CITI RANGE - ASSEMBLY INSTRUCTION MANUAL
PRODUCT DESCRIPTION:CORNER WORKSTATION - SINGLE - 1 PERSON (1500 x 1500 x 750)
CODE/S: CTWS1515
CITI RANGE - ASSEMBLY INSTRUCTION MANUAL
IMPORTANT
Please read all instructions before beginning job.
These instructions are provided to avoid problems that may occur from improper assembly. The manufacturer
and/or distributor are not responsible for failure resulting from improper assembly or installation. Moreover, all
warranties are void for failure to follow these assembly instructions.
CAUTION
Under no circumstance must any form of abrasive be used as this will damage the surface. Do not use
solvents, solvent based cleaners, scouring pads, steel wool, furniture wax or scrubbing brushes.
As with all indoor furniture, this unit should not be exposed to direct sunlight, extreme temperatures or
moisture, as this can result in serious irrepairable damage.
Assembly of this furniture requires 2 people to complete the job safely.
This furniture is not designed to be used as a seat or as a ladder. Standing or sitting on this furniture presents
a serious risk to health and safety and will void the warranty.
NOTE:
When moving any furniture, always lift it, never drag it.
CITI RANGE - ASSEMBLY INSTRUCTION MANUAL
WORK TOP
END LEG
WORK TOP BRACKET
(OPTIONAL COMPONENT)
abfec
END-END BEAM
BEAM CONNECTOR
TELESCOPIC BEAM
d
INCLUDED PARTS
abeec
Beam Connector Beam Connector
Top Bracket
(Optional Component)
Telescopic Beam
Single End Leg
End to End Beam
1500W Top - 1362mm
x 2
x 6
x 6
x 3
x 2
M6 x 35mm
M6 x 25mm
M6 x 15mm
(Optional Component)
6G x 20mm
x 12
x 24
x 12
f
Work Top
1500 x 1500 x 750
x 1dM6 x 75mm
x 4
TOOLS REQUIRED
abcdPower Drill
Spirit Level
5mm Hex Drill Head Bit
Philips Drill Head Bit PH2eTape Measure
INSTRUCTIONS
1
FAMILIARISE YOURSELF WITH ALL THE COMPONENTS.
IT IS RECOMMENDED TO TAKE EACH COMPONENT OUT AND LAY IT OUT (WITH PACKAGING) AS
SHOWN IN THE DIAGRAM BELOW. THIS WILL MAKE IT EASIER TO CONSTRUCT THE WORKSTATION.
END LEG
END-END BEAM
BEAM CONNECTOR
WORKTOP BRACKET
(Optional Component)
1 x CITI WORKTOP
NOTE: IT IS RECOMMENDED TO CONSTRUCT THE WORKSTATION IN THE AREA IN WHICH IT IS TO BE USED.
TELESCOPIC BEAM
INSTRUCTIONS
2
FIX BEAM CONNECTORS TO BEAM IN 6 LOCATIONS
ENSURE THE BEAM IS UP THE RIGHT WAY WITH THE
SMALLER HOLES AT THE TOP
TOP OF BEAM HAS SMALLER HOLES
BOTTOM OF BEAM
HAS LARGER HOLES
BEAM
CONNECTOR
TOP OF BEAM CONNECTOR MUST
SIT LEVEL WITH TOP OF BEAM
SIDE VIEW
x 12
M6 - 35mm BOLT
M6 35mm
BOLT
3
THIS STEP IS IMPORTANT TO DETERMINE THE LOCATION
OF THE RETURN SECTION OF THE WORKTOP (LEFT OR
RIGHT)
LAY OUT THE BEAMS WITH THE CONNECTORS ATTACHED
(AS SEEN BELOW)
YOU WILL NOTICE THAT THERE ARE HOLES IN THE SIDE
OF THE BEAM.
RETURN TO BE POSITIONED ON RIGHT SIDE
RETURN TO BE POSITIONED ON LEFT SIDE
POSITION THE BEAMS ON THE GROUND ACCORDING TO
WHICH THE SIDE YOU WISH TO HAVE THE RETURN
POSITIONED ON (LEFT OR RIGHT)
INSTRUCTIONS
5A
ATTACH THE TELESCOPIC BEAMS TO THE MAIN FRAME &
END LEG
NOTE: THE RETURN BEAMS MUST SIT LEVEL WITH THE END-END BEAM.
TELESCOPIC BEAM
END-END BEAM
4
FIX END-END BEAMS TO END LEGS - (4 LOCATIONS)
NOTE: THE BEAM CONNECTOR
MUST SIT LEVEL WITH THE TOP
OF THE END LEGS
x 16
M6 - 25mm BOLT
M6 25mm
BOLT END LEG
BEAM CONNECTOR
END-END BEAM
x 4
M6 - 75mm BOLT
UNSCREW THE BOLTS (8 IN TOTAL) ON EITHER SIDE OF
THE TELESCOPIC BEAM.
DO NOT UNSCREW THEM ALL THE WAY OUT;
LOOSEN THEM ENOUGH TO MOVE THE BEAM ALONG THE
MIDDLE COMPONENT.
END LEG
NOTE: THE ABOVE IMAGE SHOWS A RIGHT RETURN BEING ATTACHED.
RIGHT RETURN
LEFT RETURN
FINISHED LENGTH - 834mm
5B
x 8
M6 - 25mm BOLT
M6 - 75mm
INSTRUCTIONS
7
FIX TOP BRACKETS TO END LEG (WITH TELESCOPIC BEAMS
ATTACHED) IN 2 LOCATIONS .
ENSURE THE BRACKET SITS LEVEL WITH THE LEG
TOP BRACKET
M6 -
15mm
BOLT
END LEG
x 4
M6 - 15mm BOLT
END LEG
6
NOTE: THIS STEP IS OPTIONAL - FOR THE MAIN DESK FRAME
FIX TOP BRACKET TO END LEGS IN 4 LOCATIONS ENSURE
THE BRACKET SITS LEVEL WITH THE LEG
TOP BRACKET
M6 -
15mm
BOLT
END LEG
x 8
M6 - 15mm BOLT
WORKTOP BRACKET
END LEG
TELESCOPIC BEAM
TELESCOPIC BEAM
INSTRUCTIONS
6G - 20mm
SCREW
CLOSE UP OF FIXING THROUGH BEAMS
9
NOTE: THIS STEP IS TO BE UNDERTAKEN IF YOU HAVE NOT
COMPLETED STEP 6.
FIX THE WORKTOP THROUGH END-END BEAMS &
TELESCOPIC BEAMS (AS SHOWN BELOW)
END-END &
TELESCOPIC BEAM
FLIP THE FRAME AND PLACE ONTO THE WORKTOP (AS
SHOWN BELOW)
THE WORKTOP SHOULD BE POSITIONED TO HAVE A 5MM
OVERHANG ON EACH SIDE.
x 12
6G - 20mm
SCREW
8
NOTE: THE STEP BELOW IS ONLY APPLICABLE IF YOU HAVE
COMPLETED STEP 6, IF NOT PROCEED TO STEP 9.
FIX THE WORKTOP TO THE FRAME THROUGH THE WORKTOP
BRACKET (4 LOCATIONS)
INSET IMAGE SHOWS A RIGHT RETURN
INSET IMAGE SHOWS A RIGHT
RETURN
UNDERSIDE OF WORKTOP
INSTRUCTIONS
11
FLIP THE DESK TO BE RIGHT SIDE UP.
IT IS IMPORTANT THAT THE WORKTOP SIT LEVEL.
PLACE THE LEVEL IN THE MIDDLE OF THE WORKTOP
(AS SHOWN BELOW)
IF ADJUSTMENT IS NEEDED WIND THE FEET ACCORDINGLY.
END LEG
ADJUSTABLE FOOT
DETAIL VIEW
10
WHILE THE FRAME IS STILL FACE DOWN, FIX THE
WORKTOP THROUGH THE WORKTOP BRACKETS ON THE
RETURN LEG.
(2 LOCATIONS)
x 6
6G - 20mm
SCREW
UNDERSIDE OF WORKTOP
RETURN END LEG
INSET IMAGE SHOWS A RIGHT RETURN
COMPLETE WORKSTATION
INSTRUCTIONS
CARE INSTRUCTIONS
•AVOID USING ABRASIVE CLEANERS.
•WORKTOPS AND FRAMES CAN BE CLEANED WITH A DAMP, SOFT CLOTH, THEN DRY THE SURFACE
COMPLETELY.
•IF MARKS OR SCUFFS ON WORKTOP OR FRAME OCCUR; WARM WATER WITH SOAP ON A DAMP CLOTH
CAN BE USED.
Loading...