Page 1
®
ELECTRONICS AND FIBERGLASS DIVISION
18" Portable Satellite Antenna
Style DS-3005
ANTENNA/MOUNT MADE IN U.S.A.
UNPACKING
After unpacking the system, verify that you have 25 feet
of coax. If you do not, please contact Shakespeare at
(803) 276-5504. SAVE THE CARTON. This carton is
designed to be reused to protect your system when
not in use.
ELECTRONICS AND FIBERGLASS DIVISION
Shakespeare Electronic Products Group
6111 Shakespeare Rd., Columbia, SC 29223
®
Page 2
OPERATION
STEP 1. Connect coax from LNBF to receiver.
STEP 2. Plug in the receiver and TV.
NOTE: If you have the unit sitting on a tailgate or on
other metal items, it is recommended that you
remove the compass from the base and stand away
(15' min.) to find the correct azimuth. Compass is
attached to base with velcro.
STEP 3. Turn TV and receiver ON.
STEP 4. Tune TV to ch. 3 or 4.
STEP 5. Determine azimuth and elevation required for
your position. Refer to Quick Reference Card or receiver
manual.
STEP 6. Loosen clamp knobs. Elevate reflector to the
correct elevation. Align degree of elevation required with
front of the slide bracket. Each mark indicates 5 degrees
of elevation with the first mark being 00 (mark closest to
compass/level). See Figure 1. Tighten clamp knobs.
STEP 7. Level base using bubble level recessed into the
base.
STEP 8. Using compass recessed into base, rotate the
base
slowly
to the desired azimuth (direction) for the high
power satellites.
NOTE: Disregard the compass markings, the red
compass needle
always points North
. Rotate the
base so that the other end of the needle points at the
correct heading (direction) on the compass decal.
DO NOT USE THE DEGREE MARKINGS ON THE
COMPASS.
STEP 9. Adjust azimuth (direction) and elevation (up/
down) for best picture.
NOTE: If you do not get a picture, check the
following:
1. Make sure antenna has clear view of the high
power satellites, no buildings, trees, etc.
blocking the view.
2. Make sure coax connections are good.
3. Check coax for breaks, crimps, cuts etc.
4. If base is not level, you will have to adjust the
elevation to compensate.
5. Check that TV is tuned to correct channel.
CAUTION:
DO NOT DROP SYSTEM. IF ANTENNA IS
DAMAGED, IT WILL REDUCE THE GAIN (HOW MUCH
SIGNAL THE ANTENNA SENDS TO THE RECEIVER)
OF THE ANTENNA. THIS CAN RESULT IN A
DEGRADED PICTURE.
Reflector
0 Degrees Elevation
(Next Mark Indicates 50)
Clamp Knobs
Use Front of Slide Bracket
for Proper Degree of
Elevation Required.
Point Towards Satellite
FIGURE 1
Page 3
RETURNING ANTENNA TO TRAVEL POSITION
STEP 1. Turn receiver and TV OFF.
STEP 2. Disconnect coax from receiver.
STEP 3. Loosen clamp knobs and put antenna in travel
position. See Figure 2.
STEP 5. Coil coax under base. See Figure 3.
NOTE: The carton the system came in is designed to
FIGURE 2
be reused. It is suggested that you store your system
in it when not in use.
NOTE: When ready to use antenna again, you must
uncoil the coax before raising antenna. The antenna
will not raise if the coax is coiled up under the base.
RECEIVER WARRANTY
Receiver is warranted by the manufacturer. See instruction
manual packed with receiver for warranty information.
FIGURE 3
WINEGARD MOBILE PRODUCTS LIMITED WARRANTY
Winegard Company warrants this product against defects in materials or workmanship for a period of two (2) years from the date of original purchase. During
year one (1) of such warranty, Winegard Company will also pay authorized labor costs to an authorized Winegard dealer to repair or replace defective products.
No warranty claim will be honored unless at the time the claim is made, Customer presents proof of purchase to an authorized Winegard dealer (to locate the
nearest authorized Winegard dealer, contact Winegard Company, 3000 Kirkwood Street, Burlington, Iowa 52601, Telephone 800-288-8094 or visit
www.winegard.com). Customer must provide proof of purchase with a dated sales receipt for the Winegard product to verify the product is under warranty.
If the date of purchase cannot be verified, the warranty period shall be considered to begin thirty (30) days after the date of manufacture.
If a defect in material or workmanship is discovered, Customer may take the product to an authorized Winegard dealer for service. Customer must provide
proof of purchase to verify the product is under warranty. If the product is brought to an authorized Winegard dealer for service prior to expiration of year one
(1) of the warranty period and a defect in material or workmanship is verified by Winegard Technical Services, Winegard Company will cover the Winegard
dealer’s labor charges for warranty service. The Winegard dealer must contact Winegard Technical Services in advance for pre-approval of the service. Approval
of the service is at the sole discretion of Winegard Company.
Alternatively, Customer may ship the product prepaid to Winegard Technical Services (located at 3111 Kirkwood Street, Burlington, Iowa 52601, Telephone
800-788-4417). Customer must return the product along with a brief description of the problem and provide Winegard Technical Services with Customer’s name,
address, and phone number. Customer must also provide proof of purchase to verify the product is under warranty. If the product is returned before the expiration
of the warranty period, Winegard Company will (at its option) either repair or replace the product.
This Limited Warranty does not apply if the product has been damaged, deteriorates, malfunctions or fails from: improper installation, misuse, abuse, neglect,
accident, tampering, modification of the product as originally manufactured by Winegard in any manner whatsoever, removing or defacing any serial number,
usage not in accordance with product instructions or acts of nature such as damage caused by wind, lightning, ice or corrosive environments such as salt
spray and acid rain. This Limited Warranty also does not apply if the product becomes unable to perform its’ intended function in any way as a result of the
television signal provider making any changes in technology or service.
(2 YEARS PARTS; 1 YEAR LABOR)
Coil Coax
Around
Clips
A Return Material Authorization (RMA) is required prior to returning any product to Winegard Company or Winegard Warranty Services under this
warranty policy. Please call our Technical Services Department at 800-788-4417 or send an e-mail to
number. Please furnish the date of purchase when requesting an RMA number. Enclose the product in a prepaid package and write the RMA number in
large, clear letters on the outside of the package. To avoid confusion or misunderstanding, a shipment(s) without an RMA number(s) or an unauthorized
return(s) will be refused and returned to Customer freight collect.
WINEGARD COMPANY DOES NOT ASSUME ANY LIABILITIES FOR ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, MADE BY ANY OTHER
PERSON.
ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE
AND MERCHANTABILITY ARE LIMITED TO THE TWO YEAR PERIOD OF THIS WARRANTY.
In states that do not allow limitations on implied warranties, or the exclusion of limitation of incidental or consequential damages, the above limitations or exclusions
do not apply.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion of limitation of incidental or consequential damages, so the above
limitations or exclusions may not apply to you.
This warranty gives Customer specific legal rights. Customer may also have other rights that may vary from state to state
RETURN AUTHORIZATION POLICY
SATELLITE RECEIVER WARRANTY
See manufacturer’s limited warranty policy.
warranty@winegard.com to obtain the RMA
WS-MOBWARREV2
Rev. 1/10
Page 4
ANTENNA EXPLODED PARTS VIEW
Below is the exploded parts view for the 18"/26" portable
satellite system. If you require a replacement part, call
Shakespeare at (803) 276-5504.
2745309
46 cm Reflector
(4) 2160361
5/16-18 x 5/8" Flat Head Bolt
2753065
25' Coax
(4) 2160230
5/16-18 Hex Nut
2200921
Reflector Bracket
(5) 2160027
5/16" Washer
(2) 2745048
Pivot Link
(4) 2160690
0.312 x 0.660
Round Head Pin
2160821
Spring (not shown)
Cable Tie
2190104
2744846
FEED SUPPORT
ARM
(2) 2240021
Rubber Bumper
(2) 2200096
Clamp Knob
2160353
1/4-20 X 1.25 LONG
CARRIAGE BOLT
2780190
LNBF
2160220
1/4-20
HEX NYLOCK NUT
2200816
Base
2160691
0.312 x 2.91
Round Head Pin
(6) 2160696
E-Clip Retainer
2451154
2780258
Level
2780257
Compass
2160692
0.312 x 3.36
3201818
Slide W/Inserts
© 1999, 2005, 2006 Shakespeare Company Rev.2 1/10
Round Head Pin
Printed in U.S.A.
Loading...