Server INS Operator’s Manual

CLEANING

BEFORE FIRST USE AND AFTER USE DAILY OR
REGULARLY, DISASSEMBLE AND CLEAN PARTS.
FOR SAFE AND PROPER CARE, AND TO PREVENT
CORROSION, OF PARTS, IT IS IMPORTANT TO
CLEAN, RINSE, SANITIZE, AND DRY PARTS DAILY OR
REGULARLY. FAILURE TO COMPLY WITH ANY OF THESE
INSTRUCTIONS MAY VOID UNIT WARRANTY.

1 SEE DISASSEMBLY.
2 WASH CLEAN ALL PARTS WITH DISHWASHING

DETERGENT AND HOT WATER.

• Clean all conned areas with any supplied

brush(es).

• Do not use scrapers, steel pads, steel wool, or
other cleaning tools that can scratch surfaces.

• Mildly abrasive NYLON or brass brush may be
used to remove any stubborn food or mineral
deposits on interior surfaces of unit.

• Do not use abrasive cleansers.

• Do not use caustic cleansers.

• Do not use cleansing agents with high

concentrations of acid, alkaline or chlorine.

• Do not use ammonia based cleansers.

3 FULLY RINSE ALL WASHED PARTS THOROUGHLY

WITH CLEAR WATER.

• To prevent corrosion on parts, it is important to
thoroughly and fully rinse washed parts.

4 SANITIZE ALL PARTS FOLLOWING LOCAL

SANITIZATION REQUIREMENTS. ALL PARTS IN
CONTACT WITH FOOD MUST BE SANITIZED.

• Allow parts to fully air dry after sanitization.

• Dishwasher safe.

TROUBLESHOOTING

Possible Problems:

• Dispenses little or no product.

• Portion control is not consistent.

• Trigger does not push in.

Possible Solutions:

• Clean unit.

• Ensure unit has adequate level of product to

dispense.

• Ensure unit is assembled correctly.

• Ensure closer plate is installed correctly.

• Ensure that unit is not clogged. Some powder

products can pack and plug.

• Shake unit.

• Ensure correct trigger is installed per product.

SAFETY GUIDELINES

According to food and safety regulations, most foods
must be stored and/or served at certain temperatures
or they could become hazardous. Check with local food

and safety regulators for specic guidelines.

Be aware of the product you are serving and the
temperature the product is required to maintain.
Server Products, Inc. can not be responsible for
the serving of potentially hazardous product.

NSF International listed.

(National Sanitation Foundation)

GENERAL SERVICE, REPAIR,
OR RETURNS

Before sending any item to Server Products for service,
repair, or return, contact Server Products customer
service to request a Return Authorization Number.
Merchandise must be sent to Server Products with this
number.

Merchandise being returned for credit must be in new
and unused condition and not more than 90 days old
and will be subject to a 20% (percent) restocking
charge. Electrical parts (thermostats, heating elements
etc.) are not returnable.

Server Products maintains a fully staffed service
department with highly skilled factory trained personnel.
Service is extremely prompt. Under normal
circumstances, a repaired unit is shipped out the day
after it is received. Labor charges are reasonable.

SERVICE

Contact your dealer or Server Products Inc.
customer service department for the following:

ORDERING REPLACEMENT PARTS

Be prepared to give this information:

• Model Letters/Name/Numbers

• Part Numbers- P/N

• Series Numbers/Letters

• Part Description

This information and other important data is stamped
on the lid or cylinder of pumps or on the bottom or
back side of every unit.

SERVER PRODUCTS
LIMITED WARRANTY

All Server Products equipment is backed by a
two-year limited warranty against defects in materials
and workmanship. For complete warranty information
go to: www.server-products.com

 Server Products Inc.

3601 Pleasant Hill Road
Richfield, WI 53076 USA



262.628.5600



800.558.8722



262.628.5110



[e-mail]



www.server-products.com

MODEL:

INS

TRIGGER
AND
SPRING
ASSEMBLY

01674-REVD�080414�ENGLISH

INSEASONTM,
DROP

LID

BODY

CLOSER PLATE

SPREADER

INSEASONTM,
SPREAD

DISASSEMBLY

ALWAYS CLEAN UNIT THOROUGHLY
BEFORE USE. SEE CLEANING.

1 REMOVE LID FROM UNIT BODY.

• Rotate lid counter clockwise to loosen.

2 EMPTY PRODUCT FROM UNIT.

• Tip over and pour product out of unit body.

3 REMOVE SPREADER FROM UNIT BODY.

• Rotate spreader counter clockwise to loosen.

4 REMOVE CLOSER PLATE FROM UNIT BODY.

• Set unit body upside down on countertop, with
removable parts on top, to disassemble.

• Push trigger and spring assembly into unit body
until space is available for closer plate rim tab to
release from interior space.

• Pull closer plate, by grasp tab, up and out of unit
body.

5 REMOVE TRIGGER AND SPRING ASSEMBLY FROM

SLOT OF UNIT BODY.

• Ensure that spring does not spring up and out of
unit body.

• Hold spring as spring compression is released,
so that spring doesn’t pop out and become lost.

ASSEMBLY

ALWAYS CLEAN UNIT THOROUGHLY BEFORE EACH USE.
SEE DISASSEMBLY AND CLEANING.

Portion Control is preset: 1/3 tsp. for pink and yellow
trigger units, and 1/2 tsp. for green trigger units.

1 INSTALL TRIGGER AND SPRING ASSEMBLY INTO

SLOT OF UNIT BODY.

• Set unit body upside down on countertop.

• Install spring end of trigger and spring assembly

into slot of unit body rst, with trigger portion

amount stamp, on inside of trigger, facing upward.

2 INSTALL CLOSER PLATE INTO UNIT BODY.

• Hold closer plate by grasp tab that extrudes out
from inside middle of closer plate.

• Push and depress trigger and spring assembly into
unit body slot until closer plate rim tab can install
into largest interior space of trigger.

• Ensure that spring does not spring up and out of
unit body.

• Trigger will not depress if closer plate rim tab is
installed into smaller interior spaces of trigger.

• Also align slot on side of closer plate to slide onto
key tab on inside rim of unit body.

3 INSTALL SPREADER ONTO UNIT BODY.

• Rotate spreader clockwise to tighten.

4 FILL UNIT WITH PRODUCT TO DISPENSE.

• Rell with product when product is dispensed down
to rell line.

5 INSTALL LID ONTO UNIT BODY.

• Rotate lid clockwise to tighten.

a Portion Amount Stamp
b Body Slot
c Grasp Tab
d Closer Plate Slot and

Body Rim Key Tab

e Closer Plate Rim Tab
f Closer Plate Rim Tab installing into

Largest Interior Space of Trigger

g Trigger Assembly installing into

Body Slot

h Trigger Assembly depressed into

Body Slot for Closer Plate Rim Tab
to install into Largest Interior Space
of Trigger

i Spreader install
j Spreader rotating clockwise to

secure threading to body

k Lid install and rotating clockwise to

secure threading to body

l Rell Line

PORTION CONTROL

Set portion control by selecting appropriate trigger assembly.
Trigger assembly includes trigger and spring.
Trigger part number and portion amount is stamped on inside of
each trigger.

*Portion amount will be incorrect if unit is not lled with product
above rell line on unit.

Optional Trigger Assemblies:

Trigger

Assembly

87126 87093 Green 1/2 tsp. (.083 oz.) (2.465 mL)
87127 87097 Blue 1/3 tsp. (.056 oz.) (1.642 mL)
87128 87098 Black 1/4 tsp. (.042 oz.) (1.233 mL)
87129 87099 White .15 tsp. (.025 oz.) (0.739 mL)
87131 87104 Burgundy 1/8 tsp. (.021 oz.) (0.616 mL)
87132 87105 Tan 1/16 tsp. (.010 oz.) (0.308 mL)
87133 87108 Pink 1/3 tsp. (.056 oz.) (1.642 mL)
87134 87109 Yellow 1/3 tsp. (.056 oz.) (1.642 mL)

Trigger Color Portion

Amount

Conversion

ASSEMBLY

a

g

b

c

d

e

d

h

c

g

h

a

h

h

k

j

i

l