Servore ServoGlas 6000 Series, ServoGlas 6000V, ServoGlas 6000X User Manual

Declaration of Conformity. We, the manufacturer ‘Servore Co.,Ltd Korea’ declare that the product(s) listed here is in conformity with the following

standards and directives. The construction file for this product is held by Servore (the Manufacturer) and may be inspected on request by contacting
Servore Co.,Ltd Korea, at: 410-3 Tojin-ri Cheongbuk-myeon Pyeongtaek-si Gyeonggi-do Korea Tel. [phone]~3 or their authorised
representatives. Welding helmets model reference Servoglas 6000 and others as may be claimed by Servore as compliant Autodarkening Welding
Helmets conforming to EN175, 1997 and EN379, 2003. 89/686/EEC

410-3 Tojin-ri Cheongbuk-myeon Pyeongtaek-si Gyeonggi-do Korea

TEL [phone]~3 • FAX [phone]
Home page www.servore.com • E-mail [e-mail]

USER'S MANUAL

AUTO-DARKENING WELDING HELMET

ULTRA LIGHTEN SPEEDY

ULTRA LIGHTEN SPEEDY

AUTO DARKENING WELDING HELMET

AUTO DARKENING WELDING HELMET

SERVOGLAS

www.servore.com

www.servore.com

Instructions for use of ServoGlasⓇ6000
Thank you for purchasing a ServoGlasⓇ6000 welding helmet.

For your own protection, safety and to ensure the maximum service life of your new

Note

helmet please read this manual carefully before use. Misuse or abuse may result in
injury or reduced protection and may also void your warranty.

1. Before Use

ServoGlas 6000 features an easy to use digital control set giving you control over Shade,
Sensitivity, Delay and allowing you to switch the helmet to grind mode. In grind mode the
helmet will not auto darken.

The auto darkening welding filter in the 6000 has been designed for arc welding and gas cutting. It is
suitable for all normal arc welding processes such as MIG, MAG, TIG, SMAW, Plasma Arc and Air Carbon
welding.
Before use the shade control should be adjusted to the appropriate level based upon EN169 (European
Standard specifications or equivalent) or other appropriate safety guidelines. When in doubt please consult
your safety representative or your authorized ServoGlas
The ServoGlas
maximum level indicated on the product and as described in the relevant Standards. This protection is fail­safe and is not compromised by loss of battery power or other electronic failure.
The ServoGlas
the welding arc and respond accordingly resulting in the appropriate darkened filter state as set by the
user and as indicated on the scaled adjustment. Please note that professional judgement may be required
to achieve the best results. When in doubt consult an authorized safety representative or your ServoGlas
distributor and always maintain a conservative attitude towards operation.
Two replaceable lithium batteries type CR2032 (3V) are used as major power sources. An additional solar
cell panel extends battery life and ensures efficient operation. When operating normally the welding
helmet will switch on automatically and switch off automatically to save power a few minutes after the last
welding arc has been detected.
To provide a general check of system status you may wish to set the shade control to 11 and hold the
helmet towards a bright incandescent light source. Under normal circumstances the filter will change
from light to dark state and back to light state again as you move the helmet away. Please note that if you
have any questions or there is any doubt about the performance of your Servore product you should refer
to your authorized safety representative or ServoGlas

Ⓡ

6000 provides continuous protection from ultraviolet and infrared radiation to the

Ⓡ

6000 welding filter cartridge is fitted with four independently operated sensors that detect

■ Always use genuine ServoGlasⓇ6000 front and inside cover plates. Failure to do

Note

so may result in injury and will void the warranty.

■ The ServoGlas
additional protection.

■ Check your helmet for physical damage and test it regularly. If your helmet is
damaged or is not working normally have it tested and repaired before use.

■ Always select the appropriate shade before use according to the type of welding
and current/amperes used. When in doubt refer to your authorized safety
representative.

Ⓡ

6000 is not designed for overhead welding without the use of

Ⓡ

6000 distributor.

Ⓡ

distributor.

Ⓡ

2

SERVOGLAS 6OOO

2. Parts List

The following parts are available from Servore and your authorized ServoGlasⓇ6000 distributor.

Helmet Knob Parts

Part No. Parts

1 Helmet shell
2 Magnifyng Lens(108X51mm)
3 Inner Cover Plate
4 Battery Case
5
6 Front Cover Plate
7 Front Cover

Auto-darkening Welding Filter

3