Sevylor HUI 100, HUI 200, HUI 400, Colossus 2 Person Boat, Colossus 3 Person Boat Instructions And Warnings

I NFLATABLE BOATS

READ THE FOLLOWING

INSTRUCTIONS AND WARNINGS TO AVOID

DROWNING OR SERIOUS INJURY

WARNING:

• Not a life saving device.

• Not for use by children without adult supervision.

• Always wear an approved Personal Flotation Device
(Life Preserver).

• Do not overload.

• Never tow from another boat or vehicle.

• Use only in water away from debris and obstructions.

• Do not use in high wind, strong currents, open water or
dangerous tides.

• Be familiar with the area you intend to use the product.

• Never allow diving into or from these products.

• Never leave in or near water when not in use.

• Know and follow local water safety rules and boating
regulations.

• Use only in protected waters.

• Do not use this product under the influence of alcohol
or drugs.

• Do not over inflate.

• Follow inflation sequence on the product.

Including the following Model Series:

Colossus™ and HUI

INFLATABLE BOATS

®

®

®

®

INFLATABLE BOATS

®

®

IMPORTANT INFORMATION

The warnings below relate to various situations. Please observe them.

CAUTION!

Denotes a imminent hazard which will result in severe injury if you
do not comply with the instructions.

WARNING!

Reminds you of safety measures which must be observed. Also
denotes unsafe practices which could result in personal injury or
damage to the product or property, if you do not comply with the
instructions.

CAUTION!

It is the owner's responsibility to make sure all users carefully
read and follow the instructions for safe operation of this
product. Observe all local and national laws. Always wear a
Personal Flotation Device approved by the proper authorities.
Please carefully observe the Capacity Plate information which
is printed on the product.

WARNING!

These products are not meant for towing because the extreme
pressure of the water while towing can tear the eyelets and/or
handles. These products are not meant to be used in whitewater.

CAUTION!

Altering the construction of these products could jeopardize the
safety of the occupants and will void the limited warranty.

CAUTION!

Keep boat away from gasoline, battery acid, solvents, etc., as they
can damage the product.

2

INFLATABLE BOATS

®

®

INFLATION INSTRUCTIONS

CAUTION!

Do not over inate. Pressurize product to "Ination Pressure"
stated in the chart for your specic product.

WARNING!

Never use a compressor, CO2 or compressed air to inate the
product. Do not let Your product come into contact with sharp,
pointed objects.

To inate using any Sevylor

®

Pump:

3

1

2

3

4

1. To begin inflation, open external cap and pull firmly on
the lanyard to extend out. This will open internal yellow
seal.

3. When fully inflated, seal valve by pushing in with

adapter nozzle. This will seal the internal yellow
stopper and keep air from escaping while closing cap.
Gently twist adapter while backing hose out of valve.

2. Attach nozzle of hose to inflation end of pump. Insert
adapter nozzle into valve and start pumping.

4. Fully remove pump and hose and close external cap.
Valve should appear depressed into itself.

INFLATABLE BOATS

®

®

IMPORTANT! Inate the product chambers in the following order:

1. Inate the inside all-around safety chamber.

2. Inate the oor chamber(s).

3. Inate the outside main chamber.

The chambers on the product will be numbered to indicate order of
ination also. This order of ination will ensure the proper volume and
buoyancy of the safety chamber.

Note: To inate the mini double lock

TM

valve, which is used on some
of the Sevylor boat oors and seat bottoms, follow the same ina­tion instructions above, using the mini double lockTM valve adapter.
The mini Double Lock™ valve adapter is included with all Sevylor®
pumps. The adapter can be purchased from Customer Service by
calling 1-800-835-3278 (Part Number 5010000707).

CAUTION!

Water temperature and weather do affect the pressure in inatable
products. In cold weather your product will lose some pressure due
to the fact the air will contract. If this occurs, you may want to add

a little air to improve your product’s performance. However, in hot
weather, the air will expand. You must let some air out to prevent
your product from failing due to overpressure. You should avoid
exposing your product to extreme temperatures (hot or cold).

DEFLATION INSTRUCTIONS

Deation instructions using any Sevylor® Pump:

4

Remove nozzle of hose from inflation end and attach to
opposite deflation end of pump. Repeat same steps as
inflation. This will draw the air out quickly.