Server 07805 Service Manual

Page 1
Server Express Pumps
MODEL 07805
...for purchasing our Server Express™ Pump. This durable plastic pump is NSF-listed and ADA compliant— requires less than 5 lbs of pressure to dispense.
SIMPLIFY CONDIMENT MANAGEMENT— GO EXPRESS
Page 2
ASSEMBLY
INSERT PINCH VALVE
1
into pump housing.
TIP: Squeeze the pinch valve open before installation to ensure it isn’t stuck shut.
INSTALL DOME
2
Press dome into housing fully.
Ensure valve flap covers bottom opening.
WASH ALL PARTS PROPERLY BEFORE USE. See page 3.
Wrap loop around lower opening to secure dome.
3
4
Page 2
INSTALL TUBE
Lubricate with a small amount of clean water.
Rotate and position until both pegs on housing fit into holes on tube.
INSERT DISCHARGE FITTING
into pump housing discharge tube.
Place loop of fitting around peg on end of discharge tube to secure.
Page 3
SAFETY
According to food and safety regulations, most foods must be stored and/or served at certain temperatures or they could become hazardous. Check with local food and safety regulators for specific guidelines. Server Products, Inc. cannot be responsible for the serving of potentially hazardous product.
DISASSEMBLY
IMPORTANT
Clean, rinse, sanitize, and dry parts daily or regularly to comply with local sanitization requirements.
NSF International (National Sanitation Foundation) lists this pump as: “Not acceptable for dispensing potentially hazardous foods.”
CLEANING
FLUSH & RINSE
1
all pump surfaces with hot water. Place lower end of pump into container of hot water and operate pump until all remaining product is expelled and only hot water is discharged.
DISASSEMBLE & CLEAN
2
all washable parts with soap and hot water. Use brush to clean any confined areas.
RINSE
3
fully with clear water.
SANITIZE
4
all parts according to local sanitization requirements. All parts in contact with food must be sanitized.
AIR DRY
5
all parts fully.
YES!
Use dishwashing soap, hot water and nylon brush
• Dishwasher safe
• Do not use abrasive, caustic or ammonia based cleansers.
• Do not use cleansing agents with high concentrations of acid, alkaline or chlorine.
• Do not use metal scrapers or cleaning pads that could scratch surfaces.
Page 3
Page 4
MODEL 07805
PART QTY DESCRIPTION
07399 1 PUMP DOME, BLUE
07798 1 LARGE PINCH VALVE
07388 1 PUMP HOUSING
07669 1 9½" TUBE
07796 1
DISCHARGE FITTING, .256, MED.
TROUBLESHOOTING
TIP: Squeeze the pinch valve open before installation to ensure it isn’t stuck shut.
DOME 07399
PINCH VALVE 07798
PUMP HOUSING
07388
DISCHARGE FITTING
07796
TUBE
07669
DIFFICULT TO ATTACH PARTS?
• Wet parts with clean water to help fit.
PRODUCT DOESN’T PUMP?
• Ensure pinch valve is inserted in housing.
• Ensure long tube end is submerged in condiment.
• Ensure pump is properly installed in unit.
• Clean pump thoroughly.
DOME POPS OFF?
• Clean thoroughly. Food residue could prevent a tight seal between dome and housing.
• Ensure dome edges are flush with housing.
SERVER PRODUCTS LIMITED WARRANTY
Server Products equipment is backed by a two-year limited warranty against defects in materials and workmanship. For complete warranty information go to:
www.Server-Products.com
GENERAL SERVICE, REPAIR OR RETURNS
Before sending any item to Server Products for service, repair, or return, contact Server Products customer service to request a Return Authorization Number. Merchandise must be sent to Server Products with this number. Service is extremely prompt. Typically, units are repaired and ship out within 48 hours of receipt.
Merchandise being returned for credit must be in new and unused condition and not more than 90 days old and will be subject to a 20% restocking charge.
HELP or ORDERING REPLACEMENT PARTS
Server Products Inc.
3601 Pleasant Hill Road Richfield, WI 53076 USA
262.628.5600 | 800.558.8722
SPSALES@SERVER-PRODUCTS.COM
Page 4
Please be prepared with the Part Numbers for your items. Individual part numbers are listed above.
Manual #01762-RevA 051215
Loading...