Including
Needed
1.
PRODUCT MANUAL
RV Tire Pressure Monitor
TPMS
BMPRO
2x
2x
1x
TPMS
2x
1x
Congratulations on the purchase of your TPMS! You need this to get up and running.
1x
Web link
2.
BMPRO - AUSTRALIA
19 Henderson Rd, Knoxfield
VIC 3180
BMPRO - USA
821 E. Windsor Ave, Unit 1
Elkhart, IN 46514
www.teambmpro.com.au
TPMS
Voltage
Type of battery
Duration of battery
Weight
Maximum pressure
3V
CR 1632
2 year
10 gram
8 bar
10m
Before you start, ensure your smartphone is within range of TPMS
3.
4.
A.
Press
in the main menu of the app (A), scan the unique QR Code (B) and follow the instructions in the app
N.B. Internet connection is required
Update time - TPMS
0 km/h
4.4 bar 4.5 bar
> 0 km/
h
B.
10 min
< 1 sec
1 min
5.
Screw anti-theft nut Tighten sensor Screw anti-theft nut
Please note: Only turn the E-pressure valve cap on the tyre when the app asks you to do so!
Remove sensor Place sensor into
special wrench
anticlockwise to fix sensor
Open sensor Replace CR1632 battery
Tighten anti-theft nut
whith the wrench
6.
A.
Go to Settings in the app and set (A), for example, your ideal tyre pressure.
Replace the battery only with type CR1632.
FCC ID: 2ASJH-TPMS
IC : 24777-TPMS
CAN ICES-3 B / NMB-3B
HVIN: TPMS
This device complies with part 15 of the FCC Rules and with Innovation, Science and Economic
Development Canada's license-exempt RSS standards.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio
exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
7.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio
communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications to this unit not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
RF exposure statement
This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled
environment. Thisequipment should be installed and operated with a minimum distance of 20cm
between the radiator and any part ofyour body.
This equipment meets the exemption from the routine evaluation limits in section 2.5 of RSS-102.
It should be installed and operated with a minimum distance of 20cm between the radiator and any part
of your body.
8.
Loading...