SEWOO LK-P20II User Manual
All specifications are subject to change without notice
P20Ⅱ Rev. D 11/16
J. STEPHEN Lab., Ltd.
374-2, Gajang-dong, Osan-si, Gyeonggi-do, 447-210, Korea
TEL : +82-31-459-8200 FAX : +82-31-459-8880
www.miniprinter.com
USER’S MANUAL
MODEL : LK-P20Ⅱ
1
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTION
Table of Contents
1.
Safety Caution
2
2.
Unpacking
4
3. Product Overview 5
4. Usage and Installation 6
4-1. Control panel usage 6
4-2. Battery installation 7
4-3. Charging battery 8
4-4. Battery charger usage
(Optional)
9
4-5. Usage of cigar jack for charging
(Optional)
10
4-6. Battery removal 11
4-7. Belt clip usage 12
4-8. Loading the media. 13
4-9. Shoulder strap usage (
Optional)
14
4-10. Leather case usage
(Optional)
15
4-11. Self test 16
4-12. MSR usage
(Optional)
18
4-13. IC CARD usage
(Optional)
19
5. Peripherals Connection 20
5-1. Bluetooth connection
(Optional)
20
5-2. Wi-Fi connection
(Optional)
20
5-3. Interface cable connection 21
6. Printer Cleaning 22
7. Standard Roll Media Specification 23
8. Black Mark 24
9. Printer Specification 25
10. Certification 27
11. Setting up the Software 29
2
3
For higher reliability and safety, consider the following precautionary measures.
Read and follow the instructions carefully before running of the product.
1. Safety Caution
WARNING
Failure to follow these instructions could result in re, electric shock,
or other injuries, or property damage
Indication
Prohibition
(Potential risk of electric shock or re)
(Potential risk of electric shock or re) (Potential risk of electric shock or re)
(Potential risk of electric shock or re)
Must follow
Do not disassemble
Unplug the power from the
outlet
Grounding to prevent electric
shock
Do not handle the product
with wet hands
Do not pull or touch the power plug with
wet hands.
Do not bend the wire and do not allow the
wire to be pressed by heavy object.
If a power plug is broken or a plug is cut or
worn, do not use it.
Do not overload the power plug into one
outlet.
WARNING
Failure to follow these instructions could result in re, electric shock,
or other injuries, or property damage
Failure to follow these instructions could result in re, electric shock,
or other injuries, or property damage
(Turn off the power at installation,
transportation, wiring and inspection.)
(You may get hurt and it can be broken
when it falls)
(Potential risk of re or unit malfunction)
(Potential risk of re or unit malfunction)
(Potential risk of discoloration or
electric shock)
(Potential risk unit malfunction, electric
shock or re. When the product needs
to be repaired, please contact in place
where you ordered.inspection.)
Dealer
Do not pull out the power plug to turn off
the product.
Do not install the product in uneven or
inclined surface.
If the product that needs to be repaired,
please contact in place where you ordered.
Please do not give excessive shock.
Keep product away from the water and
other material.
Do not disassemble, repair or modify the
product.
CAUTION
4
5
2. Unpacking
3. Product Overview
Power
switch
DC power
Belt clip hole
Battery
Paper feed
button
MSR slot
(Optional)
IC Card Slot
(Optional)
Open button
SERIAL
USB
Front
Rear
Printer
Battery
Battery Recharger
Belt Buckle Roll Paper
USB Cable Quick ManualCD
Printer Case Strap
Charger
Cigar Jack Charger Serial Cable
Optional
Standard
6
7
4-1 Control panel usage
Button Name
function
Power
button
This button is used to turn the printer on and off.
When the printer is off, press this button for approximately 3 seconds
and it will turn on the power. When you press this button in a state
that the printer is on, the printer will turn off.
Paper
feed
button
Paper output can be done manually by pressing this button.
Additionally, self-testing and Hexadecimal Dumping can be
processed..
1. Refer to “4-11” for self test information.
2. Refer to the service manual regarding Hexadecimal Dumping.
Battery
status
lamp
1. If the Batt, LED are Lit, the battery is fully charged.
2. If you can hear beeping sound and LED light is turned off, it means
that the battery is at the lowest level.
3. If the battery is not charged at all, the printer turns off
automatically.
Error
lamp
If the red light is turned on, it means there is no paper roll or the
paper cover is open.
4. Usage and Installation
4-2 Battery Installation
1. Align battery hook as shown in the picture
2. Push the battery into the printer until it locks in place.
NOTE
As the battery is not charged at the time of your purchase, charge the
battery prior to using the printer
(Battery charger or Cradle can be used to charge)
Hook
8
9
4-3 Charging battery
NOTE
1. Unless the exclusive charger is used provided by the manufacturer, the printer
can be damaged, and the manufacturer is not liable for the consequential damage.
2. Before removing the battery, make sure that power is turned off.
3. Printer does not work in the status of being connected with charger only.
4. The battery should be installed to operate printer.
5. While charging, do not turn on the power.
6. Do not operate the print while charging the battery.
7. Do not connect the charger while the printer is operated.
1. Be sure that the printer is turned off
2. After open the DC JACK cover, insert DC JACK into the printer.
3. Plug the power code to electrical outlet.
Lamp
4-3-1 The status of lamp in charging
Status charging charging complete
Charging Lamp
Red
Green
4-4-1 The status of lamp in charging
Status charging charging complete
Charging Lamp
Red
Green
NOTE
In the case the battery is not fixed properly in the holder, the red lamp will be
blinking, Then, extract and reinsert the battery.
1. Insert the battery into the battery holder as shown above
2. Connect the DC JACK to the power electrical outlet.
3. Once the charging is completed, remove the battery from the holder.
4-4 Battery charger usage
Optional
Lamp
Loading...