Version 1.2 January 2013
Point-of-Sale
Hardware System
User Manual
i
Copyright 2013
All Rights Reserved
Manual Version 1.2
Part Number: 3LMPP3450412
The information contained in this document is subject to change without notice.
We make no warranty of any kind with regard to this material, including, but not
limited to, the implied warranties of merchantability and fitness for a particular
purpose. We shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of
this material.
This document contains proprietary information that is protected by copyright. All
rights are reserved. No part of this document may be photocopied, reproduced or
translated to another language without the prior written consent of the
manufacturer.
TRADEMARK
Intel®, Pentium® and MMX are registered trademarks of Intel® Corporation.
Microsoft® and Windows® are registered trademarks of Microsoft Corporation.
Other trademarks mentioned herein are the property of their respective owners.
ii
Safety
IMPORTANT SAFETY INSTRUCTIONS
1. To disconnect the machine from the electrical Power Supply, turn off the power
switch and remove the power cord plug from the wall socket. The wall socket
must be easily accessible and in close proximity to the machine.
2. Read these instructions carefully. Save these instructions for future reference.
3. Follow all warnings and instructions marked on the product.
4. Do not use this product near water.
5. Do not place this product on an unstable cart, stand, or table. The product may
fall, causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for
ventilation; to ensure reliable operation of the product and to protect it from
overheating. These openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed, sofa, rug, or other
similar surface. This product should never be placed near or over a radiator or
heat register, or in a built-in installation unless proper ventilation is provided.
7. This product should be operated from the type of power indicated on the marking
label. If you are not sure of the type of power available, consult your dealer or
local power company.
8. Do not allow anything to rest on the power cord. Do not locate this product where
persons will walk on the cord.
9. Never push objects of any kind into this product through cabinet slots as they
may touch dangerous voltage points or short out parts that could result in a fire
or electric shock. Never spill liquid of any kind on the product.
CE MARK
This device complies with the requirements of the EEC directive 2004/108/EC
with regard to “Electromagnetic compatibility” and 2006/95/EC “Low Voltage
Directive”
FCC
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation
iii
CAUTION ON LITHIUM BATTERIES
There is a danger of explosion if the battery is replaced incorrectly. Replace only with
the same or equivalent type recommended by the manufacturer. Discard used
batteries according to the manufacturer’s instructions.
Battery Caution
Risk of explosion if battery is replaced by an incorrectly type.
Dispose of used battery according to the local disposal instructions.
Safety Caution
Note: To comply with IEC60950-1 Clause 2.5 (limited power sources, L.P.S) related
legislation, peripherals shall be 4.7.3.2 "Materials for fire enclosure" compliant.
4.7.3.2 Materials for fire enclosures
For MOVABLE EQUIPMENT having a total mass not exceeding
18kg.the material of a FIRE ENCLOSURE, in the thinnest significant
wall thickness used, shall be of V-1 CLASS MATERIAL or shall pass
the test of Clause A.2.
For MOVABLE EQUIPMENT having a total mass exceeding 18kg
and for all STATIONARY EQUIPMENT, the material of a FIRE
ENCLOSURE, in the thinnest significant wall thickness used, shall
be of 5VB CLASS MATERIAL or shall pass the test of Clause A.1
LEGISLATION AND WEEE SYMBOL
2012/19/EU Waste Electrical and Electronic Equipment Directive on the treatment,
collection, recycling and disposal of electric and electronic devices and their
components.
The crossed dustbin symbol on the device means that it should not be disposed of
with other household wastes at the end of its working life. Instead, the device
iv
should be taken to the waste collection centers for activation of the treatment,
collection, recycling and disposal procedure.
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they can take
this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of
the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
v
Revision History
Revision Date Description
V1.0 October, 2009 Release
V1.1 May, 2011 C46 MB added
V1.2 January,2013
C56 MB added
C36 MB and C46 MB removed
VFD installation changed
2nd installation changed
vi
This page is intentionally left blank
i
Table of Contents
1 Package Checklist.........................................1
1-1 Standard items .................................................................. 1
1-2 Optional items ................................................................... 2
2 System View ...................................................3
2-1 Front View .......................................................................... 3
2-2 Side View & Bottom View.................................................. 4
2-3 I/O View.............................................................................. 5
3 System Assembly & Disassembly.................6
3-1 Replace the HDD ............................................................... 6
3-2 Replace the Motherboard................................................. 7
3-3 Stand Disassembly............................................................ 8
4 Peripheral Installation................................9
4-1 MSR installation ................................................................ 9
4-2 2-in-1 MSR + iButton Installation...................................10
4-3 2-in-1 MSR + Fingerprint Installation.............................11
4-4 Cash Drawer Installation.................................................12
4-5 VFD Installation ...............................................................14
4-6 2nd Display Installation.................................................... 16
5 Specification ............................................... 18
6 Jumper Settings .......................................... 20
6-1 C56 Motherboard Layout................................................20
6-2 Connectors & Functions.................................................. 21
6-3 Jumper Settings............................................................... 22
7 Appendix...................................................... 26
1
1 Package Checklist
1-1 Standard items
a. System b. Power adapter
c. Power cord d. RJ45 to DB9 cable (x2)
e. Driver CD
2
1-2 Optional items
a. MSR b. 2-in-1 MSR + iButton
c. 2-in-1 MSR + Fingerprint d. 2nd display module
e. VFD module
3
2 System View
2-1 Front View
No. Description
1 Touch screen
2 MSR/2-in-1 MSR (optional)
3 HDD door
4 Stand
5 Ventilation
6 Power button
4
1
5
3
2
6
4
2-2 Side View & Bottom View
No. Description
7 Hinge cover
8 System box (motherboard inside)
7
8
5
2-3 I/O View
No. Description
a Cash drawer port
b USB (x4)
c LAN (10/100/1000)
d COM1, 2, 3, 4 (from left to right)
e 2nd VGA
f DC In 19V
g Power button
h Parallel port
6
3 System Assembly & Disassembly
3-1 Replace the HDD
1. Remove the screw (x1) to remove the HDD cover.
2. Remove the screw (x1) that secures the HDD to the metal bracket.
3. Disconnect the HDD Cable and take out the HDD.
7
3-2 Replace the Motherboard
1. Turn off the powe r.
2. Remove the screws (x4) to open the system box.
3. Disconnect all the cables (x5) from the motherboard as the arrows show in the picture.
4. Remove the screws (x5) fixing the motherboard on the motherboard tray
5. Remove the hex screws (x4) to release the VGA and parallel port from the I/O metal
bracket.
8
3-3 Stand Disassembly
To remove the stand, you need to disconnect the LCD cable firstly.
1. Follow the steps 1 and 2 in Chapter to open the system box to access the motherboard.
2. Find the LCD cable and disconnect it from the motherboard.
3. Remove the hinge cover at both sides.
4. Remove the screws (x6) at both sides to release the LCD panel and the stand.
LCD Module
Stand
LCD Module
9
4 Peripheral Installation
4-1 MSR installation
1. Remove screws (x2) to open the MSR dummy cover.
2. Fasten the grounding cable (x1) and connect the MSR cable (x1).
3. Insert the MSR module in place.
4. Fasten the screws (x2) on the back to secure the MSR module.
10
4-2 2-in-1 MSR + iButton Installation
1. Remove screws (x2) to open the MSR dummy cover.
2. Connect the 2-in-1 MSR + iButton cable to the connector on system side.
3. Insert 2-in-1 MSR + iButton module in place and fasten the screws (x2) on the back to
secure the module.
11
4-3 2-in-1 MSR + Fingerprint Installation
1. Remove screws (x2) to open the MSR dummy cover.
2. Fasten the grounding cable (x1) and connect the 2-in-1 MSR + Fingerprint cable to the
connector on system side.
3. Insert 2-in-1 MSR + Fingerprint module in place and fasten the screws (x2) on the back
to secure the module.
12
4-4 Cash Drawer Installation
You can install a cash drawer through the cash drawer port. Please verify the pin
assignment before installation.
Cash Drawer Pin Assignment
Cash Drawer Controller Register
The Cash Drawer Controller use one I/O addresses to control the Cash Drawer.
Register Location: 48Ch
Attribute: Read / Write
Size: 8bit
BIT BIT7 BIT6 BIT5
BIT4 BIT3 BIT2 BIT1 BIT0
Attribute Reserved Read
Reserved Write Reserved
7 6 5 4 3 2 1 0
X X X X X
Reserved
Cash Drawer “DOUT bit0” pin output control
Cash Drawer “DOUT bit1” pin output control
Reserved
Cash Drawer “DIN bit0” pin input status
Reserved
Pin Signal
1 GND
2 DOUT bit0
3 DIN bit0
4 12V / 19V
5 DOUT bit1
6 GND
13
Bit 7: Reserved
Bit 6: Cash Drawer “DIN bit0” pin input status.
= 1: the Cash Drawer closed or no Cash Drawer
= 0: the Cash Drawer opened
Bit 5: Reserved
Bit 4: Reserved
Bit 3: Cash Drawer “DOUT bit1” pin output control.
= 1: Opening the Cash Drawer
= 0: Allow close the Cash Drawer
Bit 2: Cash Drawer “DOUT bit0” pin output control.
= 1: Opening the Cash Drawer
= 0: Allow close the Cash Drawer
Bit 1: Reserved
Bit 0: Reserved
Note: Please follow the Cash Drawer control signal design to control the Cash
Drawer.
Cash Drawer Control Command Example
Use Debug.EXE program under DOS or Windows98
Command Cash Drawer
O 48C 04 Opening
O 48C 00 Allow to close
Set the I/O address 48Ch bit2 =1 for opening Cash Drawer by “DOUT
bit0” pin control.
Set the I/O address 48Ch bit2 = 0 for allow close Cash Drawer.
Command Cash Drawer
I 48C Check status
The I/O address 48Ch bit6 =1 mean the Cash Drawer is opened or not
exist.
The I/O address 48Ch bit6 =0 mean the Cash Drawer is closed.
14
4-5 VFD Installation
1. The package includes a metal plate for assemble the VFD module. Please insert the
VFD to the metal plate and fasten screws (x4) on the bottom.
2. Follow steps 1~3 in Chapter 3-1 to take out the HDD.
3. Thread the VFD cable through the hole of the stand and route it as shown in the
picture.
15
4. Install the HDD to the position.
5. Connect the other end of the VFD cable to the USB port on the system.
16
4-6 2
nd
Display Installation
1. The package includes a metal plate for assemble the 2nd display module. Please
insert the 2nd display to the metal plate and fasten screws (x4) on the bottom.
2. Follow steps 1~3 in Chapter 3-1 to take out the HDD.
3. Thread the 2nd display cable through the hole of the stand and route it as shown in the
picture.
17
4. Install the HDD to the position.
5. Connect the other end of the 2nd display cable to the VGA port on the system.
8.4’ 2nd display
15.1’ 2nd display
18
5 Specification
Model Name
POS 345
Motherboard C56
CPU Support Intel Cedarview D2550 dual-core 1.86GHz, L2 1M
Chipset CPU integrated graphic + NM10
System Memory 1 x DDR3 SO-DIMM up to 4GB, 1066MHz
Graphic Memory Intel GMA 3650 (Gfx frequency up to 640MHz), DX9
LCD Touch Panel
LCD Size 15” TFT LCD
Brightness 250nits
Maximal Resolution 1024 x 768
Touch Screen Type Resistive
Tilt Angle 0° ~ 70°
Storage
HDD One 2.5" SATA HDD bay
Flash Memory SATA SSD flash card (optional)
Expansion
PCI-E Socket support 802.11 B/G/N WLAN card
Front I/O Ports
Power Button 1
Rear I/O Ports
USB 4 ports (V2.0)
Serial / COM
4 x RJ45 COM
(COM1 standard RS232; COM2 0V, COM3 5V, COM4 12V, power enabled by BIOS)
Parallel 1 (optional)
LAN (10/100/1000) 1
DC Jack
1 (19V-IN)
2nd VGA
1 (12V power enabled by BIOS)
Cash Drawer Port 1 x RJ 11 (12V / 19V)
Power
Power Adapter 65W /19V
Peripherals
MSR 3 Tracks MSR (USB)
19
Model Name
POS 345
2-in-1 MSR
MSR (USB) + iButton (USB)
MSR (USB) + Fingerprint (USB)
Customer Display 2 x 20 VFD customer display (COM)
Second Display 8.4" /15.1" LCD display
Environment
EMC & Safety FCC/CE Class A, LVD
Operating Temperature
0
o
C ~ 35 oC (32oF ~ 95 oF)
Storage Temperature -20 oC ~ 60 oC (-4 oF ~ 140 oF)
Humidity 20% ~ 80% RH non condensing
LCD 0 degree : 368 x 302 x 321 mm
Dimension
(W x D x H)
LCD70 degree : 368 x 290 x 221 mm
Weight (N.W./G.W.)
6.4kgs / 7.4kgs
OS Support
Windows XP, POS Ready 2009, XP Embedded, XP professional for Embedded, Linux, Windows 7
(32bit), POSReady
* This specification is subject to change without prior notice.
20
6 Jumper Setting
6-1 C56 Motherboard Layout
21
6-2 Connectors & Functions
Connector Function
CN1 LVDS Inverter Connector
CN2 System FAN Connector
CN3 LVDS Connector
CN4 Power LED Connector
CN5 SATA LED Connector
CN6 Speaker & MIC Connector
CN8 SATA Power Connector
CN9 COM5(Touch) Connector
CN10 Printer Port Connector
CN11/12 USB Port(Internal)
CN13 LAN LED Connector
CN14 PS2 Keyboard Connector
CN15 Card Reader Connector(COM6)
CN16 +19V DC IN Connector
CN17 Power button(Internal)
CN18 Front I/O Connector(USB/power LED/ Power button)
PWR2/3 +19V DC JACK
RJ11_1 Cash Drawer Connector
RJ45_1 LAN Connector
RJ45_2 COM1/ COM2/ COM3/ COM4
DDR3_A1 DDR3 SO-DIMM
SATA1/2/4 SATA Connector
SKT1 BIOS Connector
USB1 USB6 USB7
USB2 USB4 USB5
VGA1 VGA Connector
SW1 Power button
JP1 Inverter Select
JP2 CMOS Operation Mode
JP3 LCD ID Setting
JP4 H/W Reset
JP5 COM2 Power Setting
JP6 COM3/COM4 Power Setting
JP7 Auto Button Setting
JP8 Touch Connector
JP9 CASH DRAWER Power Setting
22
6-3 Jumper Setting
Cash Drawer Power Setting
Function JP9 (1-2) (3-4)
▲+19V
+12V
Inverter Selection
Function JP1 (1-2) (3-4) (5-6)
▲LED
CCFL
COM2 Power Setting
Function JP5 (1-2) (3-4)
▲ No Power
COM2 +5V
COM2 +12V
▲
= Manufacturer Default Setting OPEN SHORT
23
COM 3 & COM4 Power Setting
Function JP6 (1-2) (3-4) (5-6) (7-8)
▲COM3 +5V
COM3 +12V
COM4+ 5V
▲COM4 +12V
COM2/COM3/COM4 Power Setting
COM2, COM3 and COM4 can be set to provide power to your serial device.
The voltage can be set to +5V or +12V by setting jumper JP5 and JP6 on the
motherboard. When enabled, the power is available on pin 10 of the RJ45 serial
connector. If you use the serial RJ45 to DB9 adapter cable, the power is on pin 9 of
the DB9 connector. By default, the power option is disabled in the BIOS.
1. Power on the system, and press the
<DEL> key when the system is booting
up to enter the BIOS Setup utility.
2. Select the Advanced tab.
3. Select VGA/COM Power and LCD
Brightness Configuration Ports and
press <Enter> to go to display the
available options.
4. To enable the power, select COM2 ,
COM3 or COM4 Power setting and
press <Enter>. Select Power and
press <Enter>. Save the change by
pressing F10.
24
LCD ID Setting
LVDS Panel
Number
Resolution
Bits Channel
Output
Interface
JP3
(1-2) (3-4) (5-6) (7-8) (9-10)
1 800 x 600 18 Single
LVDS
Panel
2 800 x 600 18 Single
LVDS
Panel
3 800 x 600 24 Single
LVDS
Panel
4 1024 x 600 18 Single
LVDS
Panel
5 1024 x 768 18 Single
LVDS
Panel
6 800 x 600 24 Single
LVDS
Panel
7 1024 x 768 24 Single
LVDS
Panel
10 1366 x 768 18 Single
LVDS
Panel
11 1366 x 768 24 Single
LVDS
Panel
CRT
*Panel No.6 for 8.4” (HSD0841SN1-A01)HANNSTAR and 10.4” (A1048N03 V.1) AUO
25
2nd VGA Power Setting
1. Power on the system, and press the
<DEL> key when the system is booting
up to enter the BIOS Setup utility.
2. Select the Advanced tab.
3. Select VGA/COM Power and LCD
Brightness Configuration Ports and
press <Enter> to go to display the
available options.
4. To switch on the power, select "+12V"
press <Enter>. Please Save the
change by pressing F10.
26
7 Appendix
Drivers Installation:
The shipping package includes a Driver CD. You can find every individual driver and
utility that enables you to install the drivers in the Driver CD.
Please insert the Driver CD into the drive and double click on the “index.htm” to
pick up the models. You can refer to the drivers installation guide for each driver in
the “Driver/Manual List”.
Loading...