SHANTOU IAEB19 User Manual
ADDITIONAL WARNINGS
•
this unit to rain or moisture.
• WARNING : Where the mains plug or appliance coupler is
used as the disconnect device, such disconnect device shall
remain readily operable.
• Lithium batteries, like all rechargeable batteries, are
recyclable and should be recycled or disposed of according to
state and local guidelines. They should never be disposed of in
normal household waste and they should never be incinerated,
as they might explode. Contact your local government for
disposal or recycling practices in your area.
• This product meets and complies with all Federal regulations.
• To avoid hearing damage, make sure that the volume on
your music player is turned down before connecting your
earbuds. After placing earbuds in/on your ears, gradually turn
up the volume until you reach a comfortable listening level.
WARNING : This product can exp ose you to
chemicals including lead, which i s known to the S tate
of California to cause cance r and birth d efects or other
reproductive harm . For more infor mation go to www.
P65Warnings.ca.gov.
Made
Green
Protect for Today
Sustain for Tomorrow
Wireless Stereo Headset
User’s Guide for Model IAEB19-2370-01
Features
• Bluetooth Wireless 5.0: range 49 feet
• Voice prompts announce earbud operations
• Built-in microphone
• Neck band controls
• Micro-USB port for battery recharge
• Built-in rechargeable battery
• Battery life: approx. 4 hrs at 100% volume
Includes
• 3 pairs of eartips - small / medium / large
• Micro-USB to USB charging cable
• User’s guide
Overview & Controls
LED Indicato r Light
& Microphone
Press and h old to
power ON/OFF.
Press to play/p ause audio
or answer/end a pho ne call.
Press to ch ange the
volume level.
Press and h old to change
the audio t rack.
Micro-USB Charging Port
Charging the Battery
Initial charge time is approximately 2 hours. Charge
fully before use.
• Pull back the cover on the Micro-USB charging
port and connect it to the USB port of a powered
on computer or USB power adaptor (not included)
to charge.
Power Status Indicator Light
Power ON Flashing Blue light
Low Battery Flashing Red light
Charging Solid Red light
Finished Charging Solid Blue light
Bluetooth Connection
1. This unit features automatic device pairing and
is ready to pair as soon as it powers on. Power on
the headset by pressing and holding the Power
button, then a voice will announce, “Power ON.”
The headset is ready to pair.
2. To connect to the headset, open the Bluetooth
Settings menu on your smartphone or tablet and
select IAEB19 from the list. If need be, refer to the
user’s manual for your device for more specic
instructions on Bluetooth pairing.
3. When successfully connected, a voice will
announce, “Bluetooth connected.” Use your
smartphone or tablet to select and play media.
Use the controls on your device or the headset to
play, pause, or skip audio, and adjust the volume.
4. After initial pairing, the headset will automatically
connect to the last device used whenever
powered on. To pair to another device, begin with
the unit powered OFF, then press and hold the
Power/Pair button on the headset and connect
to it using the new device.
Playing Audio Wirelessly
1. After connecting to Bluetooth, use the controls
on the connected device to select and play audio.
2. Use the controls on the unit or the connected
Bluetooth device to play, pause, or skip audio,
and adjust the volume level.
Using the Speakerphone
1. To accept a call, press the Speakerphone button
or use the controls on the connected phone.
2. To end a call, press the Speakerphone button or
use the controls on the connected phone.
Troubleshooting
If the earbuds should become unpaired or will not
connect normally, open your device’s Bluetooth
Settings Menu and follow these steps.
• Disconnect, then reconnect to the earbuds.
• If the problem persists, delete the earbuds from
the list of available devices (“Forget This Device”).
• Turn Bluetooth OFF then ON again, and repeat the
Bluetooth Connection steps.
Loading...