W A R R A N T Y :
Upon receipt of your Polaris, please check to ensure you have received all of the parts.
NOTE: Wind damage is not covered under any manufacturer’s warranty.
5 Year Limited Warranty includes the LIBRA, ASTRAL-TC, SIRIUS, POLARIS,
ORION and GALAXY styles. This includes the mast, boom, head fitting, elbow, center
pole/sidepost, arms, ribs, top and bottom hub, and stainless steel hardware only. If
there is damage under the warranty, Shademaker will replace and/or repair any item
listed in this category at its discretion. Labor charges are not covered under this limited
warranty.
10 Year Limited Warranty includes the Sunbrella® awning & marine grade
Fabric Collection. Visit www.sunbrella.com/warranty for more details. Labor charges
are not covered under this limited warranty.
5 Year Limited Warranty applies to Sunbrella Firesist®, Sunbrella Firesist®
PLUS and Sunbrella® furniture grade, and O’bravia® awning grade fabrics.
Labor charges are not covered under this limited warranty.
1 Year Limited Warranty covers base wheels and the powder coat finish on all
bases. If the powder coat finish flakes, bubbles, peels or loses color; Shademaker will
re-finish or replace the defective bases at its discretion. Normal wear and tear is not
covered under this limited warranty. Labor charges are not covered under this limited
warranty.
Caution: Seaside and indoor pool use, salt & chlorides can accumulate on the powder
coat finish, leading to finish failure. Failure or neglect to make needed cleanings may
cause paint to blister, and such failure will void limited warranty.
Exclusions: Wind damage, acts of nature (such as, but not limited to, freezing or any
type of extreme weather). Failures caused by abusive use and normal wear and tear are
not covered under this warranty. Any Galaxy style that does not have spacer buttons
installed.
Parts can be ordered under warranty at no charge, if found that the damage is a
manufacture defect and/or purchased out of warranty to make them whole again.
IMPORTANT RESTRICTION FOR SM PRODUCTS WARRANTY SERVICE:
Shademaker restricts warranty service for SM products to the country where
Shademaker or its authorized SM retail Dealers originally sold the product.
Those filing warranty claims will be responsible for all shipping, handling and freight
charges on all claims to Shademaker in Baldwin Park, CA. All warranty claims must be
submitted with the original proof of purchase, date of purchase, name of dealer and the
description of the damage. An authorized Shademaker RA# must be listed on all
products being returned. The Shademaker warranty is not transferable. Shademaker
reserves the right to repair, replace and/or redesign any product that is returned under a
warranty claim.
For current warranty information, please visit www.shademakerusa.com.
T O P R O P E R L Y F O L D C A N O P Y
The 100% solution dyed canopy will last longer if you fold it as it was packed and
shipped. This technique is similar to the way a parachute is folded and is especially
important when folding the canopy for seasonal storage or when left in the closed
position for an extended period of time.
Using this technique at all times will significantly extend the life of
the canopy.
1. When the canopy has been fully lowered, stand in front of the
canopy structure and begin the folding process by pulling out
two panels opposite the mast.
Pull the two panels together and roll tight into the canopy.
2. Once rolled tight, pull adjacent panels out one at a time and
fold to the center, alternating sides until all the panels have
been pulled out from the arms and folded into the center.
3. Wrap provided strap around canopy to secure.
P R O T E C T I V E C O V E R
1. Screw rods together and insert into slit of the cover.
2. Unzip cover.
3. Using the rod as a guide, slide cover over your umbrella.
4. Pull on string to zip down your cover and tie.
M A I N T A I N I N G F R A M E & F I T T I N G S
1. Hose frame with water periodically, more often if installation is in a salty or industrial
environment.
2. Inspect the installation fitting, mount bolts, rib spacers, etc. on a regular basis and
tighten if necessary.
M A I N T A I N I N G C A N O P Y F A B R I C
1. Clean up spills and stains right away. Spills can be removed by using a clean
absorbent cloth.
2. For general maintenance, use a soft brush to remove dust and dry soil. Wash
down with clean, warm water (i.e., garden hose) every so often to avoid dirt
becoming ingrained. Allow the fabric to air dry before closing the canopy.
3. If a thorough cleaning is necessary, sponge over the fabric using a mild soap
solution (2% solution). Rinse well with plenty of water to remove all soap residue.
4. Never use detergents, cleaning fluids or solvents. Grease and oil stains may be
removed by using turpentine or similar with an absorbent cloth.
5. Please visit the fabric websites for more details: www.shademakerusa.com or
www.sunbrella.com
6. Use protective canopy cover during storage or when not in use.
R E M O V A L & R E P L A C E M E N T O F C A N O P Y
Follow these instructions should you choose to replace your canopy with a new canopy.
1. Lower the canopy to the closed position.
2. Remove the button/screw at the end of each arm.
3. Separate the Velcro strap along the main canopy arm and remove the canopy from
the structure.
4. To replace the canopy, reverse the above process.
Mast Rib
.06” .118”
4.65”
3.05”
2
I M P O R T A N T :
Please read this entire manual before installing or operating your Polaris umbrella.
P O L A R I S W I N D R E S I S T A N C E G U I D E L I N E S :
Light to Moderate Winds (if used with mount kits)
When installed properly, the Polaris is engineered to handle light to moderate wind
conditions in the open canopy position. Please adhere to these wind guidelines:
1. If winds are present, the Polaris should be closed.
2. Do not keep the Polaris in a tilt position if you are experiencing windy
conditions.
3. As winds get stronger or, in anticipation or uncertain/severe weather conditions,
the canopy should be lowered to the folded position and strapped to the mast.
4. The Polaris should always be left in the folded and strapped position when
unattended or not in use.
5. In anticipation of, and during extremely severe weather conditions, it is
advisable to remove and store the entire Polaris structure to protect it from
storm-related debris.
B
A
E
C
D
Weight: Approx. 121-142 lbs.
Mast Shape & Diameter: 4.65” x 3.05” Oval
Mast Thickness: 0.118”
Rib Thickness: 0.06”
S P E C I F I C A T I O N S
Item No.
A
Mast End to
Canopy Edge
B
Height to
Mast Top
C
Arm End
Height
(Open)
D
Arm End
Height
(Closed)
E
Height to
Canopy Top
(Open)
POLARIS-30S 11’ 9’2” 7’ 2’4” 8’8”
POLARIS-35S 12’9” 9’5” 7’3” 1’4” 9’3”
POLARIS-40S 14’3” 9’6” 7’3” 1’1” 9’8”
3
D
I A G R A M & P A R T S L I S T
11
567
123
3
4
8
91210
14
13
15
1. Internal Stem 6. Slider Car Stop Pin 11. Arm
2. Internal Stem Cover (optional) 7. Crank 12. Canopy
3. Bore Holes 8. Slider Car 13. Lower Hub
4. Turning Handle 9. Main Support Arm 14. Light Adapter
5. Mast 10. Upper Hub 15. Strut
To Close Canopy
1. Turn slider car pin counter clockwise to disengage. Move
slider car pin downward to a comfortable position. Turn
clockwise to lock into place. Turn crank handle counter-
clockwise until canopy is fully closed.
2. Turn slider car pin counter clockwise to disengage. Continue
guiding slider car downward until car fully reaches closed
position.
3. Turn slider car pin clockwise (to vertical position) to lock into
place.
4. Strap canopy to the mast with supplied strap.
To Rotate 360°
1. There are (8) 45° locking rotating positions. Raise the
turning handle above 90° and rotate mast to one of the 8
preset positions.
2. Lower handle to lock into place.
4
I N S T A L L A T I O N O P T I O N S A N D G U I D E L I N E S
There are four standard installation options which provide the best stability for the Polaris.
Depending on your situation, you will have requested one or more of the Polaris base
options at the time of your order.
1. CONCRETE MOUNT KIT - This kit includes a base plate, four (4) plate bolts, and
one (1) allen wrench.
2. IN-GROUND MOUNT KIT - This kit includes in-ground fitting, four (4) plate bolts,
and one (1) allen wrench.
3. STEEL BASE WEIGHT - 213 lbs. Square steel base weight is available (SM PLATE
required). We recommend a minimum of 600-800 lbs. of steel base weights for this
umbrella (depending on the size of your umbrella).
4. FREE STANDING STEEL FRAME - You may opt to use a free standing base for
your Polaris umbrella. We recommend a minimum of a 450-750lbs. base weight for
this umbrella (depending on the size of your umbrella). NOTE: If using a free-standing
steel frame, wind guidelines change from light to moderate winds to light winds only.
NOTE: REFER TO BASE WEIGHT MATRIX AND SEPARATE
MANUAL FOR BASE ASSEMBLY PRIOR TO PROCEEDING.
(Astral-TC Internal Stem shown)
Installing Internal Stem
Option A: If you wish to use optional internal stem cover, proceed below.
Otherwise, if you wish to not use cover and for a quicker installation, skip to
Option B on page 6.
Remove internal stem from bottom of mast by removing the three bolts underneath the
turning handle. NOTE: Do not remove the bolt above the turning handle!
Install internal stem onto mount kit, SM PLATE or steel base frame with supplied 5 bolts
and washers using allen wrench. Do not completely tighten. NOTE: Do not use power
drill. May cause damage to umbrella.
A S S E M B L Y I N S T R U C T I O N S
Two-person team is recommended for assembly.
By now, you have installed your mount kit, SM PLATE onto your steel base weight, or
have set up your steel base frame with recommended base weight.
5
(Astral-TC Internal Stem shown)
Option B: If you wish not to use optional internal stem cover, proceed below.
Using a two person team, lift umbrella with attached internal stem and install umbrella
onto mount kit, SM PLATE on your steel base weight. Tighten 5 bolts to secure
umbrella in place with allen wrench. Note: Do not use power drill. May cause damage
to umbrella. Once complete, proceed below.
Slide internal stem cover over bottom of Polaris mast. Using a two person team, lift
umbrella with cover and insert bottom of mast onto internal stem. Tighten 5 bolts to
secure umbrella in place. Slide internal stem cover down to cover internal stem.
Internal Mast Stem Cover Installed
Attaching Polaris to Internal Stem
Lift rotating handle from mast. Rotate Polaris mast until the bore holes for the locking
screws in the internal stem line up in the mast. Tighten locking screws with allen wrench
into the mast and internal stem to secure. Note: Do not use power drill. May cause
damage to umbrella. Once complete, proceed to “Leveling Umbrella” on page 6.
Bore Holes
Leveling Umbrella
Check the vertical position of the umbrella with a level tool.
If the umbrella is not level, lift optional internal stem cover to access internal stem.
Untighten the 5 bolts with 1-2 rotations (do not
stem can rotate without applying force. Correct the vertical level position with leveling
screws.
Once leveled, re-tighten the 5 bolts with allen wrench on internal stem. Note: Do not
use power drill. May cause damage to umbrella. Slide optional internal stem cover
down and cover internal stem.
6
Option B: If you wish not to use optional internal stem cover, proceed below.
Using a two person team, lift umbrella with attached internal stem and install umbrella
onto mount kit, SM PLATE on your steel base weight. Tighten 5 bolts to secure
umbrella in place with allen wrench. Note: Do not use power drill. May cause damage
to umbrella. Once complete, proceed below.
(Astral-TC Internal Stem shown)
You are now ready to operate your umbrella!
Leveling Umbrella
Check the vertical position of the umbrella with a level tool.
If the umbrella is not level, lift optional internal stem cover to access internal stem.
Untighten the 5 bolts with 1-2 rotations (do not
completely untighten bolts!). The internal
stem can rotate without applying force. Correct the vertical level position with leveling
screws.
Once leveled, re-tighten the 5 bolts with allen wrench on internal stem. Note: Do not
use power drill. May cause damage to umbrella. Slide optional internal stem cover
down and cover internal stem.
7
I N S T A L L A T I O N O P T I O N S A N D G U I D E L I N E S
There are four standard installation options which provide the best stability for the Polaris.
Depending on your situation, you will have requested one or more of the Polaris base
options at the time of your order.
1. CONCRETE MOUNT KIT - This kit includes a base plate, four (4) plate bolts, and
one (1) allen wrench.
2. IN-GROUND MOUNT KIT - This kit includes in-ground fitting, four (4) plate bolts,
and one (1) allen wrench.
3. STEEL BASE WEIGHT - 213 lbs. Square steel base weight is available (SM PLATE
required). We recommend a minimum of 600-800 lbs. of steel base weights for this
umbrella (depending on the size of your umbrella).
4. FREE STANDING STEEL FRAME - You may opt to use a free standing base for
your Polaris umbrella. We recommend a minimum of a 450-750lbs. base weight for
this umbrella (depending on the size of your umbrella). NOTE: If using a free-standing
steel frame, wind guidelines change from light to moderate winds to light winds only.
Installing Internal Stem
Option A: If you wish to use optional internal stem cover, proceed below.
Otherwise, if you wish to not use cover and for a quicker installation, skip to
Option B on page 6.
Remove internal stem from bottom of mast by removing the three bolts underneath the
turning handle. NOTE: Do not remove the bolt above the turning handle!
Install internal stem onto mount kit, SM PLATE or steel base frame with supplied 5 bolts
and washers using allen wrench. Do not completely tighten. NOTE: Do not use power
drill. May cause damage to umbrella.
A S S E M B L Y I N S T R U C T I O N S
Two-person team is recommended for assembly.
By now, you have installed your mount kit, SM PLATE onto your steel base weight, or
have set up your steel base frame with recommended base weight.
O P E R A T I N G I N S T R U C T I O N S
R
emove all packaging from umbrella.
To Open Canopy
1. Remove the strap that holds the Polaris to the mast when in the closed position.
Take note of the “parachute” folding method used to fold the canopy when closed.
See TO PROPERLY FOLD CANOPY section on page 10 for more details.
2. Untie fabric from small hinges and remove. NOTE: Hinge fabrics purpose are to
protect hinges from scratching canopy during transportation.
3. Slightly loosen arms. CAUTION: NEVER FORCE THE ARMS. If you experience any
resistance, make sure all arms are freed manually to facilitate opening.
4. Crank handle clockwise (refer to arrows on crank housing). Continue cranking to open
completely.
To Tilt Canopy
The Polaris has infinite tilt positions.
1. Stand under umbrella. Turn slider car stop pin
counter-clockwise to a horizontal position. Slider
car is now ready for tilt position. Guide slider car
stop pin to tilt to desired location.
2. To lock into place, turn the slider car stop pin
clockwise to a vertical position. Slider car is now
locked in the teeth belt.
3. Repeat steps above to lower or raise canopy to
desired tilt position.
8
To Close Canopy
1. Turn slider car pin counter clockwise to disengage. Move
slider car pin downward to a comfortable position. Turn
clockwise to lock into place. Turn crank handle counterclockwise until canopy is fully closed.
2. Turn slider car pin counter clockwise to disengage. Continue
guiding slider car downward until car fully reaches closed
position.
3. Turn slider car pin clockwise (to vertical position) to lock into
place.
4. Strap canopy to the mast with supplied strap.
To Rotate 360°
1. There are (8) 45° locking rotating positions. Raise the
turning handle above 90° and rotate mast to one of the 8
preset positions.
2. Lower handle to lock into place.
Mast Rib
.06” .118”
4.65”
3.05”
9
I M P O R T A N T :
Please read this entire manual before installing or operating your Polaris umbrella.
P O L A R I S W I N D R E S I S T A N C E G U I D E L I N E S :
When installed properly, the Polaris is engineered to handle light to moderate wind
conditions in the open canopy position. Please adhere to these wind guidelines:
1. If winds are present, the Polaris should be closed.
2. Do not keep the Polaris in a tilt position if you are experiencing windy
conditions.
3. As winds get stronger or, in anticipation or uncertain/severe weather conditions,
the canopy should be lowered to the folded position and strapped to the mast.
4. The Polaris should always be left in the folded and strapped position when
unattended or not in use.
5. In anticipation of, and during extremely severe weather conditions, it is
advisable to remove and store the entire Polaris structure to protect it from
storm-related debris.
B
A
E
C
D
Weight: Approx. 121-142 lbs.
Mast Shape & Diameter: 4.65” x 3.05” Oval
Mast Thickness: 0.118”
Rib Thickness: 0.06”
S P E C I F I C A T I O N S
Item No.
POLARIS-30S 11’ 9’2” 7’ 2’4” 8’8”
POLARIS-35S 12’9” 9’5” 7’3” 1’4” 9’3”
POLARIS-40S 14’3” 9’6” 7’3” 1’1” 9’8”
L I G H T A D A P T E R
To open light adapter:
Loosen light adapter built into the umbrella runner by turning
counter-clockwise. After loosening, pull down light adapter
post and attach umbrella light (sold separately).
To close light adapter:
Gently push up the light adapter post back into umbrella
runner and tighten turning clockwise NOTE: It is not
necessary to remove light to close umbrella.
10
T O P R O P E R L Y F O L D C A N O P Y
The 100% solution dyed canopy will last longer if you fold it as it was packed and
shipped. This technique is similar to the way a parachute is folded and is especially
important when folding the canopy for seasonal storage or when left in the closed
position for an extended period of time.
Using this technique at all times will significantly extend the life of
the canopy.
1. When the canopy has been fully lowered, stand in front of the
canopy structure and begin the folding process by pulling out
two panels opposite the mast.
Pull the two panels together and roll tight into the canopy.
2. Once rolled tight, pull adjacent panels out one at a time and
fold to the center, alternating sides until all the panels have
been pulled out from the arms and folded into the center.
3. Wrap provided strap around canopy to secure.
P R O T E C T I V E C O V E R
1. Screw rods together and insert into slit of the cover.
2. Unzip cover.
3. Using the rod as a guide, slide cover over your umbrella.
4. Pull on string to zip down your cover and tie.
M A I N T A I N I N G F R A M E & F I T T I N G S
1. Hose frame with water periodically, more often if installation is in a salty or industrial
environment.
2. Inspect the installation fitting, mount bolts, rib spacers, etc. on a regular basis and
tighten if necessary.
M A I N T A I N I N G C A N O P Y F A B R I C
1. Clean up spills and stains right away. Spills can be removed by using a clean
absorbent cloth.
2. For general maintenance, use a soft brush to remove dust and dry soil. Wash
down with clean, warm water (i.e., garden hose) every so often to avoid dirt
becoming ingrained. Allow the fabric to air dry before closing the canopy.
3. If a thorough cleaning is necessary, sponge over the fabric using a mild soap
solution (2% solution). Rinse well with plenty of water to remove all soap residue.
4. Never use detergents, cleaning fluids or solvents. Grease and oil stains may be
removed by using turpentine or similar with an absorbent cloth.
5. Please visit the fabric websites for more details: www.shademakerusa.com or
www.sunbrella.com
6. Use protective canopy cover during storage or when not in use.
R E M O V A L & R E P L A C E M E N T O F C A N O P Y
Follow these instructions should you choose to replace your canopy with a new canopy.
1. Lower the canopy to the closed position.
2. Remove the button/screw at the end of each arm.
3. Separate the Velcro strap along the main canopy arm and remove the canopy from
the structure.
4. To replace the canopy, reverse the above process.
13401 Brooks Drive
Baldwin Park, C A 91706
p 626.338.8810
f 62 6 . 3 3 8 . 8 8 1 6
info@shademakerusa.com
shademakerusa.com
©2018 Shademaker. All rights reserved. SMOM-POLARIS-0718
Loading...