This Chapter provides an overview of the Outdoor Network Camera's features and capabilities.
Congratulations on the purchase of your new Outdoor Network Camera. The Outdoor Network
Camera is a Water/Dust Proof device, which is used for home monitoring and security.
Package Contents
The following items should be included:
• The Outdoor Network Camera Unit
• Antenna
• Power Adapter
• A Stand
• Default kit
If any of the above items are damaged or missing, please contact your dealer immediately.
Features
• Support Dust Proof and Water Proof IP65
• Provide MPEG4 Simple Profile (up to 30fps) and Motion-JPEG video streams simultane-
ously (up to 30fps)
• Streaming resolution at VGA (640x480), QVGA (320x240) and QQVGA (160x120).
• Support Day /Night mode by auto IR switcher as well as 8 IR LED
Low Light Sensitivity is 0.5 Lux without IR LED
Low Light Sensitivity is 0.1 Lux with IR LED
• Support H/W Motion Detection by PIR Sensor.
• Support full duplex bi-directions audio with Echo Cancellation function
• Support IEEE 802.11b/g.
• Support Motion Detection by analyzing the video stream.
• Support user-defined HTTP CGI for the HTTP notification action.
• Image controls
Sharpness, Brightness, Image Quality, Time Stamp and Text Overlay, image flip and mirror control.
•Alarm Event includes File upload via FTP, HTTP, email notification and FTP event
recording.
1
Wireless Adapter User Guide
LEDs
Front-mounted LEDs
The Outdoor Network Camera has 4 LEDs.
Power
Active
Network / WPS
Microphone
• On (Green)- Power On
• Off - Power Off
• Flashing - The device is rebooting.
• Off - No user is viewing the camera.
• Blinking - User(s) is viewing the camera.
• On (Green)- LAN connection established.
• Off - Wireless or LAN is not connected.
• Flashing (Green) - Data is being transmitted or received via the
corresponding LAN (hub) port.
•On (Amber)- If the LED is on, the WPS is not processing success-
fully.
• Flashing (Amber) - WPS function is being processed.
• On - Microphone function is enabled.
• Off - Microphone function is disabled.
2
Introduction
Rear Panel
LAN Port
RESET
POWER Switch
Power Port
Use standard LAN cables (RJ45 connectors) to connect your PCs to
these ports.
Click this button to setup WPS Auto mode and pin mode, or reset all
setting to factory default. After Reset switch is pressed, system will take
following actions:
•Press once (less than 3 seconds) under Wireless connection, system
will be in WPS PBC model (Auto mode).
•Press and hold over 3 seconds (less than 10 seconds) under Wire-
less connection, system will be in WPS PIN code mode (8 digital,
generated from last 3 byte of MAC address)
•Press and hold over 10 seconds, reset to manufacturer default value
and reboot.
Push the button down to power on the device
Connect the supplied power adapter here.
3
Chapter 2
Initial Installation
2
This Chapter covers the software installation of the Outdoor Network Camera.
Requirements
• Network cables. Use standard 10/100BaseT network (UTP) cables with RJ45 connectors.
Procedure
1. Choose an Installation Site
Select a suitable place to install the Outdoor Network Camera.
2. Connect LAN Cables
Use standard LAN cables to connect devices to the LAN port on the Outdoor Network
Camera.
4. Power Up
Connect the supplied power adapter to the Outdoor Network Camera. Use only the power
adapter provided. Using a different one may cause hardware damage.
Push the Power switch down to turn on the device.
5. Check the LEDs
•The Power LED should be ON.
4
Initial Installation
•The Network LED should be ON (provided the PC is also ON.)
5
Chapter 3
Specifications
This Chapter provides specifications for the Outdoor Network Camera.
Hardware features
Feature Description
CPU
Flash ROM 4 Mbytes
SDRAM 32 Mbytes SDRAM
LAN DM9102H, Ethernet 10/100BaseT, Auto-MDIX,
WiFi IEEE 802.11b/g standard
Max 50m line of sight, with no interference
External Antenna with 4.2dBi, water proof
Indicators
SC1100, ARM9 based, 32bit-192Mhz base clock
Hardware MPEG-4 SP/MJPEG Encoders
Power Green
3
Connectors
External Power
Adapter
Power Consumption
Audio
Microphone/Speaker
Codec
Audio option
Active Green
Network Green/ Amber
Microphone Green
Ethernet, RJ45 connector
Reset Button, Tack switch
Power on/off button
DC Power,
5V/2A, 10W, 100~240 VAC, Switching
2.5mm Phone Jack, 180 Degree
Estimated 5W
Bi-directional, built in mic and speaker
G.726 (ADPCM)/G7.11 (PCM)
Software controlled on/off via web interface and firmware
Audio recoding/playback
This device has been designed to operate with the antennas listed below, and having a
maximum gain of [4.2] dB. Antennas not included in this list or having a gain greater
than [4.2] dB are strictly prohibited for use with this device. The required antenna
impedance is [50] ohms.
10
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.