Seraphim SRP-XXX-6PB-BB, SRP-XXX-6MA-HV, SRP-XXX-6MA-BB, SRP-XXX-6PA-HV, SRP-XXX-6MB-BB Installation Manual

SERAPHIM PHOTOVOLTAIC MODULE

2017 V2

JIANGSU SERAPHIM PHOTOVOLTAIC SYSTEM CO. LTD.

ADDRESS: JIANGSU CITY OF CHANGZHOU PROVINCE WANG ZHEN HENG

ROAD NO. 1-2.

TELEPHONE: [phone]

FAX: [phone]

MAILBOX: [e-mail]

TUV VERSION

1 PURPOSE OF THIS GUIDE

1.1 APPLICABLE PRODUCTS

2 SAFETY

2.1 GENERAL SAFETY

2.2 HANDLING SAFETY

2.3 INSTALLATION SAFETY

2.4 FIRE SAFETY

3 PRODUCT IDENTIFICATION

4 MECHANICAL INSTALLATION

4.1 GENERAL INSTALLATION PRINCIPLE

4.2 LOCATION AND ANGLE SELECTION

4.3 SCREW INSTALLATION

4.4 CLAMP INSTALLATION

4.5 ELECTRICAL INSTALLATION

4.6 GROUNDING

5 MAINTENANCE

6 PARAMETERS

INSTALLATION GUIDE

FOR

SERAPHIM PHOTOVOLTAIC MODULE

CONTENTS｜1

TABLE OF CONTENTS

2

2

2

2

3

4

5

5

6

6

6

7

8

9

10

11

11

TUV VERSION

2.1 GENERAL SAFETY

2.2 HANDLING SAFETY

2｜PURPOSE OF THIS GUIDE｜SAFETY SAFETY

｜3

2 SAFETY

SRP-XXX-6PA-BB

SRP-XXX-6PB-BB

SRP-XXX-6MA-BB

SRP-XXX-6MB-BB

SRP-XXX-6PA-HV

SRP-XXX-6PB-HV

SRP-XXX-6MA-HV

SRP-XXX-6MB-HV

1 PURPOSE OF THIS GUIDE

Thanks for choosing Seraphim Photovoltaic Modules (hereafter referred to as

“PV Module”), This Guide is to give information on how to apply Seraphim

PVmodules properly.

Installers must read and understand this Guide prior to installation. For any

questions, please contact our technical department (technic@seraphim-ener-

gy.com) for further information. Installers should follow all safety precautions

described in this Guide as well as local codes when installing a module.

Keep this Guide in a safe place for future reference (care and maintenance) and

in case of sale or disposal of the PV modules.

1.1 APPLICABLE PRODUCTS

This document is applicable to the series of PV modules as listed below:

• The PV modules are qualified for application class A, which may be used in

systems operating at greater than 50 V DC or 240 W, where general contact

access is anticipated. PV modules qualified for safety through this part of IEC

61730 and IEC 61730-2 and within this application class are considered to meet

the requirements for safety class II.

• The PV modules shall be properly grounded in accordance with the instruc-

tions in this Guide or the requirements of the National Electrical Code.

• Installing PV modules requires specialized skills and knowledge. Installation

should only be performed by qualified personnel, electrical connections

requires a licensed electrician，where applicable according to local code and

law (i.e. the NEC for the USA and CEC for Canada).

• Installers should assume all risks of injury that might occur during installation,

including, but not limited to, the risk of electric shock.

• One single PV module may generate more than 30V DC when exposed to

direct sunlight. Access to a DC voltage of 30V or more is potentially hazardous.

• PV modules convert light energy to DC electrical energy, which are designed

for outdoor use. PV modules can be mounted onto ground, rooftop, vehicles or

boats etc. The proper design of support structures lies within responsibility of

the system designers and installers.

• Do not use mirrors or other magnifiers to concentrate sunlight onto the PV

modules.

• When installing the PV modules, abide to all local, regional and national stat-

utory regulations. Obtain a building permit if necessary.

• Only use equipment, connectors, wiring and support frames compatible with

the PV modules.

• Do not clean the modules with chemicals.

• Do not lift the PV module by grasping the module’s junction box or

electrical leads.

• Do not stand or step on the PV modules or place heavy objects onto it.

• Do not drop the PV module or allow objects to fall on the PV module.

• Do handle with care when move, transport and install the PV modules.

• Do not attempt to disassemble the PV modules, and do not remove any

attached nameplates or components from the PV modules.

• Do not apply paint or adhesive to the PV module top surface.

• Do not scratch or hit the back sheet.

INSTALLATION GUIDE FOR SERAPHIM
PHOTOVOLTAIC MODULE TUV VERSION

INSTALLATION GUIDE FOR SERAPHIM
PHOTOVOLTAIC MODULE TUV VERSION

NOTE：－HV: MODULES WITH 1500V