Sercomm 0YC01 Users Manual

Network Camera

User’s Guide

Table of Contents

CHAPTER 1 INTRODUCTION.............................................................................................. 1

Overview ............................................................................................................................ 1

Physical Details - Network Camera ................................................................................. 4

Package Contents .............................................................................................................. 6

CHAPTER 2 BASIC SETUP ...................................................................................................7

System Requirements........................................................................................................ 7

Installation - Network Camera......................................................................................... 8

Setup using the Windows Wizard.................................................................................... 9

CHAPTER 3 VIEWING LIVE VIDEO ................................................................................ 14

Overview ..........................................................................................................................14

Requirements................................................................................................................... 14

Connecting to a Camera on your LAN..........................................................................14

Connecting to a Camera via the Internet ...................................................................... 16

Viewing Live Video .........................................................................................................18

Setting the Focus.............................................................................................................. 19

CHAPTER 4 ADVANCED VIEWING SETUP ................................................................... 20

Introduction ..................................................................................................................... 20

Adjusting the Video Image ............................................................................................. 20

Controlling User Access to the Video Stream ............................................................... 24

Making Video available from the Internet.................................................................... 25

Viewing Live Video via the Internet .............................................................................. 27

Motion Detection Alerts.................................................................................................. 29

CHAPTER 5 WEB-BASED MANAGEMENT ....................................................................30

Introduction ..................................................................................................................... 30

Connecting to Network Camera..................................................................................... 30

Welcome Screen............................................................................................................... 31

Administration Menu...................................................................................................... 32

System Screen .................................................................................................................. 33

Network Screen................................................................................................................ 35

Wireless Screen (Wireless Model Only) ........................................................................38

DDNS Screen ................................................................................................................... 40

IP Filter Screen................................................................................................................42

I/O Port Screen ................................................................................................................ 43

Video & Audio Screen..................................................................................................... 44

Video Access Screen ........................................................................................................ 47

User Database Screen...................................................................................................... 49

Motion Detection Screen.................................................................................................51

E-Mail Screen ..................................................................................................................52

FTP Screen.......................................................................................................................54

Instant Messaging Screen ...............................................................................................55

Event Trigger Screen ......................................................................................................57

Maintenance Screen ........................................................................................................ 59

Status Screen.................................................................................................................... 61

Log Screen........................................................................................................................ 63

CHAPTER 6 WINDOWS VIEWING/RECORDING UTILITY........................................ 64

Overview ..........................................................................................................................64

Installation ....................................................................................................................... 64

System Tray Icon............................................................................................................. 65

Main Screen .....................................................................................................................65

Camera Setup ..................................................................................................................66

Main Screen .....................................................................................................................70

Recording Video .............................................................................................................. 72

CHAPTER 7 TROUBLESHOOTING .................................................................................. 77

Overview .......................................................................................................................... 77

Problems........................................................................................................................... 77

APPENDIX A SPECIFICATIONS........................................................................................ 80

Network Camera .............................................................................................................80

Regulatory Approvals ..................................................................................................... 80

Copyright Notice.............................................................................................................. 82

APPENDIX B STREAMING VIDEO/AUDIO SOLUTION............................................... 98

Overview ..........................................................................................................................98

Streaming Video/Audio through Internet Camera....................................................... 98

P/N: 9560WL0001

Document Version: 1.0

All trademarks and trade names are the properties of their respective owners.

Chapter 1

Introduction

This Chapter provides details of the Network Camera's features, components and capabilities.

Overview

The Network Camera has an Integrated Microcomputer and a high quality Sony Progressive CCD Image-Sensor, enabling it to display high quality live streaming video over your wired LAN, the Internet, and for the Network Camera, an 802.11g Wireless LAN.

Using enhanced MPEG-4 technologies, the Network Camera is able to stream high quality video and two-way audio directly to your PC. The high compression capabilities of MPEG-4 reduce network bandwidth requirements to amazingly low levels.

A convenient and user-friendly Windows program is provided for both viewing and recording video. If necessary, you can even view video using your Web Browser, on a variety of software platforms.

Figure 1: Network Camera

Features

x Dual Stream Live Video to Multiple Users. The MPEG4 and JPEG encoders built

into the camera generate a ready-to-view video stream. Just connect to the camera using your Web browser or the provided Windows utility to view live video.

Night/Day Switch Support. Supporting IR-cut filter, the Network Camera can get better

x

video quality even in the nighttime.

x Suitable for Home, Business or Public Facilities. Whether for Home, Business or

Public Facility surveillance, the Network Camera has the features you need.

Multi-Protocol Support. Supporting TCP/IP networking, SMTP (E-mail), HTTP and

x

other Internet related protocols, the Network Camera can be easily integrated into your existing network.

Easy Configuration. A Windows-based Wizard is provided for initial setup.

x

Subsequent administration and management can be performed using a standard web browser. The administrator can configure and manage the Network Camera via the LAN or Internet.

x Viewing/Recording Utility. A user-friendly Windows utility is provided for viewing

live video. For periods when you are absent, or for scheduled recording, this application also allows you to record video on your PC. Use the Playback function of the supplied Windows utility to view the recorded files.

x Motion Detection. This feature can detect motion in the field of view. The Network

Camera will compare consecutive frames to detect changes caused by the movement of large objects. Motion detection alarm can be triggered via e-mail, FTP, instant messaging and/or an external alarm device.

x Flexible Scheduling. You can limit access to the video stream to specified times using

a flexible scheduling system. The Motion Detection feature can also have its own schedule, so it is active only when required.

Syslog Support. If you have a Syslog Server, the Network Camera can send its log data

x

to your Syslog Server.

Audio Support. You can listen as well as look! Audio is encoded with the video if

x

desired. You can use either the built-in microphone or an external microphone.

IP Filter. Use the IP Filter to block/accept access to the IP addresses.

x

User-definable HTTP/ HTTPS port number. This allows Internet Gateways to use

x

"port mapping" so the Network Camera and a Web Server can share the same Internet IP address.

DDNS Support. In order to view video over the Internet, users must know the Internet

x

IP address of the gateway used by the Network Camera. But if the Gateway has a dynamic IP address, DDNS (Dynamic DNS) is required. Since many existing Gateways do not support DDNS, this function is incorporated into the Network Camera.

x NTP (Network-Time-Protocol) Support. NTP allows the Network Camera to

calibrate its internal clock from an Internet Time-Server. This ensures that the time stamp on Video from the Network Camera will be correct.

Security Features

x User Authentication. If desired, access to live video can be restricted to known users.

Users will have to enter their username and password before being able to view the video stream. User authentication is not required if the Multicast feature is enabled.

Password-Protected Configuration. Configuration data can be password protected, so

x

that it only be changed by the Network Camera Administrator.

Wireless Features (Wireless Model only)

x Standards Compliant. The Network Camera complies with the IEEE802.11g (DSSS)

specifications for Wireless LANs.

Supports both 802.11b and 802.11g Standards. The Network Camera supports both

x

802.11b and 802.11g standards.

Speeds to 54Mbps. All speeds up to the 802.11g maximum of 54Mbps are supported.

x

Wired and Wireless Network Support. The Network Camera supports either wired and

x

wireless transmission.

WEP Support. Full WEP support (64/128 Bit) on the Wireless interface is provided.

x

WPA/WPA2-Personal Support. The WPA/WPA2-Personal standard is also supported,

x

allowing advanced encryption of wireless data.

Physical Details - Network Camera

Front - Network Camera

CS Mount Lens

Microphone

Power LED (Amber)

Network LED (Green)

Adjust focus manually by turning the front lens clear. You also should ensure that the lens cover remain clean. The image quality is degraded if the lens cover is dirty or smudged.

The built-in microphone is mounted on the front. There is also a connection for an external microphone on the rear. Connecting an external microphone will disable the built-in microphone.

On - Power on.

Off - No power.

Blinking - The Power LED will blink during start up. This will take

15 to 20 seconds.

On - Wireless or LAN connection is detected.

Off - Wireless or LAN connection is not detected

Blinking - Data is being transmitted or received via the LAN or

Wireless connection.

Rear - Network Camera

Antenna

Reset Button

For Wireless model, attach the supplied antenna here. The antenna is adjustable; best results are usually obtained with the antenna positioned vertically.

This button is recessed; you need a pin or paper clip can be used to depress it. It can be activated at any time the camera is in the "ready" mode.

x WPS PBC Mode. For the Wireless Model, when pressed and

released (less then 3 seconds), the Network Camera will be in the WPS PBC mode (Auto link mode).

x WPS Pin Code Mode. For the Wireless Model, when pressed

and held for over 3 seconds, the Network Camera will be in the WPS Pin Code mode.

x Reset to manufacturer default value and reboot. When

pressed and held over 10 seconds, the settings of Network Camera will be set to their default values.

Note:

After this procedure is completed, the Power LED will blink three times to confirm that the reset was completed successfully.

LAN port

Use a standard LAN cable to connect your Network Camera to a 10/100BaseT hub or switch.

Note:

x Attaching the LAN cable will disable the Wireless interface.

Only 1 interface can be active at any time.

x The LAN cable should only be connected or disconnected when

the camera is powered OFF. Attaching or detaching the LAN cable while the camera is powered on does NOT switch the interface between wired and wireless.

Power Input

GPIO

MIC In

SPKR out

Connect the supplied 12V power adapter here. Do not use other power adapters; doing so may damage the camera.

The GPIO terminal block includes 2 input ports and 2 output ports.

If required, an external microphone can be attached here. Attaching a microphone here will disable the built-in microphone on the front. Microphones which are designed to be used with PCs are usually compatible with this microphone input.

If required, an external speaker can be attached here.

Package Contents

The following items should be included: If any of these items are damaged or missing, please contact your dealer immediately.

1. Network Camera

2. Antennae (Wireless Model only)

3. Lens

4. Stand

5. Allen Wrench

6. Power adapter

7. Installation CD-ROM

8. Quick Installation Guide

CS Mount Lens

The following list contains the CS Mount lens which have been tested on the Network Camera:

TOPICA

0416-M1 0816-M1 TP-0550WOE TP-0560WOE

Computar

T2Z3514CS-2

SpaceCom

TV308DC-2 TAV2712DC

Pentax

C70220DCPS

Kowa

LMVZ38A-IR

Fujinon

YV2.8x2.8LA-SA2L

Tamron

13VG308AS 13VG2812AS 12VG412ASIR 12FM04CST 13VM308ASIR 13FM04IR

Chapter 2

Basic Setup

This Chapter provides details of installing and configuring the Network Camera.

System Requirements

x To use the wired LAN interface, a standard 10/100BaseT hub or switch and network cable

is required.

x To use the Wireless interface on the on the Wireless Model, other Wireless devices must

be compliant with the IEEE802.11b or IEEE802.11g specifications. All Wireless stations must use compatible settings.

The default Wireless settings are:

Mode: Infrastructure ESSID: ANY Wireless Security: Disabled Domain: USA Channel No.: Auto

Installation - Network Camera

1. Assemble the Camera

Attach the lens to the Network Camera. On the Wireless Model, screw the antenna to the rear mounting point, and set the antenna to the upright position to improve wireless reception.

2. Connect the LAN Cable

Connect the Network Camera to a 10/100BaseT hub or switch, using a standard LAN cable.

For Wireless model, plugging in the LAN cable will disable the Wireless interface. Only 1 interface can be active at any time.

The LAN cable should only be connected or disconnected when the camera is powered OFF. Attaching or detaching the LAN cable while the camera is powered on does NOT switch the interface between wired and wireless.

The first time you connect to the camera, you should connect the LAN cable and configure the Network Camera with appropriate settings. Then you can unplug the LAN cable and power off the camera. The Network Camera will be in wireless interface when you power on the camera again.

3. Power Up

Connect the supplied 12Vpower adapter to the Network Camera and power up. Use only the power adapter provided. Using a different one may cause hardware damage.

4. Check the LEDs

x The Power LED will turn on briefly, then start blinking. It will blink during startup, which

takes 15 to 20 seconds. After startup is completed, the Power LED should remain ON.

x The Network LED should be ON.

For more information, refer to Physical Details - Network Camera in Chapter 1.

Setup using the Windows Wizard

Initial setup should be performed using the supplied Windows-based setup Wizard. This program can locate the Network Camera even if its IP address is invalid for your network. You can then configure the Network Camera with appropriate TCP/IP settings for your LAN.

Subsequent administration can be performed with your Web browser, as explained in Chapter 5 - Web-based Management.

Setup Procedure

1. Insert the supplied CD-ROM into your drive. If the setup program does not start automatically, run Setup.exe in the root folder.

x You will see the Welcome screen shown below.

x Click the Setup Camera button to start the setup Wizard

Figure 2: Welcome Screen

2. The next screen, shown below, will list all the Network Cameras on your LAN.

Figure 3: Camera List Screen

x Select the desired Camera from the list on the left. The current settings for the selected

Camera will be displayed in the table on the right.

x Click Next to continue.

3. You will be prompted to enter the Administrator Name and Administrator Password, as shown below.

x If using the default values, enter administrator for the name, and leave the

password blank.

x Otherwise, enter the Administrator Name and Administrator Password set on the

Admin Login screen.

Figure 4: Password Dialog

4. On the following IP Address Settings screen, shown below, choose Fixed IP or Dynamic IP.

Figure 5: Fixed or Dynamic IP Selection

x Fixed IP is recommended, and can always be used.

x Dynamic IP can only be used if your LAN has a DCHP Server.

Click Next to continue.

5. If you chose Fixed IP Address, the following TCP/IP Settings screen will be displayed.

Figure 6: TCP/IP Settings

x Enter an unused IP Address from within the address range used on your LAN.

x The Subnet Mask and Default Gateway fields must match the values used by PCs on

your LAN.

x The Primary DNS address is required in order to use the E-mail alert or Dynamic

DNS features. Enter the DNS (Domain Name Server) address recommended by your ISP.

x The Secondary DNS is optional. If provided, it will be used if the Primary DNS is

unavailable.

Click Next to continue.

6. This screen allows you to enter a suitable Description, and set the correct Time Zone,

Local Date, and Local Time. Make any desired changes, then click Next to continue.

Figure 7: Camera Settings

7. The next screen, shown below, displays all details of the Network Camera.

x Click Next if the settings are correct

x Click Back to modify any incorrect values.

Figure 8: Save Settings

8. Click OK to confirm that you want to save the new settings. If you want to cancel your changes, click Cancel.

Figure 9: Confirm Screen

9. After clicking Next, you will see the screen below.

Figure 10: Final Screen

Clicking the Install Utility button will install the Viewing/Recording utility described in Chapter 6 - Windows Viewing/Recording Utility.

10. Click Exit to end the Wizard. Setup is now complete.

Chapter 3

Viewing Live Video

This Chapter provides basic information about viewing live video.

Overview

After finishing setup via the Windows-based Wizard, all LAN users can view live video using Internet Explorer on Windows.

This Chapter has details of viewing live video using Internet Explorer.

But many other powerful features and options are available:

x To view multiple cameras simultaneously, or record video (either interactively or by

schedule), you should install the Windows Viewing/Recording utility. Refer to Chapter 6 - Windows Viewing/Recording Utility for details on installing and using this program.

x The camera administrator can also adjust the Video Stream, and restrict access to the video

stream to known users by requiring viewers to supply a username and password. See Chapter 4 - Advanced Viewing Setup for details.

x To make Live Video from the camera available via the Internet, your Internet Gateway or

Router must be configured correctly. See Making Video available from the Internet in Chapter 4 - Advanced Viewing Setup for details.

Requirements

To view the live video stream generated by the Network Camera, you need to meet the following requirements:

x Windows 98/98SE, Windows 2000, Windows XP, Windows Vista.

x Internet Explorer 5.5 or later.

Connecting to a Camera on your LAN

To establish a connection from your PC to the Network Camera:

1. Use the Windows utility to get the IP address of the Network Camera.

2. Start Internet Explorer.

3. In the Address box, enter "HTTP://" and the IP Address of the Network Camera.

4. When you connect, the following screen will be displayed.

Figure 11: Home Screen

5. Click View Video.

6. If the Administrator has restricted access to known users, you will then be prompted for a username and password. Enter the name and password assigned to you by the Network Camera administrator.

7. The first time you connect to the camera, you will be prompted to install an ActiveX component (OCX or CAB file), as in the example below.

You must install this ActiveX component (OCX or CAB file) in order to view the Video stream in Internet Explorer. Click the "Yes" button to install the ActiveX component.

Figure 12: ActiveX OCX Prompt

8. Video will start playing automatically. There may be a delay of a few seconds while the video stream is buffered.

Connecting to a Camera via the Internet

You can NOT connect to a camera via the Internet unless the camera Administrator has configured both the camera and the Internet Gateway/Router used by the camera.

See Making Video available from the Internet in Chapter 4 - Advanced Viewing Setup for details of the required configuration.

Also, you need a broadband Internet connection to view video effectively. Dial-up connections are NOT supported.

To establish a connection from your PC to the Network Camera via the Internet:

1. Obtain the following information from the Administrator of the camera you wish to connect to:

x Internet IP Address or Domain Name of the camera.

x Port number for HTTP connections.

x Login (username, password) if required.

2. Start Internet Explorer.

3. In the Address box, enter the following:

HTTP://Internet_Address:port_number

Where Internet_Address is the Internet IP address or Domain Name of the camera, and port_number is the port number used for HTTP (Web) connections to the camera.

Examples using an IP address:

HTTP://203.70.212.52:1024 Where the Internet IP address is 203.70.212.52 and the HTTP port number is 1024.

Example using a Domain Name:

HTTP://mycamera.dyndns.tv:1024

Where the Domain name (using DDNS in this example) is mycamera.dyndns.tv and the HTTP port number is 1024.

4. When you connect, the following screen will be displayed.

Figure 13: Home Screen

5. Click View Video.

6. If the Administrator has restricted access to known users, you will then be prompted for a username and password. Enter the name and password assigned to you by the Network Camera administrator.

7. The first time you connect to the camera, you will be prompted to install an ActiveX component (OCX or CAB file), as in the example below.

You must install this ActiveX component (OCX or CAB file) in order to view the Video stream in Internet Explorer. Click the "Yes" button to install the ActiveX component.

Figure 14: ActiveX OCX Prompt

8. Video will start playing automatically. There may be a delay of a few seconds while the video stream is buffered.

Viewing Live Video

After installing the ActiveX component, you be able to view the live video stream in its own window, as shown below.

Adjust focus manually by turning the front lens until the video becomes clear.

Figure 15: View Video Screen

There are a number of options available on this screen, accessed by select list, button or icon. See the table below for details.

General Options

These options are always available, regardless of the type of camera you are connected to.

ON. Click this to set the output I/O port to ON mode.

OFF. Click this to set the output I/O port to OFF mode.

Day. Use this to get better video quality during the daytime.

Night. Use this to get better video quality during the nighttime.

Resolution. Select the desired video resolution format.

Zoom. A digital zoom feature is available. To zoom in on a section of the

window, click this icon. Then use your mouse to select the section you want to magnify. Click the icon again to disable the zoom feature.

Snapshot. Click this to take a single JPEG "snapshot" image of the current video.

Flip. Click this to have the image swapped top-to-bottom.

Mirror. Click this to have the image swapped left-to-right.

Audio On. This icon is displayed if audio is On. Click on the icon to turn

audio Off.

Audio Upload. This icon is displayed when the Speaker (Audio & Video screen) is enabled. Use this slider to adjust the volume.

Volume. Use this slider to adjust the volume.

Setup. Select the desired setup format from the drop-down list.

Setting the Focus

After viewing the live video, you need to adjust focus manually by turning the front lens until the video becomes clear.

Chapter 4

Advanced Viewing Setup

This Chapter provides information about the optional settings and features for viewing video via the Network Camera. This Chapter is for the Camera Administrator only.

Introduction

This chapter describes some additional settings and options for viewing live Video:

x Adjusting the video image

x Controlling user access to the live video stream

x Making video available from the Internet

x Using the Motion Detection feature

Adjusting the Video Image

If necessary, the Network Camera Administrator can adjust the Video image. Settings are provided for:

x Resolution - Select the desired resolution format. The larger sizes require greater

bandwidth.

x Video quality - This determines the degree of compression applied to the Video stream.

Higher quality requires greater bandwidth.

x Frame Rate - Select the max frame rate to determine the bandwidth required by the video

stream.

x Power Line frequency - Select 50Hz or 60Hz power line frequency, as used in your

region. The correct setting will improve the picture quality under florescent lighting.

x White Balance - Select the correct white balance for your environment.

x Brightness - Adjust the brightness of the image.

x Sharpness - Select the desired option for the sharpness.

x Contrast - Select the desired option for the contrast. You can select a contrast value

between -3 and 3.

x Microphone - If enabled, audio can be included in the video stream.

x Time Stamp - If enabled, the time will be displayed on the Video image.

x Text Overlay - If enabled, up to 20 characters can be superimposed on the Video image.

This is useful for identifying the camera.

x Day/Night Switch - If enabled, the Network Camera can get better video quality even in

the nighttime.

To Adjust the Video Image:

1. Connect to the Web-based interface of the Network Camera. (See Chapter 5 - Web-based Management for details.)

2. Select Video & Audio. You will see a screen like the example below.

Figure 16: Video & Audio Screen

3. Make the required adjustments, as explained below, and save your changes.

MPEG-4 Settings

Resolution

Select the desired video resolution format. The default resolution is set to 320*240.

Video Quality Control

x Constant Bit Rate: Select the desired bit rate. The default is set

to 1.2 Mbps.

x Fixed Quality: Select the desired option. The default fix quality

is set to Normal.

Max. Frame Rate

MJPEG Settings

Resolution

Fixed Video Quality

Max. Frame Rate

Mobil Settings

Enable Mobil Streaming

Resolution

Video Quality Control

Max. Frame Rate

Access Code

Video Adjustments

Select the desired Maximum frame rate for the video stream.

Select the desired video resolution format. The default resolution is set to 320*240.

Select the desired fix quality. The default fix quality is set to Normal.

Select the desired Maximum frame rate for the video stream.

Enable streaming video for the mobile device by checking this checkbox.

The default resolution is set to 160x120.

x Constant Bit Rate: Select the desired fix bit rate.

x Fixed Quality: Select the desired option. The default fix quality

is set to Normal.

Select the desired Maximum frame rate for the video stream. The default maximum frame rate is set to 15 fps.

Enter the code for accessing the live video from camera through cell phone connection.

Power line frequency

White Balance

Brightness

Sharpness

Contrast

Options

Microphone

Audio Type

Speaker

Time Stamp

Select the power line frequency (50Hz or 60Hz) used in your region, to improve the picture quality under florescent lighting.

Select the desired option to match the current environment and lighting.

If necessary, you can adjust the brightness to obtain a better image. For example, if the camera is facing a bright light, the image may be too dark. In this case, you can increase the brightness.

Select the desired option for the sharpness. You can select a Sharpness value between -3 and 3.

Select the desired option for the contrast. You can select a Contrast value between -3 and 3.

Enable audio by checking this checkbox. Using Audio will increase the bandwidth requirements slightly.

Select the desired audio type.

Enable speaker feature by checking this checkbox.

If enabled, the current time will be displayed on the Video image.

Text Overlay

Day/Night Switch

Enable this setting if you want text to be displayed on the Video image, and enter the desired text - up to 20 characters. This feature is often used to identify each camera when multiple cameras are installed.

Enable Night Vision Schedule

Start Time

End Time

Enable Night switch schedule by checking this checkbox.

Choose the desired start time using a 24 hr clock.

Choose the desired end time using a 24 hr clock.

Controlling User Access to the Video Stream

By default, anyone can connect to the Network Camera and view live Video at any time.

If desired, you can limit access to scheduled times, and also restrict access to known users.

To Control User Access to Live Video:

1. Connect to the Web-based interface of the Network Camera. (See Chapter 5 - Web-based Management for details.)

2. Select Video Access.

3. Set the desired options for Access.

Access

If the Video Access is disabled, users cannot connect using either their Web Browser or the Windows utility. However, viewing video is still possible by logging in as the Administrator.

Figure 17: Controlling User Access

See Chapter 5 - Web-based Management for further details about using the Video Access and User Database screens.

Making Video available from the Internet

If your LAN is connected to the Internet, typically by a Broadband Gateway/Router and Broadband modem, you can make the Network Camera available via the Internet. You will need to configure your Router or Gateway to allow connections from the Internet to the camera.

Router/Gateway Setup

Your Router or Gateway must be configured to pass incoming TCP (HTTP) connections (from Internet Viewers) to the Network Camera. The Router/Gateway uses the Port Number to determine which incoming connections are intended for the Network Camera.

This feature is normally called Port Forwarding or Virtual Servers, and is illustrated below. The Port Forwarding/Virtual Server entry tells the Router/Gateway that incoming TCP connections on port 1024 should be passed to the Network Camera. If necessary, check the user manual for your Router/Gateway for further details.

Figure 18: Connecting via the Internet

The "Port" for the Port Forwarding / Virtual Server entry above is the " Secondary Port" number specified on the Network screen of the Network Camera.

Network Camera Setup

The Network Camera configuration does NOT have be changed, unless:

x You wish to change the port number from the default value (1024).

x You wish to use the DDNS (Dynamic DNS) feature of the Network Camera.

HTTP Port Configuration

Normally, HTTP (Web) connections use port 80. Since the Network Camera uses HTTP, but port 80 is likely to be used by a Web Server, you can use a different port for the Network Camera. This port is called the Secondary Port.

The default Secondary Port is 1024. If you prefer to use a different port number, you can specify the port number on the Network Camera's Network screen, as shown below.

Figure 19: Network Screen

See Chapter 5 - Web-based Management for further details on using the Network screen.

Viewers need to know this port number in order to connect and view live Video, so you must inform viewers of the correct port number.

DDNS (Dynamic DNS)

Many internet connections use a "Dynamic IP address", where the Internet IP address is allocated whenever the Internet connection is established.

This means that other Internet users don't know the IP address, so can't establish a connection.

DDNS is designed to solve this problem, by allowing users to connect to your LAN using a domain name, rather than an IP address.

To use DDNS:

1. Register for the DDNS service with a supported DDNS service provider. You can then apply for, and be allocated, a Domain Name.

2. Enter and save the correct DDNS settings on the DDNS screen of the Network Camera.

Figure 20: DDNS Screen

3. Operation is then automatic:

x The Network Camera will automatically contact the DDNS server whenever it detects

that the Internet IP address has changed, and inform the DDNS server of the new IP address.

x Internet users can then connect to the camera using the Domain Name allocated by the

DDNS service provider.

Viewing Live Video via the Internet

Clients (viewers) will also need a broadband connection; dial-up connections are NOT recommended.

Viewing Live Video Using your Web Browser

If using your Web browser, you need to know the Internet IP address (or the Domain name) of the camera's Router/Gateway, and the correct port number.

Enter the Internet address of the Router/Gateway, and its port number, in the Address (or Location) field of your Browser.

Example - IP address:

HTTP://203.70.212.52:1024

Where the Router/Gateway's Internet IP address is 203.70.212.52 and the "Secondary Port" number on the Network Camera is 1024.

Example - Domain Name:

HTTP://mycamera.dyndns.tv:1024

+ 71 hidden pages