SGS Thomson Microelectronics 74VCXH162244TTR Datasheet
1/11February 2003
■ 3.6V TOLERANT INPUTS AND OUTPUTS
■ HIGH SPEED :
t
PD
= 3.4 ns (MAX.) at VCC=3.0to3.6V
t
PD
= 3.8 ns (MAX.) at VCC=2.3to2.7V
■ POWER DOWN PROTECTION ON INPUTS
AND OUTPUTS
■ SYMMETRICAL OUTPUT IMPEDANCE:
|I
OH
|=IOL= 12mA (MIN) at VCC=3.0V
|I
OH
|=IOL=8mA(MIN)atVCC=2.3V
■ 26Ω SERIE RESISTORS IN OUTPUTS
■ OPERATING VOLTAGE RANGE:
V
CC
(OPR) = 2.3V to 3.6V
■ PIN AND FUNCTION COMPATIBLE WITH
74 SERIES H162244
■ BUS HOLD PROVIDED ON DATA INPUTS
■ LATCH-UP P ERFO RMANCE EXCEEDS
300mA (JESD 17)
■ ESD PERFORMANCE:
HBM > 2000V (MIL STD 883 method 3015);
MM > 200V
DESCRIPTION
The 74VCXH162244 is a low voltage CMOS 16
BIT BUS BUFFER (NON INVERTED) fabricated
with sub-micron silicon gate and five-layer metal
wiring C
2
MOS technology. It is ideal for low power
and very high speed 2. 3 to 3.6V application s; it
can be interfaced to 3.6V signal environmen t for
both inputs and outputs.
Any nG
output con trol governs four BUS
BUFFERS. Output Enable input (nG
) tied together
gives full 16-bit operation.
When nG
is LO W, the outputs are on. When nG is
HIGH, the output are in high impedance state.
This dev ice is designed to be used with 3 state
memory addre ss drivers, etc. Bus hold on data
inputs is p ro vided in order to eli minate the need for
external pull-up or pull-down resistor.
The device circuits is including 26Ω series
resistance in the outputs. These resistors permit
to reduce line noise in high speed applications.
All inputs and outputs are equipped with
protection circuits against static discharge, giving
them 2KV ESD immunity and transient exc es s
voltage.
74VCXH162244
LOW VOLTAGE CMOS 16-BIT BUS BUFFER (3-STATE INV.)
WITH 3.6V TOLERANT INPUTS AND OUTPUTS
ORDER CODES
PACKAGE TUBE T & R
TSSOP 74VCXH162244TTR
TSSOP
PIN CO NNE CTION
74VCXH162244
2/11
INPUT AND OUTPUT EQUIVALENT CIRCUIT
PIN DESCRIPTION
TRUTH TABLE
X : Don‘t Care
Z : High Impedance
IEC LOGIC SYMBOLS
PIN No SYMBOL NAME AND FUNCTION
11G
Output Enable Input
2, 3, 5, 6 1Y1 to 1Y4 Data Outputs
8, 9, 11, 12 2Y1 to 2Y4 Data Outputs
13, 14, 16, 17 3Y1 to 3Y4 Data Outputs
19, 20, 22, 23 4Y1 to 4Y4 Data Outputs
24 4G
Output Enable Input
25 3G
Output Enable Input
30, 29, 27, 26 4A1 to 4A4 Data Outputs
36, 35, 33, 32 3A1 to 3A4 Data Outputs
41, 40, 38, 37 2A1 to 2A4 Data Outputs
47, 46, 44, 43 1A1 to 1A4 Data Outputs
48 2G
Output Enable Input
4, 10, 15, 21,
28, 34, 39, 45
GND Ground (0V)
7, 18, 31, 42
V
CC
Positive Supply Voltage
INPUTS OUTPUT
G
An Yn
LLL
LHH
HXZ
74VCXH162244
3/11
ABSOLUTE MAXIMUM RATINGS
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
1) I
O
absolute maximum rating must be observed
2) V
O
<GND,VO>V
CC
RECOMMENDED OPERATING CONDITIONS
1) VINfrom0.8V to 2Vat VCC=3.0V
Symbol Parameter Value Unit
V
CC
Supply Voltage
-0.5 to +4.6 V
V
I
DC Input Voltage
-0.5 to +4.6 V
V
O
DC Output Voltage (OFF State)
-0.5 to +4.6 V
V
O
DC Output Voltage (High or Low State) (note 1) -0.5 to VCC+ 0.5
V
I
IK
DC Input Diode Current
-50 mA
I
OK
DC Output Diode Current (note 2)
-50 mA
I
O
DC Output Current
± 50 mA
I
CC
or I
GND
DC VCCor Ground Current per Supply Pin
± 100 mA
P
D
Power Dissipation
400 mW
T
stg
Storage Temperature
-65 to +150 °C
T
L
Lead Temperature (10 sec)
300 °C
Symbol Parameter Value Unit
V
CC
Supply Voltage
2.3 to 3.6 V
V
I
Input Voltage
-0.3 to 3.6 V
V
O
Output Voltage (OFF State)
0 to 3.6 V
V
O
Output Voltage (High or Low State) 0 to V
CC
V
I
OH,IOL
High or Low Level Output Current (VCC= 3.0 to 3.6V)
± 12 mA
I
OH,IOL
High or Low Level Output Current (VCC= 2.3 to 2.7V)
± 8mA
T
op
Operating Temperature
-55 to 125 °C
dt/dv Input Rise and Fall Time (note 1) 0 to 10 ns/V
74VCXH162244
4/11
DC SPECIFICATIONS (2.7V < VCC< 3.6V unless otherwise specified)
Symbol Parameter
Test Condition Value
Unit
V
CC
(V)
-40to85°C -55to125°C
Min. Max. Min. Max.
V
IH
High Level Input
Voltage
2.7to3.6
2.0 2.0
V
V
IL
Low Level Input
Voltage
0.8 0.8
V
OH
High Level Output
Voltage
2.7to3.6
IO=-100 µAVCC-0.2 VCC-0.2
V
2.7
I
O
=-6 mA
2.2 2.2
3.0
I
O
=-8 mA
2.4 2.4
I
O
=-12 mA
2.2 2.2
V
OL
Low Level Output
Voltage
2.7to3.6
IO=100 µA
0.2 0.2
V
2.7
I
O
=6 mA
0.4 0.4
3.0
I
O
=8 mA
0.5 0.5
I
O
=12 mA
0.8 0.8
I
I
Input Leakage
Current
2.7to3.6
V
I=VCC
or GND
± 5 ± 5 µA
I
I(HOLD)
Input Hold Current
3.0
VI= 0.8V
75 75
µA
V
I
=2V
-75 -75
3.6
V
I
= 0 to 3.6V
± 500 ± 500
I
off
Power Off Leakage
Current
0
V
I
or VO= 0 to 3.6V
10 10 µA
I
OZ
High Impedance
Output Leakage
Current
2.7to3.6
V
I=VIH
or V
IL
VO= 0 to 3.6V
± 10 ± 10 µA
I
CC
Quiescent Supply
Current
2.7to3.6
V
I=VCC
or GND
20 20
µA
V
I
or VO=VCCto
3.6V
± 20 ± 20
∆I
CC
ICCincr. per Input
2.7to3.6
VIH=VCC-0.6V
750 750 µA
Loading...