Set-N-Serv WIH-27 Specifications
DROP-IN SERVING EQUIPMENT
HOT PAN
Electrically Heated
Individual Control
Item No.
Quantity
c
WIH-17
Large Capacity 12”x27”
Pan Size Opening
Optional Drain & Manifold
c
WIH-27
c
WIH-37
c
WIH-47
c
WIH-57
c
WIH-67
WIH-37 SHOWN
DESCRIPTION:
The WIH series hot pan is an electrically heated
drop-in serving unit that provides the convenience on individually controlled hot food wells,
designed for standard steam table pans. The
pan construction enables the unit to be used
either wet or dry and can be specified with
drains or a complete drain manifold.
The entire hot is efficiently insulated and provided with a factory applied gasket so that it can
be installed in the finest wood fixtures without
marring the counter top. All controls are prewired to a single cord and plug and an apron
mounted remote control panel is optional.
FEATURES:
g
Efficiently insulated to retain heat - protects
fixtures and saves energy
g
Individual thermostat controls - the operator
can control the temperature of each well
separately
g
Factory applied gasket - makes installation
a snap and seals units to the counter top,
thus eliminating seepage
g
Accommodates standard 12” x 20” pans, or
fractional size pans
g
NSF certified; UL recognized
a subsidiary of Mercury Aircraft
1135 NW 159 Dr., Miami, Florida 33169
Tel: (305) 625-2451 or (800) 762-7565 • Fax: (305) 623-0475
SS-3A
HOT PAN
Electrically Heated Individual Control
ELECTRICAL CHARACTERISTICS
MODEL “A” HOT FOOD WELLS
WIH-17 16” 1 29-3/8” X 14-1/4” 65
c
c
WIH-27 29-3/4” 2 29-3/8” X 28” 145
WIH-37 43-1/2” 3 29-3/8” X 41-3/4” 180
c
WIH-47 57-1/4” 4 29-3/8” X 55-1/2” 215
c
WIH-57 71” 5 29-3/8” X 69-1/4” 235
c
c
WIH-67 84-3/4” 6 29-3/8” X 83” 300
A
1 1/8”
3
CUT-OUT
REQUIRED
SHIP WT.
(lbs.)
MODEL VOLTAGE/KW/AMPS
c
WIH-17
c
WIH-27
c
WIH-37
WIH-47
c
c
WIH-57
WIH-67
c
Note: 1000 WATT heating elements are available. CHANGE
N ELECTRICAL required - CONTACT FACTORY.
I
120V - 1.0 KW - 8.3
208V - 1.0 KW - 4.8
240V - 1.0 KW - 4.2
120V - 1.7 KW - 14.2
208V - 1.7 KW - 8.2
240V - 1.7 KW - 7.1
208V - 2.55 KW - 12.3
240V - 2.55 KW - 10.6
208V - 3.4 KW - 16.3
240V - 3.4 KW - 14.2
208V - 4.25 KW - 20.4
240V - 4.25 KW - 17.7
208V - 5.1 KW - 24.5
240V - 5.1 KW - 21.3
NEMA
CONFIGURATION
5-15P
6-15P
6-15P
5-20P
6-15P
6-15P
L6-20P
6-15P
L6-30P
L6-20P
L6-30P
L6-30P
L6-50P
L6-30P
Plan View
9”
3 3/4”
2 1/8”
Elevation
7 1/2”
TOP: Constructed of 18 gauge, type 304 stainless
steel, die stamped with a raised perimeter bead.
There shall be a solid vinyl gasket under the beaded
edge to form a seal to the counter top, thus preventing seepage or marring of the counter top.
HOT FOOD WELLS: Individual hot food wells shall be
18 gauge type 304 stainless steel, one piece construction, all welded, ground and polished to a uniform finish. All corners are coved with a minimum 1/4” radius.
Each well is provided with an 850 watt heating element
(1000 watt on the WIH-17).
INSULATION: The pan is fully insulated with high
density polystyrene, 1” thick on all sides, 2” thick on
the bottom and enclosed with a 22 gauge galvanized
steel outer liner. The entire unit is removable without
the use of tools.
ELECTRICAL: The unit is provided with an individual thermostat control with a pilot light for each well.
All heating elements and controls are pre-wired, and
a 6’ long, 3-wire cord and plug is provided, extending
from the control box located under the unit, on operator’s left. Available for single phase power only.
2 1/2”
27” ID
6” ID
5 1/4”
End View
2 3/4”
SPECIFICATIONS:
NOTE: These units require a special cut-out opening, & will
not fit any standard modular unit.
Specifications subject to change without notice.
ACCESSORIES:
c
Individual drain and valve for each well (add-D to
model number)
c
Individual drain for each well with manifold to
single valve (add-D+M to model number)
Additional valves may be specified - CONTACT
FACTORY
c
1000 watt heating elements in lieu of 850 watt
elements. Change in electrical required -
CONTACT FACTORY
c
* Apron mounted remote controls, CONTACT
FACTORY for opening size
c
AF-Automatic Water Fill
c
* Re-rear extension for manifold (1) required
c
Remote switch
Note: Units with these accessories * are not currently UL listed
a subsidiary of Mercury Aircraft
1135 NW 159 Dr., Miami, Florida 33169
Tel: (305) 625-2451 or (800) 762-7565 • Fax: (305) 623-0475
SS-4A
01/10-SC
Loading...