
01673-REVA�080414�ENGLISH
MODEL:
SLE-5DI SERVER EXPRESS
SLIM QUINTUPLE DI #1, LJS
07773
TM

SLE-5DI
SERVER EXPRESS
TM
SLIM QUINTUPLE DI #1, LJS
07773
07014(5)
07161(10)
07056(5)
07788
07805(5)
07807(5)
07806(5)
07785
92098(4)
07014 LEVER
07056 ROLLER
07161 PIN, HINGE, SLIC
07785 SHROUD ASSEMBLY
07786 DECAL, QUINTUPLE, LJS-WHITE
07788 LID
07805 PUMP, 55 DURO DOME, NO CONNECTOR
07806 JAR, FOUNTAIN, PLSTC, 2/3, SHORTEN
07807 LID, 2/3, WHITE-PLASTIC, NO THREADS
82049 BRUSH
92098 FOOT, RUBBER, BUTTON

SERVER EXPRESSTM PUMP
55 DURO DOME,
NO CONNECTOR
07805
07399
07798
Part Description
07388 HOUSING, PUMP ASSEMBLY, CLR
07399 DOME, PUMP, .281, 55 DURO
07669 TUBE, PLASTIC, 9 1/2”
07796 FITTING, DISCHARGE, .256-MEDIUM
07798 VALVE, PINCH, ADA PUMP, LARGE
07388
07796
07669

SPECIFIC INFORMATION
Drop-In Units
Drop-In units can be used either on a counter top surface
or can be dropped into an opening in a counter top.
MODEL
Number
07123
Quintuple
PUMP CLEANING
BEFORE FIRST USE AND AFTER USE DAILY OR
REGULARLY, DISASSEMBLE AND CLEAN PARTS.
FOR SAFE AND PROPER CARE, AND TO PREVENT
CORROSION, OF PARTS, IT IS IMPORTANT TO
CLEAN, RINSE, SANITIZE, AND DRY PARTS DAILY OR
REGULARLY. FAILURE TO COMPLY WITH ANY OF THESE
INSTRUCTIONS MAY VOID UNIT WARRANTY.
1 FLUSH AND RINSE ALL INSIDE AND OUTSIDE
SURFACES OF PUMP THOROUGHLY WITH HOT
WATER.
• Place lower end of pump into container of
hot water and operate pump until all (if any)
remaining product is expelled and only hot water
ows from discharge tube. Then remove pump
from container of water to disassemble.
2 DISASSEMBLE PUMP.
3 WASH CLEAN ALL PARTS WITH DISHWASHING
DETERGENT AND HOT WATER.
• Clean all conned areas with any supplied
brush(es).
• Do not use scrapers, steel pads, steel wool, or
other cleaning tools that can scratch surfaces.
• Mildly abrasive NYLON or brass brush may be
used to remove any stubborn food or mineral
deposits on interior surfaces of unit.
• Do not use abrasive cleansers.
• Do not use caustic cleansers.
• Do not use cleansing agents with high
concentrations of acid, alkaline or chlorine.
• Do not use ammonia based cleansers.
4 FULLY RINSE ALL WASHED PARTS THOROUGHLY
WITH CLEAR WATER.
• To prevent corrosion on parts, it is important to
thoroughly and fully rinse washed parts.
5 SANITIZE ALL PARTS FOLLOWING LOCAL
SANITIZATION REQUIREMENTS. ALL PARTS IN
CONTACT WITH FOOD MUST BE SANITIZED.
• Allow parts to fully air dry after sanitization.
• Dishwasher safe.
Recommended
Counter Top Opening Size
8 1/2” x 27 3/16”
GENERAL SERVICE, REPAIR,
OR RETURNS
Before sending any item to Server Products for service,
repair, or return, contact Server Products customer
service to request a Return Authorization Number.
Merchandise must be sent to Server Products with this
number.
Merchandise being returned for credit must be in new
and unused condition and not more than 90 days old
and will be subject to a 20% (percent) restocking
charge. Electrical parts (thermostats, heating elements,
etc.) are not returnable.
Server Products maintains a fully staffed service
department with highly skilled factory trained personnel.
Service is extremely prompt. Under normal
circumstances, a repaired unit is shipped out the day
after it is received. Labor charges are reasonable.
SERVICE
Contact your dealer or Server Products Inc.
customer service department for the following:
ORDERING REPLACEMENT PARTS
Be prepared to give this information:
• Model Letters/Name/Numbers
• Part Numbers- P/N
• Series Numbers/Letters
• Part Description
This information and other important data is stamped
on the lid or cylinder of pumps or on the bottom or
back side of every unit.
SERVER PRODUCTS
LIMITED WARRANTY
All Server Products equipment is backed by a
two-year limited warranty against defects in materials
and workmanship. For complete warranty information
go to: www.server-products.com
Server Products Inc.
3601 Pleasant Hill Road
Richfield, WI 53076 USA
262.628.5600
800.558.8722
262.628.5110
spsales@server-products.com
www.server-products.com