Page 1
IP Set-top Box (STB)
Model No.: SP-110
Rev. 1.0
2017.05
1
Page 2
Contents
Attentions ................................................................................ 3
AFETY GUIDE ................................................................................ 3
S
AFETY PRECAUTIONS ................................................................... 3
S
ERVICING ....................................................................................... 3
S
NSPECTION OF ALL A TT ACHMENTS ................................................. 4
I
Preparation ............................................................................. 5
F
RONT PANEL .................................................................................. 5
EAR PANEL .................................................................................... 5
R
EMOTE CONTROLLER .................................................................... 6
R
AY OF CONNECTION ..................................................................... 7
W
Technical Specification .......................................................... 8
Certification Statement ............... Error! Bookmark not defined.
FCC
COMPLIANCE STATEMEN T (UNITED STATES) .................ERROR!
BOOKMARK NOT DEFINED.
STATEMENT ........................ ERROR! BOOKMARK NOT DEFINED.
IC
2
Page 3
Attentions
Safety Guide
1. Must correctly select the power supply voltage, and do not
use the power supply outside the provided voltage value.
2. Before opening the power supply, make sure whether the
power cord and all connections are connected correctly and
completely.
3. if the machine is not used for a long time or is cleaned and
maintained, pull the power plug from the power outlet and
pay attention not to pulling the power cord.
4. When unplugging the power cord, should first close the
current power supply, and pull out the insulation part of the
plug with a hand slowly.
Safety Precautions
1. Do not place the machine in direct sunlight or at the place
near a heat radiation device.
2. Should place the machine on the level and solid surface to
prevent vibration affecting the machine to work properly.
3. Should place the machine at a well-ventilated place, where it
is not humid or dusty near.
4. Wipe the surface of the machine gently with a soft cloth, and
do not to use alcohol, gasoline and other organic solvents to
clean it.
5. Do not use the machine under the weight, impact or
vibration.
Servicing
1． Because the machine has complex internal circuits,
non-professionals are not allowed to open the upper cover of
it to avoid damage to it.
2． Users do not dismantle the machine parts freely, and the
warranty tag will expire if the machine is opened to be
repaired.
3． If it is confirmed to be maintained, please contact the local
warranty department to arrange maintenance.
4． If some parts need to be replaced, repair technicians must
select the original devices in line with the provisions of the
manufacturer.
3
Page 4
Inspection of all attachments
After unpacking the machine, please check it in accordance with
the packing list and confirm whether the attachments contained
are complete. The picture below shows a reference diagram of
the attachments, and various models are equipped with different
attachments and the details of a packing list shall prevail.
The diagram and the diagrams of the components provided
below are schematic, and the physical appearance of all the
components shall prevail.
4
Page 5
Preparation
Front Panel
Rear Panel
5
Page 6
Remote controller
Usage Tips
1． Before the use of a set-top box, please start the network
connection device.
2． During the period of use, please do not pull the power plug
from the power outlet. The machine should be in standby
mode.
3． Install the battery
4． Remote controller of the machine is powered by two 7th
batteries, and make sure the positive and negative pole of
the battery in the process of installation.
5． Operating Range
When the remote controller is in operation, its front-end
should be directed to the infrared receiver window of
the set-top box, and the distance should be less than 6
meters.
6． Attentions
6
Page 7
When the battery lacks of power, replace in timely, or
will affect the sensitivity of the remote control.
If the remote controller is not used for a long time, take
out the battery, so as to avoid corrosion or damage to
the battery caused by liquid leakage.
Do not make the remote control sensor directly
exposed to sunlight or lighting devices, or else it will be
caused to fail.
Do not place the remote controller in the wet or
high-temperature environment, and keep the remote
controller clean.
System Connection
Before connecting to the system, this device and other
relevant equipments should be powered off.
Way of Connection
From STB HDMI
OUT to TV HDMI IN
Connected to the TV
input:
White port - left audio
channel
Red port - right audio
channel
Yellow-port - Video
7
Page 8
Technical Specification
H.265/HEVC main profile
Video format
Audio format
Type PAL / NTSC
H.264/AVC main and high profile,1080P 60fps
HD MPEG2/ MPEG4P2
MPEG-1 Layer 1, 2 and 3
AAC LC, AAC LC+SBR Level 2,
AAC HE Level 2, AAC HE Level 4
Output
Network Card 100/1000 Base-T Ethernet NIC 1 RJ45 Interface
Power adapter input AC 110~240V 50/60Hz
Power adapter
output
Power 12W
Dimension 122mm (W) × 122mm (D) × 32mm (H)
Operating
temperature
HDMI output, Mini AV output, USB port
DC 12V ~ 1A
0℃ ~ 40℃
Certification Statement
FCC compliance statement (United States)
FCC Part 15
This device complies with Part 15 of the Federal
Communications Commission (FCC) Rules. Operation is subject
to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including
interference that may cause undesired operation.
8
Page 9
CAUTION:
Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s
authority to operate this equipment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the manufacturer’s instructions, may cause
interference harmful to radio communications.
There is no guarantee, however, that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio or TV technician for help.
RF Safety Statement
This device is a mobile or fixed location transmitter. The
minimum separation distance between the antenna & radiating
structures of the device and nearby persons is 20 cm, even if
calculations indicate that the MPE distance would be less.
IC Statement ( Canada)
IC Statement per the requirements in RSS-Gen Section 8.4 and
RSP-100 Section 4.
This device complies with Industry Canada ’s license-exempt
RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including
9
Page 10
interference that may cause undesired operation of the device.
French:
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le
fonctionnement.
10
Loading...