Serpent Model Racing Cars BV f110 SF3 Instruction Manual

1/10 scale 2wd

EP

Instruction

Manual

INTRODUCTION

Serpent developed the Serpent F110 SF3 model car for demanding racers in the highly competitive electric
1/10th scale F1 class, which like all our previous cars, has been designed to win straight from the box.

Featuring a number of very effective features such as a fully adjustable front end, machined aluminium
rear pod, side-links combined with ball-link tube-system to control chassis roll and grip, top-mounted
shockabsorber, quick and easy tweak adjustment and top quality materials throughout, the F110 SF3
should see you in the winners circle in no time. In fact everything associated with this car is of the highest
quality, from the packaging and supplied online manuals, right through to the product and race support.

For latest information about F110 SF3 check on: www.serpent.com/410065

Enjoy racing !

Team Serpent
Multiple World Champions

INSTRUCTIONS

Serpent’s long tradition of excellence extends to the instruction manuals, and this instruction manual is no
exception. The easy-to-follow layout is richly illustrated with 3D-rendered full-color images to make your
building experience quick and easy. Following the instructions will result in a well-built, high-performance
race-car that will soon be able to unleash its full potential at the racetrack. The kit includes bags, with

bagnumbers, which refer to the same step in the manual. Open only the indicated bag(s) per step and nish

that part of the assembly. Remaining parts will be needed lateron in the assembly process.

plaSTIC paRTS

The Serpent moulded parts are very durable and hard. When assembling longer screws in new composite
parts, make sure to use new hex bits in your (power) tools. Pre-threading also helps to avoid screw damage.

SETUp

In certain assembly steps you need to make basic adjustments, which will give you a good initial setup for
your Serpent Spyder SDX4. Fine-tuning the initial setup is an essential part of building a high-performance
racecar like your Serpent Spyder SDX4.

EXplODED VIEWS aND paRTS lIST

The exploded views and parts lists for the Serpent Spyder SDX4z are presented in the Reference Guide
section in the back of this manual. The exploded views show all the parts of a particular assembly step
along with the Serpent part number and hotlink to the Serpent website. Partnumbers in orange indicates
that this part is an optional. Optionals part names and numbers are showed below.

CUSTOmER SERVICE

Serpent has made a strong effort to make this manual as complete and clear as possible. Additional info
may be published in our website: www.serpent.com or you may ask your dealer or the Serpent distributor
for advice, or email Serpent direct: [e-mail]. The Serpent Facebook, Twitter and Youtube pages
give additional means of support and communications.

SafETy

Read and take note of the ‘Read this First section’ before proceeding to assemble the car-kit. This car-kit is
intended for persons aged 16 or older.

REaD ThIS fIRST!

- This is a highly technical hobby product, intended to be used in a safe racing environment. This car
is capable of speeds in excess of 80 km/h or 50mph. Please follow these guidelines when building and
operating this model.

- Parental guidance is required when the builder/user of this car is under 16.

- Follow the building instructions. If in doubt, contact your dealer or importer.

- Be sure to use the proper tools when assembling the car. Always exercise caution when using electric
tools, knives and other sharp objects.

- Be careful when using liquids like lubrication oil, fuel or glue. Do not swallow.

- Follow the manufacturer’s instruction in case you experience irritation after using the product.

- Be careful when operating the car. Stay away from any rotating parts such as wheels, gears and
transmission. Stay away from motor, engine and exhaust pipe system or speedo during and immediately
after use, as these parts may be very hot. We advise to use protective hand cloves.

- Only operate this car in a safe environment, like a special racing track or a closed parking lot. Avoid using
this car on public roads, crowded places or near infants.

- Before operating this car, always check the mechanical status of the car. Also check that the transmitter
and receiver frequencies correspond and are not used by any other racer at the same time. Check that the
batteries of the transmitter and receiver- are fully charged.

- After use, always check all the mechanics of the car. We advise to clean the car immediately after use,
and inspect the parts for wear or fractures. Replace when necessary. Do not use water, methanol, thinner
or other solvents to clean the car.

- Empty the fuel tank (depending on model) if needed and disconnect the receiver battery.

- Store the car in a dry and heated place to avoid corrosion of metal parts.

- Avoid using this car in wet conditions as the water will cause corrosion on the metal parts and bearings
and these parts will cease to function properly. If driven in the wet, ensure that all the electric equipment is
waterproofed and after use, that all moving parts are dried immediately.

CONTENTS

•

FRONTASSEMBLY4

•

REARASSEMBLY    10  

•

CENTRALASSEMBLY    12

•

BALL DIFFA SSEMBLY    15

•

ELEC TRONIC SAS SEMBLY   17

•

SHOCKASSEMBLY    22

•

FINALASSEMBLY25

•

EXPLODEDVIEWS31

•

TEA MSERP ENTN ETW ORK   38

3

hOW TO USE ThE maNUal

Each step contains a variety of numbers, lines, and symbols. The numbers represent the order in
which the parts should be assembled. The lines are described below.

Each step contains a variety of symbols described below.

ICONS DESCRIpTIONlINES DESCRIpTION

Assembly path of one item into another Detail view to explain assembly or order of parts better.

Group of items (within lines) should be
assembled first

Default set-up: This symbol indicates the default setup.

Glue one item to another Silicone grease: apply a small amount of grease to the parts shown.

Direction the item should be moved

Grease: apply a small amount of grease to the parts shown.

Left and right parts should be assembled in the same way.

Connect one item to another

Thread lock: apply a small amount on the parts shown. Before to apply the threadlock,
make sure to degrease the parts very well, as otherwise the threadlock will not work.

Gap between two items Silicone oil: use the indicated silicone oil for the shocks and differentials.

Parts or items not included in the kit.

Optional part, not standard in the kit.

Carefull, read and check very well.

Step number; the order in which you should
assemble the indicated parts

1 32

Apply a small amount of cyano glue. Use wear protection for eyes and hands.Length after assembly

Press/Insert one item into another Oil: apply a small amount of oil to the parts shown.

O

OIL

bag 1

fRONT aSSEmbly

4

STEp 1

M3x8

3x6x1

3x6x1

M3x8

M3x8

3x6x1

As default adjustement of the front ride height should
be assembled 2x 3x6x1 ride height spacers.
The kit includes 4x 3x6x0.5mm ride height spacers
for fine tuning.

3x6x0.5

5

STEp 3STEp 2

FRONTWHEELBASE

LONGER SHORTER

FRONT

REAR

M3x6

M3x6

M3x6

M2.5x6

M2.5x6

1

1

2

3

2

M3x6

M3x6

M2.5x6

6

STEp 4

STEp 5

4.1

4.2

CASTERINSERTSCHART

+ CASTER - CASTER

FRONT

REAR

M3x5

M3x5

M3x6

M3x8

M3x8

5X8X2.5

Flanged

5X8X2.5

Flanged

M3x5

SERVOSAVERACKERMANN
INSERTS

REARWARDFORWARD

+ ACKERMANN- ACKERMANN

M3x6

M3x6

M3x5

M3x8

5X8X2.5 Flanged

bag 2

7

STEp 7STEp 6

4 mm

FRONTCAMBER

8

STEp 9

STEp 8

3x5x2

3x5x2

R2.3

R2.3

M3x8

Nylock
Nut M3

Right steering
block assembly

KINGPININSERTSCHART

0º 1º 2º 3º 4º

King pin angle adjustable from 0 to 4 degrees.

ACKERMANN
POSITION

M3x8 Nylock Nut M3

3x5x2

3x5x2 R2.3

1

3

4

2

9

STEp 11STEp 10

16 mm

STEERINGTRACKRODLENGTH

bag 3

10

REaR aSSEmbly

STEp 12 STEp 13 STEp 14

M3x8 Nylock Nut M3

M3x6

M3x8

M3x6

M3x6

M3x6

M3x6

Nylock

Nut M3

M3x6

bag 4

11

STEp 16STEp 15

M2.2x6

M2.2x6

Nylock
Nut M3

M3x16

M3x16

Nylock Nut M3

REARWINGTOPFLAP
ADJUSTMENT

REARWINGTOPFLAP
ADJUSTMENT

M2.2x6

bag 5

12

CENTRal aSSEmbly

1

1

1

1

2

2

2

2

M3x5

M3x5

M3x5

M3x5

M2x6

M2x6

M2x6

M2x6

Note correct
pivot ball type.

M3x5

M2x6

STEp 17