Manufacture:Shadow Creator Information Technology Co., Ltd.
Shadow VR All Powerful
Shadow VR is about to bring you the ultimate
experience of immersion and interactivity.Please
read the instructions carefully and set up your device.
Here’s a rundown of Shadow VR’s
Accessories.
You can get more accessories at www.shadowcreator.com.
2
1
2
3
4
SHADOW VR
使用说明书
5
1. SHADOW VR
2. TYPE-C CABLE
3. POWER SUPPLY
4. MICROFIBER CLOTH
5. USER GUIDE
3
Basic Instructions
Function Keys
Power On、Wearing、Connect with Controller
4
Audio Jack
Type-C Interface
6DoF Camera
5
Volume
Head Strap
Power Button
Indicator Light/MIC
6
1.Turn Action One on
Press the power button and hold for 5 seconds to
turn on your Shadow VR when it's off.
7
2.Wearing
Please wear the headset following the
instruction above.
8
3.Connect with Controller
Press Power Button. The status indicator of
controller will be flashing (blue) if it is ready
(Bluetooth controllers are required to buy separately.)
to be connected with the headset.
9
6DoF Orientation
Indicator Light
Touchpad+Button
ReturnButton
Power Button
10
Programmable Buttons
Volume/
Cell Cover
Trigger
11
Controller
Bluetooth controllers are required to buy separately.
For a better experience, please buy two controllers.
Please visit www.shadowcreator.com for more information.
12
Hardware Revision:
Software Revision:
Frequency Band(s):
Transmit Power Range(s):
Modulation Type(s):
Channel Spacing(s):
Antenna type(s) and Gain(s):
V01-MB-V1.0
SW_V01_YC_A_V1.7.1_180813
Bluetooth 5.0+EDR:
Frequency Bands:2402-2480 MHz
Bluetooth 5.0 LE:
Frequency Bands:2402-2480 MHz
2.4GWIFI
802.11b/g/n(20MHz): 2412~2472MHz
5GWIFI
802.11a/n/ac (20MHz): 5745~5825MHz
802.11n /ac(40MHz):5755~5795MHz
802.11ac (80MHz):5775MHz
Bluetooth 5.0+EDR:
Max power:3.06dBm
Bluetooth 5.0 LE:
Max power:-2.96dBm
2.4GWIFI
Max power:15.62dBm
5GWIFI
Max power:11.38dBm
Bluetooth 5.0+EDR:
Modulation Mode: GFSK, π /4-DQPSK,8DPSK
Bluetooth 5.0 LE:
Modulation Mode: GFSK
This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device
does not cause harmful interference..
Any Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information:
This Virtual Reality HDM meets the government's requirements for exposure to radio waves. The
guidelines are based on standards that were developed by independent scientific organizations through
periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin
designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement
The SAR limit of USA (FCC) is 1.6 W/kg (head) averaged over one gram of tissue and 4.0 W/kg
(Extremity) averaged over ten gram of tissue.. Device types:Virtual Reality HDM
(FCC ID:2AQYUSHADOWV01) has also been tested against this SAR limit. The highest SAR value
reported under this standard during product certification for use at the head is 0.396W/kg
and at the Extremity is 0.132W/kg,This device was tested for head operations with the edge
of the helmet kept 0mm from the head and extremity. To maintain compliance with FCC RF exposure
requirements, use accessories thatmaintain a 0mm separation distance between the head and the
edge of the helmet.
CE Maintenance
1. Use careful with the earphone maybe excessive sound pressure from earphones
and headphones can cause hearing loss.
2.Risk of explosion if battery is replaced by an incorrect type. Dispose of used
batteries according to the instructions.
3.The product shall only be connected to a USB interface of version USB2.0.
4.Adapter shall be installed near the equipment and shall be easily accessible.
5.EUT Operating temperature range: -10° C to 40° C .
6.Adapter:
The plug considered as disconnect device of adapter
Input: AC 100-240V, 50/ 60Hz, 450mA
Output: 5.2V 2A
7.The device complies with RF specifications when the device used at 0 mm from
your body.
8.To prevent possible hearing damage. Do not listen at high volume levels for long
periods.
Declaration of Conformity
Shadow Creator Information Technology Co., Ltd. hereby declares that this Virtual
Reality HDM is in compliance with the essential requirements and other relevant
provisions of Directive 2014/53/EU.In accordance with Article 10(2) and Article
10(10),This product is allowed to be used in all EU member states.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.