SGS Thomson Microelectronics 74VCXHR162245TTR Datasheet
1/11July 2003
■ 3.6V TOLERANT INPUTS A N D OUTPUTS
■ HIGH SPEED IN BOTH A, B OUTPUTS:
t
PD
= 3.4 ns (MAX.) at VCC=3.0to3.6V
t
PD
= 4.3 ns (MAX.) at VCC=2.3to2.7V
■ SYMMETRICAL IMPEDANCE OUTPUTS:
|I
OH
|=IOL= 12mA (MIN) at VCC=3.0V
|I
OH
|=IOL=8mA(MIN)atVCC=2.3V
■ POWER DOWN PROTECTION ON INPUTS
AND OUTPUTS
■ 26ΩSERIE RESISTORS IN BOTH A AND B
PORT OUTPUTS
■ OPERATING VOLTAGE RANGE :
V
CC
(OPR) = 2.3V to 3.6V
■ PIN AND FUNCTION COMPATIBLE WITH
74 SERIES HR162245
■ BUSHOLDPROVIDEDONBOTHSIDES
■ LAT CH-UP PERFORMANCE EXCEEDS
300mA (JESD 17)
■ ESD PERFORMANCE:
HBM > 2 000V (MIL STD 883 method 3015);
MM > 200V
DESCRIPTION
The 74VCXHR162245 is a low v oltage CMO S 16
BIT BUS TRANSCEIVER (3-STATE) fabricated
with sub-micron silicon gate and five-layer metal
wiring C
2
MOS technology. It is ideal for low power
and very high speed 2.3 to 3.6V applicat ions; it
can be interfa ce d to 3.6V signal environment for
both inputs and outputs.
This IC is intended for two -wa y asynch ronous
communication between data buses; the direction
of data transmission is determined by DIR input.
The t wo enable inputs nG
canbeusedtodisable
the device so that the buses are effectively
isolated. The device circuits is including 26Ω
series resistance in the A a nd B port outputs.
These resistors permit to reduce line noise in high
speed application s. Bus hold on data inputs is
provided in order to eliminate the need for external
pull-up or pull-down res ist or.
All inputs and outputs are equipped with
protection circuits against st atic discharge, giving
them 2KV ESD imm unit y and transient excess
voltage. All floating bus terminals during High Z
State must be held HIGH or LOW.
74VCXHR162245
LOW VOLTAGE CMOS 16-BIT BUS TRANSCEIVER
(3-STATE) WITH 3.6V TOLERANT INPUTS AND OUTPUTS
ORDER CODES
PACKAGE TUBE T & R
TSSOP 74VCXHR162245TTR
TSSOP
PIN CONNECTION
74VCXHR162245
2/11
INPUT AND OUTPUT EQUIVALENT CIRCUIT
PIN DESCRIPTION
TRUTH TABLE
X : Don‘tCare
Z : High Impedance
IEC LOGIC SYMBOLS
PIN No SYMBOL NAME AND FUNCTION
1 1DIR Directional Control
2, 3, 5, 6, 8, 9,
11, 12
1B1 to 1B8 Data Inputs/Outputs
13,14,16,17,
19, 20, 22, 23
2B1 to 2B8 Data Inputs/Outputs
24 2DIR Directional Control
25 2G
Output Enable Input
36,35,33,32,
30, 29, 27, 26
2A1 to 2A8 Data Inputs/Outputs
47,46,44,43,
41, 40, 38, 38
1A1 to 1A8 Data Inputs/Outputs
48 1G
Output Enable Input
4, 10, 15, 21,
28, 34, 39, 45
GND Ground (0V)
7, 18, 31, 42
V
CC
Positive Supply Voltage
INPUTS FUNCTION OUTPUT
G
DIR A BUS B BUS Yn
L L OUTPUT INPUT A = B
L H INPUT OUTPUT B = A
HXZZZ
74VCXHR162245
3/11
ABSOLUTE MAXIMUM RATINGS
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
1) I
O
absolute maximum rating must be observed
2) V
O
<GND,VO>V
CC
RECOMMENDED OPERATING CONDITIONS
1) VINfrom0.8V to 2V at VCC=3.0V
Symbol Parameter Value Unit
V
CC
Supply Voltage
-0.5 to +4.6 V
V
I
DC Input Voltage
-0.5 to +4.6 V
V
O
DC Output Voltage (OFF State)
-0.5 to +4.6 V
V
O
DC Output Voltage (High or Low State) (note 1) -0.5 to VCC+ 0.5
V
I
IK
DC Input Diode Current
-50 mA
I
OK
DC Output Diode Current (note 2)
-50 mA
I
O
DC Output Current
± 50 mA
I
CC
or I
GND
DC VCCor Ground Current per Supply Pin
± 100 mA
P
D
Power Dissipation
400 mW
T
stg
Storage Temperature
-65 to +150 °C
T
L
Lead Temperature (10 sec)
300 °C
Symbol Parameter Value Unit
V
CC
Supply Voltage
2.3 to 3.6 V
V
I
Input Voltage
-0.3 to 3.6 V
V
O
Output Voltage (OFF State)
0 to 3.6 V
V
O
Output Voltage (High or Low State) 0 to V
CC
V
I
OH,IOL
High or Low Level Output Current (VCC= 3.0 to 3.6V)
± 12 mA
I
OH,IOL
High or Low Level Output Current (VCC= 2.3 to 2.7V)
± 8mA
T
op
Operating Temperature
-55 to 125 °C
dt/dv Input Rise and Fall Time (note 1) 0 to 10 ns/V
74VCXHR162245
4/11
DC SPECIFICATIONS (2.7V < VCC< 3.6V unless oth erwise s pecified)
Symbol Parameter
Test Condition Value
Unit
V
CC
(V)
-40to85°C -55to125°C
Min. Max. Min. Max.
V
IH
High Level Input
Voltage
2.7to3.6
2.0 2.0
V
V
IL
Low Level Input
Voltage
0.8 0.8
V
OH
High Level Output
Voltage
2.7to3.6
IO=-100 µAVCC-0.2 VCC-0.2
V
2.7
I
O
=-6 mA
2.2 2.2
3.0
I
O
=-8 mA
2.4 2.4
I
O
=-12 mA
2.2 2.2
V
OL
Low Level Output
Voltage
2.7to3.6
IO=100 µA
0.2 0.2
V
2.7
I
O
=6 mA
0.4 0.4
3.0
I
O
=8 mA
0.55 0.55
I
O
=12 mA
0.8 0.8
I
I
Input Leakage
Current
2.7to3.6
V
I
= 0 to 3.6V
± 5 ± 5 µA
I
I(HOLD)
Input Hold Current
3.0
VI= 0.8V
75 75
µA
V
I
=2V
-75 -75
3.6
V
I
= 0 to 3.6V
± 500 ± 500
I
off
Power Off Leakage
Current
0
V
I
or VO= 0 to 3.6V
10 10 µA
I
OZ
High Impedance
Output Leakage
Current
2.7to3.6
V
I=VIH
or V
IL
VO= 0 to 3.6V
± 10 ± 10 µA
I
CC
Quiescent Supply
Current
2.7to3.6
V
I=VCC
or GND
20 20
µA
V
I
or VO=VCCto
3.6V
± 20 ± 20
∆I
CC
ICCincr. per Input
2.7to3.6
VIH=VCC-0.6V
750 750 µA
Loading...