SEOWON INTECH SWC-2100 (VoIP CPE) User Manual

SEOWON INTECH

SWC-2100(VoIP CPE)

User Guide

Contents

1. VoIP CPE Overview

1.1 Product Introduction ------------------------------------------------- 4

1.2 Packaging Contents ------------------------------------------------- 5

1.3 Description of Product Functions ---------------------------------- 6

1.4 Network Configuration ----------------------------------------------- 8

2.

VoIP CPE Connection

2.1 WiMAX Wired Connection (CPE) --------------------------------- 10

2.2 WiMAX Wired PHONE Connection ----------------------------- 11

3.

PC Configuration

3.1 Windows 98/ME Setup ---------------------------------------------- 13

3.2 Windows 2000 Setup ------------------------------------------------ 17

3.3 Windows XP Setup --------------------------------------------------- 21

4. VoIP CPE built-in Web Server Access

4.1 Web Server Access ---------------------------------------------------- 26

5.

VoIP CPE WiMAX Setup

5.1. IP Address Setup ---------------------------------------------------- 27

5.2 WIMAX Modem Setup ---------------------------------------------- 28

6. VoIP CPE Setup

6.1 VoIP Setting ----------------------------------------------------------- 29

7. VoIP CPE LAN Setup

7.1 DHCP Server Setup ------------------------------------------------ 30

7.2 MAC Address Setup ------------------------------------------------ 31

7.3 LAN Status Information ------------------------------------------- 32

8. Application Support Setup

8.1 Firewall Setup ----------------------------------------------------- 33

8.2 Port Forwarding --------------------------------------------------- 34

8.3 VPN Pass through Setup ----------------------------------------- 35

9. Administrator Function Setup

9.1 Administrator Time Setup ---------------------------------------- 36

9.2 Administrator Password Setup ----------------------------------- 37

9.3 Firmware Upgrade ------------------------------------------------ 38

9.4 Administration Rebooting ---------------------------------------- 39

10.References

10.1 LAN CABLE Standard Materials ------------------------------ 40

10.2 IP Router PING Test Method ------------------------------------ 41

10.3 Product Specifications -------------------------------------------- 42

10.4 Troubleshooting

(Actions to be taken when internet is disconnected) --

43

10.5 Product Warranty and Customer Support --------------------- 45

1. VoIP CPE Configuration and Connection

1.1 Product Introduction

This product receives external WiMAX signals to construct in-building infrastructure on WiMAX
network and is covered by Ethernet network internally. The product serves as a relay as well as a
USB Modem and an internet router.
But the product is purposed to supply to users, focusing on a relay part rather than a modem.
It is also a wired and wireless internet router which allows several systems to use one internet
address supplied by high-speed internet service provider.

◎ Functional Features

Function

Features

IEEE802.16e WiMAX
Support

Wave1 = DL : 10Mbps / UL : 4Mbps

IEEE802.3u Ethe

rnet Support 10/100Mbps wired LAN connectable

RJ-11 VoIP Support 1 x RJ-11 for Analog Telephone Service

LAN Port 1 Port 10/100Mbps Ethernet Switch built-in
Cable Auto Sense Straight (Direct) or Cross Cable auto sensing

NAT function Possible of max. 253 wired and connections and internet router*
Firewall function

Manages basic firewall and IP/Port/based access

4

5

1.2 Packaging Contents

<Figure: Main Unit> <Figure: CD> <Figure: Antenna X 2>

<Figure: Quick Guide> <Figure: UTP Cable> <Figure: USB Cable>

<Figure: Adapter>

6

1.3 Description of Product Functions

<Figure: VoIP CPE Front LED part>

LED Indicator Function

PWR Power Supply stat us (On at Power ON)

LAN ON when connected to PC, Flashing at communication

PHONE ON when connected to Telephone, Flashing at communication

RSSI

Representation WiMAX received signal strength indication(RSSI), on
when the mode was selected router.

<VoIP CPE Lateral side>

Description

Item

Details

Mode Switch

-Router

-Modem

: Default Setting; Main function Mode;
Mode for WiMAX, general router function
: WiMAX Modem dedicated Mode; If VoIP CPE has no Power, you
can use WiMAX Modem function by using the USB power of
external PC.

USB

Uses external PC power; Port used when using WiMAX Modem’s
sole function

SEOWONINTECH

7

1.3 Description of Product Functions(Cont’)

VoIP CPE Rear Side

Description

Item Details

External
Antenna

ANT1: WiMAX Diversity
ANT2: WiMAX Main
Separable external antenna
User external type antenna attachable
* Antenna Classification

-3: 2.3GHz

-5: 2.5GHz

Power S/W Power On/Off Switch (On/Off by pressing right or left)

DC IN Power Adapter connection (DC12V)

PHONE Telephone connection

LAN PC or Hub connection

Factory Reset Restore the VoIP CPE Factory Default

[Note] If you lost LOGIN password for router or IP address after change, use the Reset switch to restore its
original Factory Default settings.

WiMAX
Diversity
Antenna

WiMAX

Main

Antenna

Power

Switch

Hardware

Reset

PC

Tele Phone

Power Adapter

8

1.4 Network Configuration

PC

Gateway

Internet

Local Network External Network

WiMAX

<VoIP CPE Connection Example>

LED Normal Operation Actions to be taken at failure

PWR ON when connecting adapter Check for adapter power failure

LAN

ON when cable is connected
normally

Check cable connection and PC power supply

PHONE

On when Phone cable is connected
normally

Check cable connection and Telephone

WiMAX

RSSI

Representation WiMAX received
signal strength indication(RSSI), on
when the mode was selected router.

Check the mode selected router

SEOWONINTECH

To Verify normal operation of router LEDs
You have to check if each LED of the router operates properly after connecting router, modem, and PC
with LAN cable as follows:.

Telephone

9

1.4 Network Configuration

If LED light is not in “normal operation”, check if there is any failure according to actions to be taken.
Install a router after connecting to network.

„ If normal connection between router and PC is checked, you have to set up PC and router.
„ PC setup is to control network option such as Win98/2000/XP to enable to use Internet on condition that

PC is connected to router. It is progressed by referring to Chapter II, depending on OS type.
Router setup is to connect a router to Internet, which is suitable for the Internet line type that is connected
to router. It is progressed by referring to Chapter III, depending on Internet type.

10

2.1 WiMAX Wired LAN Connection (CPE)

2. VoIP CPE Connection

PC

WiMAX

11

2.2 WiMAX Wired PHONE Connection

Telephone

12

3. PC Configuration

This chapter describes how to set up PC network environment by connecting to VoIP CPE according to
Windows operating system.
To use Internet under operating system such as Windows, the protocol called ‘TCP/IP’ is required.

For normal use of VoIP CPE, you have to set up the TCP/IP protocol normally.

In general, the condition Windows is installed first in PC is the condition router can be used, in which no
separate TCP/IP setup is required.

13

3.1 Windows 98/ME Setup

This procedure is to restore your Windows 98/ME TCP/IP settings to default values. If Windows is installed
in your PC for the first time, there is no change and check if all values are normal as the following:
After completing the TCP/IP setup of your PC, connect PC and VoIP CPE with a LAN cable according to the
instructions of Chapter 2 (STEP II) and turn the VoIP CPE on before Windows setup in order to check if IP
address is being given automatically in the VoIP CPE.
Click the Windows Start button and select Settings >> Control Panel on the menu.
Double-click the Network icon on the Control Panel window.

<Select Network Icon>

14

3.1 Windows 98/ME Setup

< Select TCP/IP > < Select Obtain an IP address automatically >

- Remove all gateways installed in Gateway. …

-Choose “Disable DNS” from DNS Configuration.

<Chosse ‘Disable DNS’ > <Remove all Gateway items>