Sfera Labs SPTM20XP, SPTB30XP, SPTB30X42, SPTB30X44, SPTU30XP User Manual

...

Pi Touch Display Kit User Guide

July 2020

Revision 012

SPTM20XP Strato Pi Mini Touch Display Kit with Raspberry Pi 3 Model B+

SPTB30XP Strato Pi Base Touch Display Kit with Raspberry Pi 3 Model B+

SPTB30X42 Strato Pi Base Touch Display Kit with Raspberry Pi 4 Model B 2GB

SPTB30X44 Strato Pi Base Touch Display Kit with Raspberry Pi 4 Model B 2GB

SPTU30XP Strato Pi UPS Touch Display Kit with Raspberry Pi 3 Model B+

SPTU30X42 Strato Pi UPS Touch Display Kit with Raspberry Pi 4 Model B 2GB

SPTU30X44 Strato Pi UPS Touch Display Kit with Raspberry Pi 4 Model B 2GB

SPTC12XP Strato Pi CAN Touch Display Kit with Raspberry Pi 3 Model B+

SPTC12X42 Strato Pi CAN Touch Display Kit with Raspberry Pi 4 Model B 2GB

SPTC12X44 Strato Pi CAN Touch Display Kit with Raspberry Pi 4 Model B 2GB

IPTB20RP Iono Pi Touch Display Kit with Raspberry Pi 3 Model B+

IPTB20R42 Iono Pi Touch Display Kit with Raspberry Pi 4 Model B 2GB

IPTB20R44 Iono Pi Touch Display Kit with Raspberry Pi 4 Model B 4GB

Safety information 3

Qualiﬁed personnel 3

Hazard levels 3

Safety instructions 4

General safety instructions 4

Battery and external rechargeable battery 4

Introduction 6

Kit Components 7

Features 8

Usage and connections 11

Hardware installation 11

microSD installation 11

Power supply 12

Wiring and GPIO operations 12

Replacing the RTC backup battery 12

Software installation 13

Technical speciﬁcations 14

Dimensions 15

Disposal 16

Installation and use restrictions 16

Standards and regulations 16

Safety instructions 16

Set-up 16

Conformity Information 17

User Guide

Be sure to always remove the power supply before handling the kit.

Don't touch any components on the Raspberry Pi card or other cards

while the device is on.

Follow all applicable electrical safety standards, guidelines,

speciﬁcations and regulations for installation, wiring and operations of

the Pi Touch Display Kit.

Carefully and fully read this user guide before installation.

The Pi Touch Display Kit is not authorised for use in safety-critical applications where a

failure of the product would reasonably be expected to cause personal injury or death.

Safety-critical applications include, without limitation, life support devices and systems,

equipment or systems for the operation of nuclear facilities and weapons systems. The kit

is neither designed nor intended for use in critical military or aerospace applications or

environments and for automotive applications or environment. Customer acknowledges

and agrees that any such use of the Pi Touch Display Kit is solely at Customer's risk, and

that Customer is solely responsible for compliance with all legal and regulatory

requirements in connection with such use.

Sfera Labs S.r.l. may make changes to speciﬁcations and product descriptions at any time,

without notice. The product information on the web site or materials is subject to change

without notice.

Please download and read the Terms and Conditions document available at:

http://www.sferalabs.cc

Strato, Iono and Sfera Labs are trademarks of Sfera Labs S.r.l. Other brands and names

may be claimed as the property of others.

User Guide

Safety information

Carefully and fully read this user guide before installation and retain it for future reference.

Qualiﬁed personnel

The product described in this manual must be operated only by personnel qualiﬁed for the speciﬁc task and installation environment, in accordance with all relevant documentation and safety instructions. A qualiﬁed person should be capable of fully identifying all installation and operation risks and avoid potential hazards when working with this product.

Hazard levels

This manual contains information you must observe to ensure your personal safety and prevent damage to property. Safety information in this manual are highlighted by the safety symbols below, graded according to the degree of danger.

Indicates a hazardous situation which, if not avoided, will result in death or serious personal injury.

Indicates a hazardous situation which, if not avoided, may result in death or serious personal injury.

Indicates a hazardous situation which, if not avoided, can result in minor or moderate personal injury.

Indicates a situation which, if not avoided, can result in damage of property.

DANGER

WARNING

CAUTION

NOTICE

User Guide

Safety instructions

General safety instructions

Protect the unit against moisture, dirt and any kind of damage during transport, storage and operation. Do not operate the unit outside the speciﬁed technical data.

Never open the housing. If not otherwise speciﬁed, install in closed housing (e.g. distribution cabinet). Earth the unit at the terminals provided, if existing, for this purpose. Do not obstruct cooling of the unit. Keep out of the reach of children.

Life threatening voltages are present within and around an open control cabinet.

When installing this product in a control cabinet or any other areas where dangerous voltages are present, always switch off the power supply to the cabinet or equipment.

Risk of ﬁre if not installed and operated properly.

Follow all applicable electrical safety standards, guidelines, speciﬁcations and regulations for installation, wiring and operations of this product.

The Raspberry Pi board could generate a substantial amount of heat when the software forces the CPU and/or GPU to operate at high load levels. Ensure that the product is properly installed and ventilated to prevent overheat.

The connection of expansion devices to this product may damage the product and other connected systems, and may violate safety rules and regulations regarding radio interference and electromagnetic compatibility.

Use only appropriate tools when installing this product. Using excessive force with tools may damage the product, alter its characteristics or degrade its safety.

Battery and external rechargeable battery

This product uses a small lithium non-rechargeable battery to power its internal real time clock (RTC). It also optionally uses an external rechargeable lead-acid battery for the uninterruptible power supply.

WARNING

NOTICE

User Guide

Improper handling of lithium and lead-acid batteries can result in an explosion of the batteries and/or release of harmful substances.

Worn-out or defective batteries can compromise the function of this product.

Replace the RTC lithium battery before it is completely discharged. The lithium battery must be replaced only with an identical battery. See the "Replacing the RTC backup battery" section for instructions.

Do not throw lithium batteries into ﬁre, do not solder on the cell body, do not recharge, do not open, do not short-circuit, do not reverse polarity, do not heat above 100°C and protect from direct sunlight, moisture and condensation.

Only use a lead-acid battery with electrical ratings recommended in the technical speciﬁcations for this product.

Follow the battery manufacturer's instructions when installing the external UPS battery (not provided).

Dispose of used batteries according to local regulations and the battery manufacturer's

instructions.

WARNING

User Guide

+ 13 hidden pages