SEWON TELETECH STS1943HMDEFC, STS1943HMAAD, STS843HMD, STS1943HMABDE Users Manual

To: AirWalk communications, Co., Ltd.

User’s Manual

Model no. All Slim RU series

881, Gwanyang-2dong, Dongan-gu, Anyang-si,

Gyeonggi 431-804, Republic of Korea

Phone: [phone] Fax: [phone]

Reference

User Manual

Revision IR Page 1 / 25

Design Document for

Slim RU Version 1.2

Revision history

Rev. Date Chap. Changes Note

1.0 Apr.25, 2008 First draft

1. sector configuration added in 1

1.2 Jul.2, 2008 1

2. port setting added in 3.2.1

Design Document for

Slim RU Version 1.2

Reference

User Manual

Revision IR Page 2 / 25

Design Document for

Slim RU Version 1.2

Table of Contents

1. Introduction .......................................................................................... 3

2. Installation............................................................................................ 4

3. Program configuration............................................................................. 5

3.1. GUI............................................................................................... 5

3.1.1. Main window...................................................................................... 5

3.1.2. System window .................................................................................. 5

3.1.2.1. System info ............................................................................... 7

3.1.2.2. Alarm info ................................................................................. 7

3.1.2.3. History info................................................................................ 8

3.1.2.4. Control info................................................................................ 8

3.1.2.5. DIP switch status........................................................................ 8

3.1.2.6. Down load................................................................................. 9

3.2. MMI............................................................................................... 9

3.2.1. MMI connection.................................................................................. 9

3.2.2. General commands........................................................................... 10

3.2.3. Test commands................................................................................ 13

3.2.4. Emergency recovery mo de ................................................................. 22

3.2.4.1. Entering.................................................................................. 22

3.2.4.2. GUI connection ........................................................................ 22

3.2.4.3. Download................................................................................ 23

Reference

User Manual

Revision IR Page 3 / 25

Design Document for

Slim RU Version 1.2

1. Introduction

It is monitor and controls all the functions of Slim-RU series based on graphic user interface
(GUI) or Man Machine Interface (MMI).

Slim-RU GUI program offers straight forward user interface under Windows 2000 or Windows
XP operating system. Therefore it needs only short training course for maintenance
technicians.

Also MMI program performs all functions of GUI. But it has extra commands for detail such as
test purpose command set.

This manual covers all type of Slim-RU series, e.g. totally independent for the series. All
functions described in this document are same. Only operating frequency is different from each
model like bellows.

Models Tx Frequency

STS800-43HM-D

STS1900-43HM-AAD

STS1900-43HM-ABDE

STS1900-43HM-DEFC

869~ 894MHz
1930~1950MHz
1945~1970MHz
1965~1990MHz

* NOTE 1: Before run GUI or MMI program, PC or laptop computer should connect to Slim-

RU with RJ-45 cable.

* NOTE 2: When the cable connects Master Slim-RU, you can handle all Slim-RUs such as

master, slave1, and slave2. But if you connect it to slave 1 or slave 2, you can
handle only it.

Reference

User Manual

Revision IR Page 4 / 25

Design Document for

Slim RU Version 1.2

2. Installation

To install Slim-RU GUI program, double click “Setup_SLIM_RU_2008.06.20_V1.4.exe”. Then

InstallSheild Wizard shows like figure 1. Click “Next” button.

Click “Install” button like figure 2.

Figure1. Initial page

Figure2. Installation

InstallShield Wizard shows the last page when it is done like figure 3. Click “finish” button.

Finally, installation is done. Please confirm file on “start-program-AirWalk-Slim-RU”

Reference

User Manual

Revision IR Page 5 / 25

Figure3. Finish

Design Document for

Slim RU Version 1.2

3. Program configuration

3.1. GUI

3.1.1. Main window

It offers monitoring, setting, and downloading firmware to Slim-RU. You can select

whatever you want to handle.

* NOTE : When the cable connects Master Slim-RU, you can handle all Slim-RUs such as

master, slave1, and slave2. But if you connect it to slave 1 or slave 2, you can
handle only it

Figure4. Main window

* Configuration for serial port

Click “CONFIG” button and set proper communication port and 57600-8-N-1 in the dialog

box

User Manual

3.1.2. System window

It offers monitoring and setting in details

Reference

Revision IR Page 6 / 25

Design Document for

Slim RU Version 1.2

Figure5. System window

For details, it offers “hidden window” with pressing “ctrl + p”

Figure6. Hidden window

User Manual

3.1.2.1. System info

Items Descriptions

F/W Version Shows Frimware Version

H/W Version Shows H/W Version

Description Shows brief system information

PSU TYPE Shows PSU type and information

HPA Power Shows HPA power in dBm

HPA Temp Shows HPA temperature

Equip Temp Shows Slim-RU temperature

Sys Version Shows system version

Sys Capacity Shows Slim-RU capacity

Sys Freq. Shows sys Frequency

Reference

Revision IR Page 7 / 25

Design Document for

Slim RU Version 1.2

3.1.2.2. Alarm info

Items Descriptions

HPA SHUTDOWN Shows HPA shutdown status

HPA ON Shows HPA enable or disable status

HPA FAN Shows fan operation is normal or not

HPA DC FAIL Shows the status of DC power to HPA

LNA_1. Shows LNA_1 status is normal or not

LNA_2 Shows LNA_2 status is normal or not

HPA OVER TEMP Shows HPA over temperature is normal or not

HPA VSWR Shows HPA VSWR is normal or not

HPA OVER POWER Shows HPA output power is over or not

HPA DELETION. Shows HPA deletion or not

LNA DELETION Shows LNA deletion or not

KEEP ALIVE Shows Slim-RU communicates to AW96 normally or not

PSU OVER HEAT Shows power supply is over heat or not

PSU DC FAIL Shows power supply’s DC is normal or not

PSU FAN FAIL Shows power supply’s fan is normal or not

PSU AC FAIL Shows power supply’s AC is normal or not

RPSU OVER HEAT Shows RPSU is over heat or not

RPSU DC FAIL. Shows RPSU DC is normal or not

RPSU FAN FAIL Shows RPSU’s fan is normal or not