Sercomm SWDWS02N User Manual

SW-DWS02N Door/Window Sensor Installation Guide

Frequency

908

.42 / 908.40 /

916.00

MHz Batter

y Type

CR2 Battery

1 PCS

Operating

Air

Range

Up to

148 feet line of s

ight Dimension

Device

: 67

mm x 1

9 mm x

20 mm (

2.63

" x

0.74

" x 0.78")

Green LED Indictor

CR2 Battery

Ta

mper Switch

Introduction

Z-Wave Door/Window sensors are designed to secure the perimeter of the residential premise, and provide the
ability to add various automation services. The Z-Wave Door/Window sensor, which consists of a magnet that
attaches to a door or window, will communicate door events to the home security system. When the magnet is
moved away from the sensor, a signal will be sent to the control panel that communicates the changed state to the
security system. Signals can also be used to activate a chime or convenience lighting based on system settings.

Specification

Operating Temperature
Storage Temperature

0° C to 50° C (32°F - 122°F)

-20° C to 60° C (-4°F - 140°F)

Magnet: 45 mm x 8 mm x 15 mm (1.77" x 0.31" x 0.59")

Add (Inclusion) Sensor

For Adding in (Inclusion) a network: Put the Z-Wave Interface Controller into “Add (Inclusion)” mode, and
following its instruction to add SW-DWS02N to your controller. This Door/Window sensor needs to be included
before installation.

1. Pull the exposed plastic tab from the sensor. (Figure 1)

Figure 1

2. The Green LED indicator will be lit for one second to indicate a successful booting.

3. It will blink one time every second while scanning the network (Figure 2).

Figure 2

4. If network is not found after 30 seconds, the sensor will go into sleep mode. To wake the sensor again, you

need to use magnet or tamper (Figure 3) to trigger a paring process, and then sensor will repeat steps from 3 to

4.

Figure 3

Remove

(

Exclusion

)

Sensor

Installation

P

ress

ing the tamper button

Factory

Default

Reset

For Removing from (Exclusion) a network: Put the Z-Wave Interface Controller into “Remove (Exclusion)” mode,
and following its instruction to delete SW-DWS02N to your Z-Wave controller.

1. Remove device rear cover and pressing the tamper button three times within 2 seconds, green LED indicator

should go “On” 0.5 second and enter exclusion mode. (Figure 4).

Figure 4

2. If remove (exclusion) successful, go auto Adding procedure.

3. Node ID has been remove.

1. Pressing the tamper button four times within 2 seconds (Figure 4) and do not release the tamper button in the

4th pressed, and the LED will turn ON.

2. After over 3 seconds the Green LED indicator will turn OFF, then go auto Adding procedure.

3. IDs are excluded and all settings will reset to factory default.

4. Device begin auto Adding (Inclusion) mode.
Note: Use this procedure only in the event that the primary controller is lost.

1. Please make sure that the sensor and magnet is located less than 0.7 inch from each other. For optimal

performance, it is highly recommended to install the Door/Window sensor on the fixed frame and the magnet
on the moving part of the door/window. Place the sensor near the top of the door that close to the opening
edge of the door. This is the mounting location for the sensor.

2. Use the provided double-sided tape on the sensor. Attach the sensor to the door. Press firmly and hold in place

for a few seconds (Figure 5). Secure it with silicone if needed.

Adhesive application surface: Acrylic, Glass

Figure 5

Aluminum and Stainless steel…etc.

3. Use provided double-sided tape on the magnet. Make sure the alignment of both sensor and magnet alignment

mark are facing each other (Figure 6). Press firmly and hold in place for a few seconds. Secure it with
silicone if needed.