Sercomm SZKPD04N User Manual

SZ-KPD04N Touch Keypad Installation Guide

Frequency

Zigbee 2.4GHz

Battery Type

CR123A x 2

Key Button Type

Capacitive

Operating Temperature

0 C to 50 C (32°F - 122°F) at 90% RH Non-condensing

Storage Temperature

-20 C to 60 C (-4°F - 140°F)

Dimension

65mm x 101mm x 26mm (2.56" x 3.98" x 1.02")

Proximity Sensor Distance

7 cm (Max)

Introduction

Specification

Pairing Keypad

Figure 1

Figure 2

Figure 3

SZ-KPD04N is a Zigbee touch keypad that controls the security system. It is protected against passcode guessing and supports silent alarm in case of a forced passcode entry. It is connected via the secure Zigbee protocol.

Auto Joining State: A Keypad that does not have a network shall search for a network that is open for joining.

1. Set your security gateway to pairing mode.

2. Slide out battery cover and insert CR123A battery 2 PCS. (Figure 2)

3. The Network / Pairing indicator (Green LED) will be lit for 2 seconds to indicate the sensor is booting successfully

4. It will Network / Pairing indicator (Green LED) blink three times every 5 seconds while attempting to pair with the security panel or home

controller.

5. If network is not found after 100 seconds, the Keypad will go into sleep mode. To wake the pairing mode again, you need to touch any

Keypad button to trigger a paring process, and then sensor will repeat steps from 3 to 4.

6. Slide in battery cover.

Joined State: A Keypad that has joined shall resume the network.

1. Slide out battery cover and insert CR123A battery 2 PCS. (Figure 2)

2. Illuminate the Network / Pairing indicator (Green LED) for 2 seconds to indicate a successful boot.

3. Resume operation with the existing network.

Manual Defaulting: Default a Keypad puts it into a state where it is ready to be joined to a coordinator. The process for manually default a Keypad shall be as follows:

1. Remove 2 CR123A battery, press the Tamper switch and hold it. (Figure 3)

2. Insert CR123A batter. Power it up again. The Kepyad should illuminate the Network / Pairing indicator (Green LED) once all boot up/initialization tasks are complete.

3. Release the tamper switch (in 4 seconds) while the Network / Pairing indicator (Green LED) has been illuminated.

4. The Keypad shall then wipe any knowledge of the previous network and other configuration parameters and begin searching for a new

Normal Function

Weekly Testing

Certification

Operation

Keypad Bracket Instruction

Figure 4

Figure 5

network(Auto Joining State).

Mount the keypad bracket to the wall in the desired location using the included mounting screws and anchors (Figure 4). Align the keypad to wall mount bracket and snap keypad onto bracket. (Figure 5)

Arm Away Button

Press this button and enter your 4 digit security code to arm in away mode. For Example: Press 1,2,3,4 digit and press “Arm away” button. Once the Arm has successfully. The beeper will “beep” on 1 second then off.

Arm Night Button

Press this button and enter your 4 digit security code to arm in night mode. For Example: Press 1,2,3,4 digit and press “Arm Night” button. Once the Arm has successfully. The beeper will “beep” on 1 second then off.

Disarm Button

Press this button and enter your 4 digit security code to disarm mode. For Example: Press 1,2,3,4 digit and press “Disarm” button. Once the Arm has successfully. The beeper will “beep” on 1 second then off.

1. The Network/pairing LED and low battery LED will stay off during the normal operation.

2. The sensor is equipped with a tamper switch. If the cover of sensor is removed, the sensor will send an alarm to the home controller or

security system.

3. Proximity Detection: The keypad is able to detect the user’s presence within 7 cm (Max). Once detected the keypad will awake and

backlit illuminate.

4. Lithium batteries do not charge

5. If enter wrong digit security code, the beeper will “beep” “beep” 2 times.

6. Keypad backlit keep on 5 second once proximity sensor detect user.

To ensure that your system continues to functioning as intended, you must test your system weekly. Please contact your security monitoring company for instructions on how to test your system

+ 1 hidden pages