LOAD

CT
Shorting
Block

FUSES
3 x 0.1A

FUSE

3A

C

C

B

B

A

A

N

N

lc

HI

LO

lb

HI

LO

la

HI

LO

Earth Ground

Earth Ground

L(+)

Power
Supply
Connection

N(-)

L(+)

GND

N(-)

Vref

Va

Vb

Vc

LINE

LOAD

CT
Shorting
Block

FUSES
3 x 0.1A

FUSE

3A

C

C

B

B

A

A

N

N

lc

HI

LO

lb

HI

LO

la

HI

LO

Earth Ground

Earth Ground

L(+)

Power
Supply
Connection

N(-)

L(+)

GND

N(-)

Vref

Va

Vb

Vc

LINE

LOAD

CT
Shorting
Block

FUSES
2 x 0.1A

FUSE

3A

C

C

B

B

A

A

WYE direct, 3

phase, 4 wire

Delta direct, 3

phase, 3 wire

lc

HI

LO

lb

HI

LO

la

HI

LO

Earth Ground

L(+)

Power
Supply
Connection

N(-)

L(+)

GND

N(-)

Vref

Va

Vb

Vc

LINE

LOAD

CT
Shorting
Block

FUSES
3 x 0.1A

FUSE

3A

C

C

B

B

A

A

Shark® 100T Quickstart Guide

Mechanical Installation

Installation Steps: Slide top of groove of meter onto DIN Rail. Press gently until the meter clicks into place. If

mounting with DIN Rail provided, use Black Rubber Stoppers (also provided) shown above.
To remove meter, pull down on Release clip

. Electrical Installation: Select diagram for your application.

NOTE: Other wiring configurations are available. See the full Manual on the enclosed CD.

WYE with PTs,

3 phase, 4 wire

Delta with PTs, 3

phase, 3 wire

Doc# E145704 V.1.10 QS - 1

Electro Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

Electro Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

RS485 Programming (for Ethernet see page QS-3)

Shark® 100T Quickstart

Communication Wiring: The Shark

uses standard 2-wire, half duplex architecture.

Factory Initial Default Settings: When the Shark 100T is powered

up, for 10 seconds you can connect to the meter using the Factory

Default Settings (even if the Device Profile has been changed). After

10 seconds the Device Profile reverts to the actual Device Profile in

use. This is one way you can always connect to the meter. The

Factory Initial Default Settings are:

Device Address:1

Baud Rate:9600

Protocol:Modbus RTU

Connection Steps:

1.Open Communicator EXT (download from product CD).

2.Click Connect on the tool bar. The Connect screen

opens. Make sure your settings match these (use pull-

down windows).

3.Click Connect. The Device Status screen confirms

the connection.

4.Click OK. Communicator EXT’s Main screen opens.

Configuration Steps:

5.Click the Profile button on the tool bar. The Device Profile screen opens.

6.Click the Communication tab and select settings based

on your application - RS485 ONLY, not INP10.

7.Click the Scaling tab and select settings based on your

application.

Communications Settings (RS485 ONLY, not INP10):

NOTE: The IrDA settings do not apply to the 100T.

COM2 (RS485): Enter the following settings:

Address (1-247)

Protocol (Modbus RTU, ASCII or DNP)

Baud Rate (9600 to 57600)

Response Delay (0-750 msec)

Scaling Settings (CT, PT Ratios and System Wiring):

Enter the following settings:

CT Numerator (enter value you want), Denominator (display only), Multiplier (1, 10, or 100), CT

Fullscale (Calculated automatically)

PT Numerator (enter value you want), Denominator (enter value you want), Multiplier (1, 10, 100, or

10000), PT Fullscale (Calculated automatically)

® 100T meter’s RS485 port

Doc# E145704 V.1.10 QS - 2