SHANY SNVR-8004ST-1 User Manual

Network Video Recorder

SNVR-8004ST-1

Thanks for purchasing our product. Before operating the unit, please read the instructions

carefully and keep this manual for future reference.

Statement:

 This manual supports NVR model: 1U 4/8ch and 2U16/32ch.
 As product update, the NVR functions might be different from the manual showing, please

follow the product that you got.

Safety Precautions

1. Do not use wet hands or any damp objects to touch the power switch and network digital

video recorder (NVR), in order to avoid electric shock.

2. After installing the host, it must be ensured that the host and the chassis have grounded to

avoid the video, audio signal being disturbed, and to avoid NVR being damaged by static
electricity.

3. The device does not include hard disk. Hard disk should be properly installed before use,

otherwise it could not perform the record and playback.

4. Host system supports format of the hard disk. If the hard disk has been used, please note

whether it is FAT32 format. The embedded network digital video recorder supports only FAT32
format, otherwise there will be a hidden danger.
Note: Please format hard disk when it is the first time for you to use.

``

Table of Contents

1. Hard Disk Installation ............................................................................................................................ 1

2. Rear Panel Interface ............................................................................................................................... 1

3. Host Side Operation ............................................................................................................................... 3

3.1 Start the System ........................................................................................................................ 3

3.2 System Login ............................................................................................................................ 3

4. System Toolbar ....................................................................................................................................... 6

4.1 Display Setting ......................................................................................................................... 6

4.2 PTZ Setting ............................................................................................................................... 8

4.3 Setting ....................................................................................................................................... 9

4.4 Playback ................................................................................................................................. 26

4.5 Backup .................................................................................................................................... 26

4.6 Record .................................................................................................................................... 27

4.7 Alarm ...................................................................................................................................... 27

4.8 Capture ................................................................................................................................... 27

4.9 File Manager ........................................................................................................................... 28

4.10 IP Channel Setting .................................................................................................................. 29

5. Preview................................................................................................................................................. 31

5.1 Drag and Drop the Image ....................................................................................................... 31

5.2 Drag to Change Channel Sequence ........................................................................................ 31

6. IE Viewing ........................................................................................................................................... 32

6.1 User Log In ............................................................................................................................. 32

7. Mobile View Operation Instruction ...................................................................................................... 32

7.1 Client Software Obtaining ...................................................................................................... 32

7.2 Parameters of the NVR which Supports Mobile Surveillance................................................ 32

7.3 Android ................................................................................................................................... 32

7.4 Blackberry .............................................................................................................................. 33

7.5 Windows Mobile System ........................................................................................................ 33

7.6 APPLE iOS ............................................................................................................................. 33

1. Hard Disk Installation

Prepare a screwdriver. Take 1U chassis as an example, this series NVR could be installed a hard
disk in the chassis, the largest capacity supports to 4TB.

Hard Disk Installation Steps：

1. Remove four screws on the side of 2. Connect the hard disk data and power
chassis and remove the top cover supply cable

3. Fix the HDD on the bottom plate 4. Put the cover back and fix it with screws

2. Rear Panel Interface

(Note: PoL ports only exist in specific models.)

POWER

HD

Audio

PoL

RS485
(PTZ)/Alarm

DC15V

LAN

USB

VGA

Video
OUT

Audio
OUT

For 4CH/8CH NVR model, the USB ports in front and bottom of the two ports in back(as the
structural diagram show above) share the same channel. If you plug two USB devices into
these two ports at the same time, they would not function normally.

3. Host Side Operation

3.1 Start the System

Plug power cable into the adapter and switch the power on, the power LED will light in red and the

NVR will start. After booting, the video output default to multi-window output mode.

The host side main screen. If you are not login, the system toolbar would show in gray and
the toolbar icons are not selectable.

If the booting time is within the record setting time period, the system will automatically enable the

record function.

Note:

Please use the power supply matching with the NVR instead of any other type or brand.

3.2 System Login

Click “Start” icon，there are five options:

1) User Guide: Setting up the guide language.

You can select the language of the User Guide.

Select the video format and resolution.

Setting up the network.

2) Power Off: Click this button to shutdown the device. You can also press the switch off at the

rear panel to shutdown the device. But we suggest to shutdown the device from the “Power
Off” button to avoid damaging the device from power failure by accident.

Note:

Before changing the HDD operation, please shutdown the device and disconnect the power
supply .

3) Reboot: Click this button to reboot the device.

4) Login: Click this button to login.

User name: admin
Password: blank

Click “Login”, you can find the system toolbar show in color and could be selectable.

5) onLock: Click this button to lock the menu.

4. System Toolbar

4.1 Display Setting

Click “Display Setting”icon to bring the menu below.

1) Language: Select the language you need. Then restart the device

2) AutoLogout: System automatically logout and lock time.

3) TV Adjust: Adjust the display position.

4) Display: Set monitor Brightness, Contrast, Saturation, Hue and Transparency.

5) Resolution: The default resolution is 1024x768, please select the best resolution according

the monitor condition. There are 6 options for selection.

6) Rotation interval: Setup the time interval of rotation. Tick “Enable SEQ” to start rotation.

Display Setting menu

Setting the Display Position

Setting Brightness, Contrast, Saturation, Hue and Transparency.

Note:

You can also right-click in the main screen to access the system toolbar.
Please note the menu order is different from the toolbar in the main screen.

4.2 PTZ Setting

Click “PTZ” icon to open the menu below.

You can Zoom in/out, change Iris and Focus.

Setting the cruise time and speed.

Tips: Digital Zooming

During image preview and playback, roll mouse

roller to do digital zooming, it zoom the image as

mouse pointer as the center. The max can do 15X

zooming. Drag the zoomed image by mouse to see

image detail.

Zoom In

Zoom Out

The channel is recording. Light flashing means frame lost or recording lost.

Magnifying glass: Digital zooming, the red number in the middle is magnification figures, click

this icon, it can change to PTZ control

4.3 Setting

Click “Setting” icon to enter the setting menu. There are six main setting options: Device, Channel,
Network, Alarm, Account, and System.

1. Device Setting

There are four sub options for “Device” Setting: Device Info, System Version, PTZ Setting, and
DST Setting.

Device Info

You can check the device information here.