Bottle Support Kit
86819
SQUEEZE BOTTLES (3)
High-Density, 16 oz
86809
BOTTLE SUPPORT
86811
Thank You
...for purchasing this kit to transform your
topping warmer into a Signature Touch™
Squeeze Bottle Warmer. Drizzle and delight!
SERVE BETTER WITH DISTINCTIVE DESSERTS
SAFETY
According to food and safety regulations, most
foods must be stored and/or served at certain
temperatures or they could become hazardous.
Check with local food and safety regulators for
specific guidelines.
Be aware of the product you are serving and the
temperature the product is required to maintain.
Server Products, Inc. cannot be responsible for
the serving of potentially hazardous product.
CAUTION:
Prevent serious burns and
bottle failure.
DO NOT EXCEED 125° F (52° C).
CLEANING
WASH
all parts properly before use.
SANITIZE
all parts according to local sanitization
requirements. All parts in contact with food
must be sanitized.
YES
Squeeze bottles are dishwasher safe.
Page 2
CARE OF STAINLESS STEEL
• A mildly abrasive nylon or brass brush may
be used to remove any stubborn deposits.
• Fully rinsing and drying all parts can help
prevent corrosion. Elements and minerals in
tap water can accumulate on stainless steel
parts and create corrosion.
• Do not use abrasive, caustic or ammonia
based cleansers.
• Do not use products containing acids,
alkalines, chlorine, or salt. These agents can
corrode stainless steel.
• Do not use metal scrapers or cleaning pads
that could scratch surfaces.
SET-UP
FILL WATER VESSEL BASIN
1
IMPORTANT: Unit must use water.
• Pour 4—6 cups (946-1420mL) of water
into basin.
• Do not overfill.
TIP: Check water levels
throughout the holding period
to ensure even heating.
Filtered water is recommended
to deter corrosion.
INSERT BOTTLE SUPPORT
2
into water vessel basin.
FILL BOTTLES
3
with desired product.
• Product being served must be inside
squeeze bottles.
INSERT BOTTLES
4
into bottle support openings.
TIP: Simplify change-outs
with additional bottles.
Order item #86809.
CAUTION:
Prevent serious burns and
bottle failure.
DO NOT EXCEED 125° F (52° C).
REFER TO WARMER MANUAL
5
for complete instructions included with your
original FS & FSP warmer model.
Manuals are also available at:
www.Server-Products.com
Page 3
TAKE-DOWN
PRESS SWITCH to the “OFF” position.
1
UNPLUG CORD
2
CAUTION- HOT
Allow unit to cool or
take proper care with hot surfaces.
REMOVE BOTTLES
3
REMOVE BOTTLE SUPPORT
4
EMPTY WATER FROM
5
WATER VESSEL BASIN
after each use.
Carefully pour water down a drain.
TIP: Remember to empty the
water each day rather than add—
This will greatly extend the life
of your warmer.
DRY
6
thoroughly with a soft dry cloth.
SERVER PRODUCTS
LIMITED WARRANTY
Server Products equipment is backed by a
two-year limited warranty against defects in
materials and workmanship.
For complete warranty information go to:
www.Server-Products.com
NEED HELP?
Server Products Inc.
3601 Pleasant Hill Road
Richfield, WI 53076 USA
262.628.5600 | 800.558.8722
SPSALES@SERVER-PRODUCTS.COM
Page 4
Proper drying after each use helps
maintain the stainless steel.
GENERAL SERVICE,
REPAIR OR RETURNS
Before sending any item to Server Products for service,
repair, or return, contact Server Products customer
service to request a Return Authorization Number.
Merchandise must be sent to Server Products with this
number. Service is extremely prompt. Typically, units
are repaired and ship out within 48 hours of receipt.
Merchandise being returned for credit must be in new
and unused condition and not more than 90 days old
and will be subject to a 20% restocking charge.
Please be prepared with your Model, Part and
Series Numbers. This information and other
important data is located on the base of the unit.
See cover page for individual part numbers.
Manual #01912-RevC 060617
Loading...