Sercomm 0WT01 Users Manual
Wii
W
S
e
S
r
e
r
M
M
v
v
F
F
P
P
r
r
e
S
S
e
ell
e
r,,
r
P
P
8
8
essss
e
Wii
W
A
A
0
0
d
d
1
1
H
H
P
P
a
a
rii
r
r
ell
r
e
ptt
p
v
2
v
ntt
n
essss
e
e
r
e
2
r
Uss
U
e
e
r
r
G
G
uii
u
d
d
e
e
Table of Contents
Chapter 1 Introduction 1
Features ........................................................................................................................................1
Safety Instructions......................................................................................................................1
Package Contents .......................................................................................................................3
Physical Details ..........................................................................................................................3
Chapter 2 LAN Installation 6
Procedure.....................................................................................................................................6
Chapter 3 MFP Configuration 7
Overview .....................................................................................................................................7
Using the Windows Wizard .....................................................................................................7
Chapter 4 Web -Based Management 12
Overview ...................................................................................................................................12
Preparation.................................................................................................................................12
Connecting to the Print Server...............................................................................................13
Configuration Screens.............................................................................................................13
Appendix A Specifications 20
General Specifications .............................................................................................................20
1
Chapter 1
Introduction
This chapter provides an overview of your Print Server's features.
Features
Congratulations on the purchase of your new Print Server. Your Print Server was designed to
provide a simple and efficient network printing solution. It is packed with features, including:
Ø Wireless LAN Support. Wireless stations supporting the IEEE 802.11b or IEEE
802.11g standard can interoperate with the Print Server. Both LAN and WLAN users can
print to the attached printer.
Ø Versatility. The Wireless Print Server supports all functions of MFP (Multi-function
Printer). It features a 10/100BaseT Ethernet interface port for connection to your LAN and
operating system support includes Microsoft Windows 2000, XP and Vista.
Ø Easy Installation. The Print Server makes adding printers or plotters to your network
simple.
Ø Easy Setup. A number of utility programs are supplied to simplify setup.
Ø Web-based Interface. The Web-based interface provides an easy method of
configuration in TCP/IP networks regardless of your operating system.
Ø Compact Size. This allows the Print Server to be used even where space is limited.
Safety Instructions
For your own safety, and to protect your Print Server, please observe the following safety
advice.
1. Unplug this device from its power source before cleaning. Use only a slightly dampened
cloth for cleaning. Do not use liquid or aerosol cleaners.
2. Avoid using this product near water. Exposure to water poses an electric-shock hazard.
3. Do not place the Print Server on an unstable surface. The device may fall causing serious
damage to the device.
4. This device should only be used with the power supply type specified on the marking label.
If you are not sure of type of your local power supply, consult your dealer or the local
power company.
5. Do not pinch, crimp or otherwise damage the power cord. If exposed to foot traffic,
ensures that the cable is properly shielded and does not pose a tripping hazard.
6. If using an extension cord, makes sure the total ampere rating of the products using the
cord does not exceed the extension cord's ampere rating.
7. Do not attempt to service this device, as opening or removing casing may expose you to
dangerous voltage points or other risks. Refer all servicing to qualified service personnel.
Page 1
8. The Print Server should be serviced by qualified service personnel under the following
conditions:
• The power cord is damaged or frayed.
• Liquid has been spilled onto the product.
• The product has been exposed to rain or water.
• The product does not operate normally in accordance with the operating instructions.
• The device has been dropped or the casing has been damaged.
Page 2
Package Contents
You should find the following items packaged with your Print Server. If any items are missing,
contact your dealer immediately.
• The Print Server unit
• Power Adapter
• One CD-ROM containing all support programs and this manual
• Quick Install Guide
Physical Details
Details of the LEDs and connections are in this Chapter. Further details are contained in
Appendix A - Specifications .
PS801Hv2
• 1 USB Printer Port
• IEEE 802.11g/802.11b Wireless Station
• 10BaseT/100BaseTx LAN connection
Figure 1: PS801Hv2
Page 3
LED Indicators
The Print Servers have LED indicators on the top. The Error LED is red. The Status indicator
LED is green. The LED indicator modes are described in the following table.
Status LED
(Green)
Off Off No power.
On Off Normal operation - Idle.
Flashing Off Normal operation - transmitting or receiving
On On Hardware error.
Flashing Flashing Firmware upgrade in progress.
LED Description
WLAN Off - No Wireless connection available.
LAN Off - No LAN connection
Error LED
(Red)
On - Wireless connection available.
Flashing - Transmitting or receiving data through the Wireless
LAN.
On - LA N connection available.
Flashing - Transmitting or receiving data through the LAN.
Status Description
packets from the network.
Diagnostic Push Button
The button is recessed; a pin or paper clip can be used to press it. This button has 2 functions:
• Restore the factory default settings
• Print a test page containing all current settings.
To restore the factory default settings:
1. Turn the Print Server OFF.
2. Press and hold the diagnostic button. While pressing the button, switch the Print Server
ON.
3. If you continue pressing the button for 10 seconds, a diagnostic page will be printed,
showing the new (default) settings.
To generate a Diagnostic print out
1. Ensure that both the Print Server and the attached printer are ON.
2. Press the diagnostic button, and hold it in for 2 seconds.
3. The test page, containing the current settings, will be printed.
Note:
Page 4
PostScript printers are unable to print this page. If you have a PostScript printer, the test
page will not be printed.
Page 5
Loading...