User’s guide
SH49-SH50
WARNING:
• Read the instructions manual before assembling and/or using the case.
• Make sure the case and its accessories are properly assembled.
• Make sure that the case is properly closed and locked with key before starting the motorcycle.
• The maximum load of the motorcycle case is of 8 kg, provided that the carrier allows it.
• The maximum speed of the motorcycle with the case full must not exceed 120 km/h (this may vary
depending on the legislation of each country).
• The cases may significantly reduce the security, stability and performance of the motorcycle.
• When cleaning the case use water with neutral soap, always avoid using solvents or chemical
products.
• For a long lasting use of the case, SHAD recommends the use of its spare parts.
• When using the top case SH49-SH50, SHAD recommends using side cases, SH36 SH43 or SH42.
• Keep this guide as a reference for further doubts regarding the use or assembling of the case.
ASSEMBLY PRECAUTIONS
• SHAD will not hold responsibility for damages caused by an incorrect assembly or
adjustment carried out by unqualified personnel.
• If problems or questions should rise during the assembling of the case, contact
the dealership, distributor or manufacturer directly.
2
OPEN THE CASE
(OPEN):
Turn the key 90º clockwise from the
position CLOSE towards the position
OPEN. In this position, push the
button, the handle will tilt forward
automatically.
Use the lever to open the case.
SH49-SH50
90º
OPEN
OPEN
4
The handle should be in the upright
position in order to close the Top
Case.
PLACING THE CASE ON
THE RACK (RELEASE):
Turn the key 135º clockwise from the
position CLOSE towards the position
SH49-SH50
135º
RELEASE
RELEASE OPEN
5
RELEASE. Push the button, the
handle will tilt forward automatically.
Pull the lower lever to release the
case from the bottom rack.
SH49-SH50
RELEASE
6
INSTALLING THE
COLOR PLATE SH50:
Using a Ø3 mm drill bit, drill 4
holes on the inner side of the
case. Next, fasten the color plate
using the screws.
Ø
3 mm
TAPA EMBELLECEDORA SH50
7
INSTALLING THE
BACKREST SH50:
Position the backrest over the
top case as illustrated and
fasten with 3 screws on the
inner side of the case.
SH50
Accessories On Top case SH49 it’s possible to put the backrest DORI60.
8
LIGHT KIT
Verify that breaklight does not interfere with the light system of the motocycle.
The Light Kit has to be assembled according to the current European directive.
KIT LUZ SH49-SH50
C
C
BRAKE
GROUND
TAIL
A
BRAKE
GROUND
4
4
TAIL
55
5
Number Reference Quantity
1 200890 (KIT LIGHT) 1
2 304127 (Screw M3’5x13 DIN7982) 1
3 200851 (Plastic bridles) 3
1
1
2
2
4 304017 (Screw M5x16 DIN7985) 2
5 305058 (Rapid Nut TRT-M5-1) 2
B
9
11
8
1
10
999
8118
10
1
SH49-SH50
SHAD
Fitting kit
2
5
4
3
1
9
8
4
3
9
8
5
2
4
1
SHAD
Fitting kit
Consult accessories with your
Note:
distributor.
It can only be used on the Top or Full
(*)
master.
(**) Included in the specific support.
66
10
9
9
Number Reference Quantity
1 201834 (Support piece) 1
8
8
7
7
4
4
1
1
6
6
5
5
6
6
2
2
2 201049 (Bridle) 4
3 304144 (Screw M6x40 DIN 965) 4
4 200713/2 (Plastic bridle) 4
5
303000 (Ø6 Washer fs M6 DIN 125 A)
6 302021 (M6 Nut M6 DIN 985) 4
7 304058 (Screw M6x30 DIN 965) 4
8 201835 (Cover support piece) 1
9 304127 (Screw Ø3’5x13 DIN 7982) 4
10 201504 (Metal piece) * 4
11 304074 (Screw M8x20 DIN 912) ** 4
12
303020 (Ø8 Washer fs M8 DIN 125 A) **
13 302024 (Nut M8 DIN 985) ** 4
4
SH49-SH50
4
99
8
8
11
11
10
10
1
1
12
12
13
13
11
Find out more about luggage systems & saddlebags we have.
Loading...