SGS Thomson Microelectronics 74VCX162374TTR Datasheet

1/12February 2003

■ 3.6V TOLERANT INPUTS AND OUTPUTS

■ HIGH SPEED :

t

PD

= 3.4 ns (MAX.) at VCC=3.0to3.6V

t

PD

= 4.8 ns (MAX.) at VCC=2.3to2.7V

t

PD

= 6.0 ns (MAX.) at VCC=1.8V

■ POWER DOWN PROTECTION ON INPUTS

AND OUTPUTS

■ SYMMETRICAL OUTPUT IMPEDANCE:

|I

OH

|=IOL= 12mA (MIN) at VCC=3.0V

|I

OH

|=IOL=8mA(MIN)atVCC=2.3V

|I

OH

|=IOL=4mA(MIN)atVCC=1.8V

■ 26Ω SERIE RESISTORS IN OUTPUTS

■ OPERATING VOLTAGE RANGE:

V

CC

(OPR) = 1.8V to 3.6V

■ PIN AND FUNCTION COMPATIBLE WITH

74 SERIES 162374

■ LATCH-UP PERFORMANCE EXCEEDS

300mA (JESD 17)

■ ESD PERFORMANCE:

HBM > 2000V (MIL STD 883 method 3015);
MM > 200V

DESCRIPTION

The 74VCX162374 is a low voltage CMOS 16 BIT
D-TYPE FLIP-FLOP with 3 STATE OUTPUTS
NON INVERTING fabricated with sub-micron
silicon gate and five-layer metal wiring C

2

MOS
technology. It is ideal for low power and very high
speed 1.8 to 3.6V applications; it can be interfac ed
to 3.6V signal environment for both inputs and
outputs.
These 16 bit D-TYPE flip-flops are controlled by
two clock inputs (nCK) and two output enable
inputs (nOE

).
Onthepositivetransitionofthe(nCK),thenQ
outputs wi ll be s et to the logic state that were
setup at the nD inputs.
While the (nOE

) input is low, the 8 outputs (nQ)
will be in a normal state (HIGH or LOW logic lev el)
and while high level the outputs w ill be in a high
impedance state.
Any output control does not aff ec t the internal
operation of flip flops; that is, the old data can be
retained or the new data can be entered even
while the outputs are off.

74VCX162374

LOW VOLTAGE CMOS 16-BIT D-TYPE FLIP-FLOP (3-STATE)

WITH 3.6V TOLERANT INPUTS AND OUTP UT S

ORDER CODES

PACKAGE TUBE T & R

TSSOP 74VCX162374TTR

TSSOP

PIN CO NNE CTION

74VCX162374

2/12

The device circuits is including 26Ω series
resistance in the outputs. These resistors permit
to reduce line noise in high speed applications.

All inputs and outputs are equipped with
protection circuits against static discharge, giving
them 2KV ESD immunity and transient excess
voltage.

INPUT AND OUTPUT EQUIVALENT CIRCUIT

PIN DESCRIPTION

TRUTH TABLE

X : Don‘t Care
Z : High Impedance

IEC LOGIC SYMBOLS

PIN No SYMBOL NAME AND FUNCTION

1 1OE

3 State Output Enable
Input (Active LOW)

2, 3,5,6,8,9,

11, 12

1Q0 to 1Q7 3-State Outputs

13,14,16,17,

19, 20, 22, 23

2Q0 to 2Q7 3-State Outputs

24 2OE

3 State Output Enable
Input (Active LOW)

25 2CK Clock Input

36,35,33,32,

30, 29, 27, 26

2D0 to 2D7 Data Inputs

47,46,44,43,

41, 40, 38, 37

1D0 to 1D7 Data Inputs

48 1CK Clock Input

4, 10, 15, 21,
28, 34, 39, 45

GND Ground (0V)

7, 18, 31, 42 V

CC

Positive Supply Voltage

INPUTS OUTPUT

OE

CK D Q

HXX Z

L X NO CHANGE*
LLL
LHH

74VCX162374

3/12

LOGIC DIAGRAM

This logic diagram has not to be used to estimate propagation delays

ABSOLUTE MAXIMUM RATINGS

Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied

1) I

O

absolute maximum rating must be observed

2) VO<GND,VO>V

CC

RECOMMENDED OPERATING CONDITIONS

1) VINfrom0.8V to 2Vat VCC=3.0V

Symbol Parameter Value Unit

V

CC

Supply Voltage

-0.5 to +4.6 V

V

I

DC Input Voltage

-0.5 to +4.6 V

V

O

DC Output Voltage (OFF State)

-0.5 to +4.6 V

V

O

DC Output Voltage (High or Low State) (note 1) -0.5 to VCC+ 0.5

V

I

IK

DC Input Diode Current

-50 mA

I

OK

DC Output Diode Current (note 2)

-50 mA

I

O

DC Output Current

± 50 mA

I

CC

or I

GND

DC VCCor Ground Current per Supply Pin

± 100 mA

P

D

Power Dissipation

400 mW

T

stg

Storage Temperature

-65 to +150 °C

T

L

Lead Temperature (10 sec)

300 °C

Symbol Parameter Value Unit

V

CC

Supply Voltage

1.8 to 3.6 V

V

I

Input Voltage

-0.3 to 3.6 V

V

O

Output Voltage (OFF State)

0 to 3.6 V

V

O

Output Voltage (High or Low State) 0 to V

CC

V

I

OH,IOL

High or Low Level Output Current (VCC= 3.0 to 3.6V)

± 12 mA

I

OH,IOL

High or Low Level Output Current (VCC= 2.3 to 2.7V)

± 8mA

I

OH,IOL

High or Low Level Output Current (VCC= 1.8V)

± 4mA

T

op

Operating Temperature

-55 to 125 °C

dt/dv Input Rise and Fall Time (note 1) 0 to 10 ns/V

74VCX162374

4/12

DC SPECIFICATIONS (2.7V < VCC< 3.6V unless otherwise specified)

Symbol Parameter

Test Condition Value

Unit

V

CC

(V)

-40to85°C -55to125°C

Min. Max. Min. Max.

V

IH

High Level Input
Voltage

2.7to3.6

2.0 2.0
V

V

IL

Low Level Input
Voltage

0.8 0.8

V

OH

High Level Output
Voltage

2.7to3.6

IO=-100 µAVCC-0.2 VCC-0.2

V

2.7

I

O

=-6 mA

2.2 2.2

3.0

I

O

=-8 mA

2.4 2.4

I

O

=-12 mA

2.2 2.2

V

OL

Low Level Output
Voltage

2.7to3.6

IO=100 µA

0.2 0.2
V

2.7

I

O

=6 mA

0.4 0.4

3.0

I

O

=8 mA

0.55 0.55

I

O

=12 mA

0.8 0.8

I

I

Input Leakage
Current

2.7to3.6

V

I

= 0 to 3.6V

± 5 ± 5 µA

I

off

Power Off Leakage
Current

0

V

I

or VO= 0 to 3.6V

10 10 µA

I

OZ

High Impedance
Output Leakage
Current

2.7to3.6

V

I=VIH

or V

IL

VO= 0 to 3.6V

± 10 ± 10 µA

I

CC

Quiescent Supply
Current

2.7to3.6

VI=VCCor GND

20 20

µA

V

I

or VO=VCCto

3.6V

± 20 ± 20

∆I

CC

ICCincr. per Input

2.7to3.6

VIH=VCC-0.6V

750 750 µA