Seura FS-1 Owner's Manual
WARRANTY REGISTRATION
44"
4
5
16
"
REGISTER FOR
EXTRA BENEFITS
Activate within 30 days of purchase:
seura.com/activate
OUTDOOR TV FLOOR STAND
INSTALLATION GUIDE
Model Number:
FS-1
Compatible with Séura Outdoor TVs:
Shade Series: SHD1-55, SHD1-65, SHD1-75, SHD2-43, SHD2-55, SHD2-65, SHD2-75
Ultra Bright: STM3-55-U, STM3-65-U, STM3-86-U
Safety
Prior to the installation of this product, read all
instructions. Keep this manual for future reference.
This product is designed to mount Seura outdoor
televisions and accessories weighing up to 200 lbs.
to a concrete pad or engineered wooden structure.
CAUTION DO NOT EXCEED MAXIMUM LISTED
WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY
DAMAGE MAY OCCUR.
Warnings:
• Safety measures must be practiced at all times
during the assembly of this product. Use proper
safety equipment and tools for the assembly
procedure to prevent personal injury.
• At least two qualied people should perform the
assembly procedure. Proper installation must
be followed as outlined in these installation
instructions. Personal injury and/or property
damage can result from dropping or mishandling
the TV.
• Ensure that there are no missing or defective
parts upon receipt. Never use defective parts.
• This product contains small parts that could be
a choking hazard.
• Any oor surface used to afx the Séura mount
must be of adequate thickness and stability to
support the included anchors.
• Do not use this product for any purpose other
than to mount a VESA compliant TV on a solid
level ground as outlined in this manual.
2
• When mounted to a wood structure, appropriate
lag screws must be mounted into the supporting
members.
• Make sure there are no water or natural gas lines
underground where the stand is to be located.
Cutting or drilling into a water or gas line may
cause severe property damage or personal injury.
Call your local Digger's Hotline prior to digging.
• Do not install near sources of high heat.
• Do not install on a structure that is prone to
vibration, movement or chance of impact.
Note: The included hardware is for mounting on
concrete or wood joists (wood decking). If you are
uncertain about the nature of your surface, please
consult your hardware or installation professional
for proper mounting.
WARNING: Cancer and Reproductive
Harm: www.p65warnings.ca.gov.
Parts and Tools Required (not included)
¼˝ Drill Bit for
Wood Stud
Hand Held Drill
3
/8 ˝ Concrete Drill Bit*
2
1
1/2”
1/2”
1/2”
1/2”
1/2”
The following tools may be required depending on your particular installation. They are not included.
Level
For Wood Joist Installation For Concrete, Brick and Stone Installation
Stud Sensor
(edge-to-edge stud
nder is recommended)
Tape Measure
Socket Wrench
½” Socket
7/32” Drill Bit 5/16” Masonry Drill Bit
Pencil Power Drill Philips #2
1/2”
½” Combination
Wrench
Screwdriver
(6mm Allen Wrench
for use with 86”
Ultra Bright TV size)
3
Parts Included
Pencil
Level
¼˝ Drill Bit for
Wood Stud
Socket Wrench
Phillips Tip Screwdriver
Tape Measure
Hand Held Drill
Hammer**
3
/8 ˝ Concrete Drill Bit*
½˝ Socket
M10 Socket*
2
1
Wall Plate
(Qty 1)
Universal Tilt Brackets
(Qty 2)
M6 x 60mm Screws
(Qty 2)
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
20
5
16
"
26
1
4
"
14" 14"
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
20
5
16
"
26
1
4
"
14" 14"
Before using the device, please check the following contents of the box for completeness. Illustrations are
not to scale. If any parts are missing or damaged, contact Séura.
WARRANTY REGISTRATION
REGISTER FOR
EXTRA BENEFITS
Activate within 30 days of purchase:
OUTDOOR TV FLOOR STAND
INSTALLATION GUIDE
Manual
seura.com/activate
Model Number:
FS-1
4
Floor Stand
(4) 3/8” x 3” Stainless Steel Concrete Large
Diameter Tapcon Screws
(4) 5/16”
Stainless Steel
Flat Washers
(6) 1/4-20x1/2 Stainless
Steel Security Torx
Screws
Parts Included, Packaged as TW-5
Phillips Tip Screwdriver
Hand Held Drill
Hammer**
M10 Socket*
2
Thread Depth Indicator
(Qty 1)
Universal Washers
(Qty 6)
M6 x 60mm Screws
(Qty 2)
Level
¼˝ Drill Bit for
Wood Stud
Socket Wrench
Phillips Tip Screwdriver
Tape Measure
Hand Held Drill
Hammer**
3
/8˝ Concrete Drill Bit*
½˝ Socket
M10 Socket*
2
1
Thread Depth Indicator
(Qty 1)
Universal Spacers
(Qty 24)
(Qty 6)
Pro Mounting Hardware
Universal Washers
(Qty 6)
Security Barrel
(Qty 1)
Wall Plate
(Qty 1)
(Qty 2)
M6 x 60mm Screws
(Qty 2)
Pencil
Level
¼˝ Drill Bit for
Wood Stud
Socket Wrench
Phillips Tip Screwdriver
Tape Measure
Hand Held Drill
Hammer**
3
/8 ˝ Concrete Drill Bit*
½˝ Socket
M10 Socket*
2
1
Wall Plate
(Qty 1)
Universal Tilt Brackets
(Qty 2)
M6 x 60mm Screws
(Qty 2)
6 Plastic Anchors
(For Wall Mount
3” long
Only)
Mounting Plate
6 Stainless Steel
Lag Screws
5/16”, 3” long
Mounting Tools and Hardware
6 Stainless Steel
Flat Washers
5/16”
4 Security Torx
M6 1.0 x 16mm
Optional security
for use to mount
brackets to TV
2 Tilt Mount TV
Brackets
Screws
T27 Security Torx
Screwdriver
5
4
5
16
"
Features
Tilt Locking Bolts
Allows for tilt
angle of the TV
adjustment.
Floor Stand
Mounting Plate
Fasten to the
oor via 4-6
screws.
Top Leveling
Screws
Allows for leveling
adjustments of the
TV after mounting.
Directional
Mounting Arrows
The arrow lets you
know which edge
is up.
Boom Locking
Screws
Prevents the
TV from being
removed or
dislodged from the
mounting plate.
6
Loading...