DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
1
MPEG4/JPEG Network Camera
MODEL: SVC-3020 / 41NR (DN), SVC-3020 / 41PR (DN)
Full Manual (English)
Version 1.0
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
2
Warning
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous voltage" within the product's enclosure that may
be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying the product.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
3
Warning
This equipment has been tested and found to comply with the limits for a Class B Digital Device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment can radiate radio frequency
energy therefore, if it is not installed and used in accordance with the instruction, it may cause
harmful interference to radio communication. However, there is no guarantee th at interference will
not occur in a particular installation. If this equipment causes harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution
Any changes or modifications in construction of this device which are not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
4
Precautions
1. HEED WARNINGS
Adhere to all warnings on the appliance and in the operating instructions.
2. POWER SOURCES
Operate this equipment only from the type of power source indicated on the label. If you are not
sure of the type of power being used, consult your dealer or local power company.
3. OVERLOADING
Do not overload wall units and extension cords, as this can result in a risk of fire or electric shock.
Frayed power cords, damaged or cracked wire insulation, and broken plugs are dangerous.
Periodically examine the cord and replace it if appearance indicates damage or deteriorated
insulation.
4. POWER PLUG PROTECTION
Route the power supply cords so they cannot be walked on or pinched by items placed upon or
against them.
5. VENTILATION
Do not block the slots or openings of the video server and do not place the equ ipment on a bed,
soft rug, or other similar surface.
6. ATTACHMENTS
Do not use attachments other than those specifically recommended by the equipment
manufacturer as they may cause hazards.
7. TO PREVENT SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE
If you spill liquid on the unit, consult authorized service personnel. Moisture can damage internal
parts. Do not use this equipment near sources of water.
8. ACCESSORIES
Use only with a manufacturer recommended card, stand, tripod, bracket or ta ble. The equipment
may fall, causing serious injury to a child or adult and serious damag e to th e appli anc e.
9. CLEANING THE OUTSIDE SURFACES
Unplug this equipment from the wall outlet before cleaning. Use a damp cloth for cleaning.
10. REQUIRING SERVICE
Unplug the equipment from the wall outlet and request qualified service personnel.
11. SAFETY CHECK
Upon completion of any service or repairs to this equipment, ask the service tec hnician to perfor m
safety checks to determine that the equipment is in safe operating condition.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
5
12. IMPORTANT NOTE TO THE INSTALLER
This installation should be made by a qualified service person and should conform to all local
codes. In order to provide this product with protection against risk of unintentional operation by
employees, customers, janitors and cleaners working on the premises, and from falling objects,
building vibrations and similar causes, it is recommended this product be enclosed in the tamperresistant lock box. Make sure that the lock box is well ventilated or maintained with an air cooling
system.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
6
Table of Contents
1. Introduction of SVC-3020 ................................................................................... 8
1.1. Product Overview ........................................................................................ 8
1.2. Basic Function ............................................................................................. 8
1.3. Features .................................................................................................... 10
1.4. Packing Contents ....................................................................................... 11
1.5. System Requirements ............................................................................... 12
1.6. System Configuration ................................................................................ 13
1.7. Physical Description and Function............................................................. 14
1.7.1. Front View ........................................................................................ 14
1.7.2. Bottom View
..................................................................................................... 14
1.7.3. Rear View
......................................................................................................... 14
2. Basic Setup of SVC-3020 ......................... .. ... .. .. .. .. ............................ ... .. .. .. .. ... . 17
2.1. How to Use Lens
...................................................................................................... 15
2.1.1. Using Auto iris Lens
..................................................................................... 20
2.1.2. Using C-Mount Lens
.................................................................................... 20
2.1.3. Using CS-Mount Lens
................................................................................. 20
2.2. Installation ................................................................................................. 20
2.3. Network Setting of a PC ............................................ ............................ .. .. 21
2.3.1. Verifying the network setup status of a user PC ............................... 21
2.3.2. Operation of the Web Viewer (URL 192.168.1.10) ........................... 25
3. Configuration of Network Environment .......................................................... 29
3.1. Check-up Network Environment and Installation Type .............................. 29
3.2. Installation without a Router ...................................................................... 30
3.2.1. Basic Setup ...................................................................................... 30
3.2.2. DNS Setup ....................................................................................... 33
3.2.3. Ports Setup ....................................................................................... 34
3.3. Installation with a Router ........................................................................... 35
3.3.1. Network Setup with a Router ............................................................ 35
3.3.2 Check the configuration of a ROUTER, SVC-3020 and PC .............. 36
4. Display Mode ........................................ .. .. .. .. ... .. .. .. .. ... ............................ .. .. .. .. .. 37
4.1. Initial Log-in Screen ................................................................................... 37
4.1.1. Installation of the Web Viewer .......................................................... 37
4.1.2. Initial Log-in Screen of SVC-3020 .................................................... 38
4.2. Live Page .................................................................................................. 38
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
7
4.2.1. Screen Mode .................................................................................... 39
5. Admin Setting Mode ........... ... .. .. .. .. .. ... .. .. .. .. .. ... .. ............................ .. .. ... .. .. .. .. ... . 41
5.1. General Setting ......................................................................................... 41
5.2. Encoder Setting ......................................................................................... 42
5.3. Event Setting ............................................................................................. 44
5.4. Network Setting ......................................................................................... 48
5.5. Service Setting .......................................................................................... 49
5.5. Service Setting .......................................................................................... 50
5.6. Interface Setting ........................................................................................ 51
5.7. Motion Detect Setting ................................................................................ 54
5.8. User Setting ............................................................................................... 55
APPENDIX A. Connection Diagrams .................................................................. 56
APPENDIX B.Technical Specification of SVC-3020 ........................................... 58
APPENDIX C. Troubleshooting ........................................................................... 60
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
8
1. Introduction of SVC-3020
1.1. Product Overview
• About SVC-3020
The Intelligent Network Camera SVC-3020 provides advanced solutions for viewing, recording and
retrieving video over computer networks, including the Interne t. The SVC-3020 compresses Video,
and then transmits the compressed video over computer networks at speed s up to 30 fps (25fps in
PAL). Additionally, SVC-3020 provides audio and alarm information from the remote site.
SVC-3020 has one audio input and one alarm input. The user can listen to the remote site with the
audio input. The SVC-3020 features are accessible through the Camera browser, allowing users to
access and control their systems anytime from virtually anywhere.
1.2. Basic Function
• Real time MPEG-4 compression
When the analog video is input, the video is compressed in the MPEG-4 format. The MPEG-4 is an
optimal compressing engine that compresses video files to reduce the size of memor y. More video
files could be saved when saving from remote areas.
• Dual Codec (MPEG4 / JPEG) Support
SVC-3020 can encode analog video in either MPE G4 or JPEG. When you wish to get more vivid
image regardless of network bandwidth, JPEG format is r ecommended. SVC-3020 su pport both still
image and video in JPEG
• Stable system operation
Along with the Linux operating system, which is optimal for the embedded system, the hardware
watch-dog is used to enhance the system’s safety. The in crease in the safety of the system make s
network service stable.
• User Access Control
The SVC-3020 server performs an access control check to verify whether the user is autho rized.
If the user is not registered, the access to the 4 channel video server is blocked. Only the user with
the administrator right can set the default values and car ry out the PTZ motions of the vide o server.
Users without the administrator right (observer) can only monitor.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
9
• IP Filtering
SVC-3020 can block the access from a particular IP address through IP filtering. Only the IP
addresses recognized by the user can access the video server.
• Embedded Motion Detection function
SVC-3020 has an embedded sensor system that detects movements. The user can setup the
motion detection mode on the viewer. The observing areas of motion and sensitivity can be
regulated according to the user’s need. The user can also install various types of sensors
additionally (ex. Heat/shock/alarm sensor etc.), being connected with the video server.
• E-mail and FTP transmission
SVC-3020 sends images to the designated E-mail address or FTP Server when an alarm is raised or
movements are detected. Even when the user is not in the course of monitoring, the system notifies
the situation to the user automatically.
• Easy Firmware Update through Network
SVC-3020 users can easily enhance the functions of the system through network Firmware-Update
without having to pay additional expenses.
• Multi Viewer (16 Channel vie wer) Software
In order to maximize the performance of the SVC-3020 video server, a Multi Viewer software is
provided free of charge with other accessories. The software should be installed in a user PC. It is
capable of connecting at most 16 analog cameras and has a set of convenient features such as
presetting, emergency recording and so forth. For example, re cording starts automatically according
to the preset time and in case of emergency, it starts with a single click. Also, when playing, you can
fast-forward and fast-reverse at a high speed, which is 32 times faster than the normal playing speed.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
10
1.3. Features
Network Board
NTSC : D1 (704 X 480) at 30 fps / PAL : D1 (704 X 576) at 25 fps
Monitor live video transmitted in real-time
- Remote monitoring up to 120 fps live video
- MPEG4/JPEG
- Low network bandwidth requirement
Simultaneous video and audio signal transmission
- Bi-directional Audio
- Monitoring voices and background sounds over a single connection
Built-in Web Server and Network Interface
Power over Ethernet
No PC Needed for Operation - Standalone Unit
Linux Based Operating System
Embedded Moti on D et e c ti o n fu nction
SVC-3020 has an embedded sensor system that detects movements.
The observing areas of motion and sensitivity can be regulated according to the user's need.
Supports network environments
- Ethernet or Fast Ethernet interface
Easy Firmware Update through Network
- Firmware Update at remote sites is possible through Network
E-mail and FTP transmission
- SVC-3020 sends images to the designated E-mail address or FTP Server when an alarm
is raised or movements are detected.
Digital sensor TTL input
Alarm output
RS485 interface for Pan, Tilt and Zoom control
- Functions can be set remotely using an exclusive application
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
11
Image Module
▶ SVC-3020
Sensitivity: 00.5Lux @40IRE, F1.2.
1/3" New Structure Super HAD Interline Transfer CCD
Digital signal processing
Superior color reproduction and very low smear
Very low noise picture quality at all illumination
▶ SVC-3020-DN
Sensitivity: 0.003Lux @40IRE, built-in lens.
100x sensitivity enhancement by combination of DSS
Enhanced sharpness compensation.
Max. sense up by slow shutter is selectable to 16x/32x
Very low noise and superior picture quality .
Vari-Focal dc drive auto iris lens.
1.4. Packing Contents
SVC-3020 (DN)
MPEG4/JPEG Network Camera
UTP Cross LAN Cable CD-ROM with manual and
software
DC Adapter(12V/1A) Bracket
C-Mount Lens Adapter
Screw(3), Six Angle Wrench
Power Cable
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
12
1.5. System Requirements
Operating System : Microsoft Windows® 2000 or Windows® XP
CPU : Intel® Pentium®Ⅳ1.6Ghz or faster
RAM : 512MB or higher
VGA : AGP, Video RAM 64MB or higher
Web Browser : Internet Explorer version 6.0 or higher
Direct-X : 8.x or higher
INPUT Voltage : DC 12V / 1A
Operating Temperature: 0℃ ~ 50℃(32~122℉)
Humidity: 20~80% RHG, Non-Condensing
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
13
1.6. System Configuration
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
14
1.7. Physical Description and Function
1.7.1. Front View
1.7.2. Bottom View
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
15
1.7.2. Rear View
① SETTING SWITCH
▶ SVC-3020
Left Right
N/A N/A N/A
FL
Flickerless ON Flickerless OFF
BLC
Backlight Compensation Control
OFF
Backlight Compensation Control
ON
ALC – ELC
Auto Light Control Mode
Using Auto Iris Lens
Shutter speed 1/60
Electronic Light Co n tr o l Mo d e
Shutter Speed 1/60~1/10,000
changeable
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
16
▶ SVC-3020-DN
Left Right
DSS
Day & Night OFF Day & Night ON
D/H – D/L
* FL (Japan ese
Type)
DSS Speed High
* Flickerless ON
(Japanese Type)
DSS Speed Low
* Flickerless OFF
(Japanese T ype)
BLC
Backlight Compensation Control
OFF
Backlight Compensation Control
ON
ALC – ELC
Auto Light Control Mode
Using Auto Iris Lens
Shutter speed 1/60
Electronic Light Co n tr o l Mo d e
Shutter Speed 1/60~1/10,000
changeable
② VIDEO OUT : 1V p-p Composite, 1Channel
③ MIC. : Microphone
④ AUDIO OUT : MONO Audio Output, 1Channel
⑤ ALARM : TTL Level, Out
⑥ SENSOR : TTL Level, In
⑦ RS-485 : Port for P/T/Z control.
⑧ POWER: DC12V / 1A
⑨ RESET : Initial state which is factory default
⑩ NETWORK CONNECTOR(and PoE) : RJ-45 Ethernet Connector and socket can also be used
to Power over Ethernet
⑪ ETHERNET LED : Left LED – Yellow (Link) / Right LED – Green (Act)
⑫ ACTIVATION LED :
⑬ POWER LED : Power Supply status displays (Red LED on)
⑭ DC LEVEL CONTROLLER :
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
17
2. Basic Setup of SVC-3020
2.1. How to use Lens
2.1.1. Using Auto iris Lens
1. Please peel off about 8mm of the outer skin of the auto iris lens cable.
2. Please about 2mm of the outer skin of the insulated conductor inside the lens cable.
3. Please remove the cover of the auto iris lens connectio n plug and solder the lens cable to the
connector pin in the plug.
Lens
- Lenses are sold separately. Lenses such as an auto iris lens, CS-Mount lens and C-mount
lens can be used.
*Note*
. Please keep the lens clean.
. Any foreign objects and finger marks on the lens can cause inferior image quality in low light
level conditions.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
18
* SVC-3020 supports only DC iris Lens
4. Please replace the auto iris les connection plug cover and take off the CCD protection cap, and
then attach the auto iris lens to the camera by screwi ng it in clockwise.
5. Please insert the connection plug that is connected to the auto iris lens cable into the auto lens
connector, which is located on the side of the camera.
2.1.2. Using C-Mount Lens
Please take off the CCD protection cap and attach the C-Mount lens to the camer a by screwing it in
clockwise.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
19
2.1.3. Using CS-Mount Lens
1. Please take off the CCD protection cap and C-Mount adaptor.
2. Please attach the CS-Mount lens to the camera by screwing it in clockwise.
*Note*
- Please use the specified lens connection parts as shown in the picture below. The use of
the wrong sized parts of the wrong size may cause damage to the inside of the camera or
result in poor fitting.
- Use of a lens which is too heavy affects the balance of the camera and may cause a
malfunction. Please use a lens that weighs less than 450g.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
20
2.2. Installation
• If you use Network LAN Card in your PC, you can connect the server directly to a PC with a Cross
LAN Cable provided in the package.
• On the assumption that both the user PC and SVC-3020 are u sed under static IP, and SVC-3020
is directly connected with the user PC or Local Network, the installation procedure is to be:
Picture 2.2 Rear View
②
③
④
①
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
21
1) If you want to see the analog video, connect the monitor (LCD or CRT) with a Video Cable.
(① of [Pic.2.2])
2) In case of using the P/T/Z Controller, connect it with RS-485 Port (② of [Pic.2.2])
3) Connect the SVC-3020 to a PC with a Cross LAN Cable. (③ of [Pic.2.2])
4) Supply power on the Camera and SVC-3020 ( Be sure to use Exclusive Power Adapter )-④ of
[Pic.2.2])
5) Wait about 2 minutes after power is on the SVC-3020. The light on LINK LED shows that the
system is booted successf ully.
2.3. Network Setting of a PC
2.3.1. Verifying the network setup status of a user PC
•
To connect the SVC-3020 to the user PC, the network setting of the user PC must be verified
as in the following:
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
22
1) Go to ‘Start’ -> ’Settings’ -> ‘Control Panel’, then select ‘Network and Internet Connection’
2) Click Local Area Connection
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
23
3) Check the properties of Internet Protocol [TCP/IP]
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
24
Network Setting of User PC
4) Setup IP Address, Subnet Mask and Gateway in the user PC with 192.168.1.50,
255.255.255.0 and 192.168.1.1 as it is shown in the picture above.
• Caution
- To activate SVC-3020, the user PC must have the same network setup status as it is preset in the
SVC-3020. But when you assign the IP address, please be careful not to use the default IP written
on the back side of the video server (192.168.1.10), since the same default IP address is allotted
to all products.
- Basic network setting values of SVC-3020 are:
▶ IP Address : 192.168.1.10
▶ Subnet Mask : 255.255.255.0
▶ Gateway : 192.168.1.1
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
25
• After network setting of a PC, you can verify the network status as following:
1) Go to ‘Start’ -> ‘Run’ ->input ‘cmd’
2) When a DOS window appears as above, input ‘ipconfig'
3) The display shows the current network setting of a PC.
2.3.2. Operation of the Web Viewer (URL 192.168.1.10)
Start a Web Browser
1) Start a Web Browser and input 192.168.1.10 in URL and click ‘Enter’. Then, a user log-in
page appears. In case, it does not open, reset the video server (click the ‘Reset hole’) to bring
it to the default value, and reboot it.
2) When the ActiveX Code for ‘vg3xview _viewer’ pops up, click ‘yes’, then a message window
shows as below.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
26
3) Click ‘Install’.
4) When installation of ‘vg3xview_viewer' is completed, the initial Log-in Page appears.
Authentication Page
5) When the Authentication Page appears, input ID and Password and click ‘OK’.
- Default ID: admin
- Password: Ser (‘S’:capital letter, ‘er’: small letter)
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
27
6) And then when the Log-in Page appears, click ‘Connect’.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
28
1CH Web Viewer
5) The Web Viewer appears and images of the Camera display .
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
29
3. Configuration of Network Environment
3.1. Check-up Network Environment and Installation Type
▶To install SVC-3020 properly, basic understanding of Network Environment is required.
1) Private line Environment
In a huge complex such as Company, University, Research center, public IP addresses are
generally used. Under this environment, the user must select a Fixed IP Address for SVC-3020 (>see 3.2.1.-> 7 Network Type) . If DHCP server is available on the network, select ‘Dynamic IP
Address’. You can get the required information (IP address, subnet mask, gateway, DHCP server)
from the network administrator.
2) Broadband (ADSL, Cable, Fiber Optic) Modem Environment
At Home, in the stores and small offices a Broadband modem (DSL, Cable Modem) or a public IP
address is usually in use. In order to use several PCs sharing one Public IP address, the user need
a specific device called Router. When installing the router, input IP address of SVC-3020
(192.168.1.10) in a DMZ. If a DMZ is not available on the router, go to ‘Port Forwarding’ or ‘NAT’
application on the router and setup the ports matching to the port setting of SVC-3020.
.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
30
▶There are two types of installation:
1) Install SVC-3020 without an IP sharing device (Router)
: A router is not required, if a Cable Modem or Leased Line is used.
2) Install SVC-3020 with an IP sharing device (Router)
: A router is required under PPPoE environment. Also with a Leased Line or Cable Modem, the user
can use a router. The default IP of SVC-3020 is preset to 192.168.1.10 and Subnet Mask to
255.255.255.0 and Gateway to 192.168.1.1.
Caution 1: In case of u sing a Router or an IP Sharing Device, only public IP (Global IP) is
used.
Caution 2: A firewall keeps unwanted traffic from the internet away from your LAN computer.
Therefore, SVC-3020 may not work properly, if a fire wall is installed in a PC and some ports of
the SVC-3020 video server are closed behind a firewall. You need to open up a port, a ‘tunnel’
through the firewall to have network connection. In this case, go to ‘Setting’ -> ‘Control Panel’ ->
‘Firewall’ -> ‘Exception’ and then click ‘Add Port’ . Type the port name and number as it is preset
on the SVC-3020 video server.
▶The ports being used on SVC-3020 can be verified: ‘Log-in Page’ -> ‘Setting’->’Network
Setting’ -> ‘Port’ (->see 3.2.3. Ports Setup)
3.2. Installation without a Router
3.2.1. Basic Setup
1) After checking Video, connect SVC-3020 to a PC with a Cross LAN Cable
2) Cable connection and Network Setup should be done as it is instructed in ‘2.1. Installation
and 2.2 network setting’.
3) Run a Web Browser and input 192.168.1.10 in URL and click ‘Enter’.
The Log-in Page appears.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
31
Log-in Page of SVC-3020
4) Put ‘admin’ in ID and ‘Ser” in the Password line, click ‘Connect’.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
32
Setting Page
5) Click ‘Settings’, then ‘Setting Page’ displays.
6) Select and click ‘Network Setting’.
7) Select Network type (For SVC-3020Æ Fixed IP)
8) Input default IP Address, Subnet Mask, default Gateway of SVC-3020.
9) DNS Address should be given. (->see 3.2.2.DNS Setup.)
10) Setup Port numbers in the Port Setting Lines. (->see 3.2.3.Ports Setup)
11) Click ‘Apply’ to save setting values.
12) After Network Setting, remove the Cross LAN Cable connected between SVC-3020
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
33
and a PC.
13) Connect SVC-3020 to a Local A re a Network with a Straight LAN Cable.
14) Connect a PC to a Local Area Network with a Straight LAN Cable.
15) Video check
Run a Web Browser on your PC, input default IP of SVC-3020 in URL and click ‘Enter’,
- When Video is seen, SVC-3020 is correctly set up.
- When Video is not seen, check whether there might be IP confliction in the Network, and
re-check the network set values both of SVC-3020, and the user PC.
3.2.2. DNS Setup
▶ Network Setting -> ‘Generals’ ->
- Input First IP for DNS
- Input Secondary IP for DNS (Domain Name Server)
▪ 1st and 2nd IP address for DNS should not be the same. They should be different from
each other
▪ Please check up whether your region DNS (Domain Name Server) is correctly given. The
wrong DNS address can cause interruption of email-transmission (see 5.3. Event Setting ->
E-Mail)
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
34
3.2.3. Ports Setup
▶ Network Setting -> ‘Ports’ ->
- Set up Port number in each line of Port Setting.
▶ The default port number is preset as follows: (The user can change the port number,
if necessary; ->see 3.3.1.->12)
- HTTP Port (Web Connection Port ): Port 80 TCP
- Option Port : Port 3491 TCP
- Video Port : Port 3490 TCP
- Audio Port : Port 3499 TCP
- Control Port : Port 3495 TCP
Port Setting
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
35
3.3. Installation with a Router
3.3.1. Network Setup with a Router
1) After checking Video, connect SVC-3020 to a PC with a Cross LAN Cable
2) Cable connection and Network Setup should be done as shown in ‘2.1. Installation and
2.2 network setting’.
3) Go to ‘Network Setting’
4) Input default IP Address, Subnet Mask, Gateway of SVC-3020.
5) Input first and secondary IP addresses for DNS. In a case like this SVC-3020 is installed
with an IP Sharing Device, type the local IP of the Router in the 2
nd
DNS Address.
6) Setup Port numbers in the each line of Port Setting.
7) Click ‘Apply’ to save setting values.
8) After network setting, remove a Cross LAN connected between SVC-3020 and a PC.
9) Connect SVC-3020 to the Router with a Straight LAN Cable.
10) Connect a PC to the Router with a Straight LAN Cable.
11) Forward ports in the router to match the port setting of SVC-3020. Refer to the manual of
the router for details.
12) Checkup the network connection:
Run a Web Browser and input IP address of SVC-3020 in URL and click ‘Enter’. The
user can change the HTTP port number, if necessary. In this case, you need to
additionally input the new port number in URL: ‘http://IP Address:Port Number’
For example, if you assign the IP address of SVC-3020 to 192.168.1.10 and change the
HTTP port number from 80 to 81, you must input Http://192.168.1.10:81.
13) Check Video of SVC-3020 referring to ‘3.2.1. VIDEO CHECK’ as soon as the server has a
network connection with the IP newly set up.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
36
3.3.2 Check the configuration of a ROUTER, SVC-3020 and PC
▶ Caution: GW of a PC and SVC-3020 must accord with the IP of the ROUTER
Example:
ROUTER
IP : 192.168.1.33
SN: 255.255.255.0
SVG-3410
IP : 192.168.1.40
SN: 255.255.255.0
GW: 192.168.1.33
LAPTOP/ PC
IP:192.168.1.50
SN: 255.255.255.0
GW: 192.168.1.33
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
37
4. Display Mode
4.1. Initial Log-in Screen
4.1.1. Installation of the Web Viewer
1. Internet Explorer browser starts.
2. When the ActiveX Code pops up, click ‘yes’, then a message window shows as below.
3. Click ‘Install’.
4. When installation of ‘vg3xview_viewer' is completed, the initial Log-in Page appears.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
38
4.1.2. Initial Log-in Screen of SVC-3020
▶ Admin/User Login
When the Log-in Page appears, input ID and Password and click ‘Connect’.
Initial Log-in setting is:
- Default ID: admin
- Password: Ser (‘S’:capital letter , ‘er’: small letter)
Caution: Only the Administrator is authorized to reset the 'Setting Values'.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
39
4.2. Live Page
4.2.1. MPEG4 Screen Mode
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
40
4.2.2. JPEG Screen Mode
To change the setting values, you can move into ‘SETTINGS’.
In the ‘LIVE PAGE’, you can monitor video images transmitted from 1 channel.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
41
5. Admin Setting Mode
5.1. General Setting
General Setting
• Date/Time
1) Server Date : shows the date of operation
2) Server Time: shows real time of operation
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
42
5.2. Encoder Setting
Encoder Setting
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
43
• MPEG-4 Encoder
1) Quality: You can adjust the quality of the live video.
30~2000kbps in the Frame mode
30~2000kbps in the GOP mode
2) Frame Rate: The frame rate can be setup.
NTSC : 30, 15, 10, 7.5, 6 / PAL : 25, 13, 8, 6, 5
3) Resolution: The resolution of the live video can be setup.
NTSC : 352x240, 176x144 / PAL: 352x288, 176x144
4) Mode: The live video can be set alternatively in the frame or GOP mode.
5) Format: The video format can be setup when a camera is compatible with PAL and NTSC.
(Usually , the format is selected automatically: PAL/NTSC, according to the type of camera,)
• Audio Encoding
1) Encoding Method: shows the method of encoding
2) Encoding Bit Rate: shows bit rate of encoding
• Audio Decoding
1) Decoding Method: shows the method of decoding
2) Decoding Bit Rate: shows bit rate of decoding
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
44
5.3. Event Setting
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
45
Event Setting
• Generals
1) Pre Event dwell time:
When an alarm occurs, recording time before the occurrence of the alarm can be setup. (0~30
sec.)
2) Post Event dwell Time:
When an alarm occurs, recording time after the occurrence of the alarm can be setup. (0~120
sec.)
3) Alarm Duration:
The duration of the alarm can be setup (0~120 seconds)
• Sensor:
Title : Assign the title of each event. On the occasion of a Sensor Event, a title can be
given to an alarm display window (The number of typed letters is limited up to 32)
Sensor Type is selective:
NO (Normal Open Sensor)
NC (Normal Close Sensor)
Send FTP : On the occasion of a Sensor Event, the user can save the video images on
the assigned FTP Server.
Send E-Mail : On the occasion of a Sensor Event, the user can send an email to the
assigned Email Address.
Alarm Out : On the occasion of a Sensor Event, Alarm Out function can be activated.
• Motion Detect:
Title : On the occasion of Motion Detect, a title can be given to an email.
Send FTP : On the occasion of Motion Detect,, the user can save the video images on
the assigned FTP Server
Send E-Mail : On the occasion of Motion Detect, the user can send an email to the
assigned Email Address.
Alarm Out : On the occasion of Motion Detect, Alarm Out function can be activated.
• Alarm Out:
Follow Alarm Input : Alarm Out is operational only when Alarm Input is given.
Always On: Alarm Out is always operational regardless of Alarm Input.
Always Off : Alarm Out is always non-operational regardless of Alarm Input.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
46
• FTP Server :
The IP and directory of FTP server can be setup. The user ID/ and Password of FTP server can be
setup.
• E-Mail :
The user can assign the E-mail address to receive the notification when an event occurs. To
activate this functionality, SMTP, user ID, and user password should be properly setup as follows.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
47
▶ Check up the following to operate email-sending function properly.
• On the Motion Detect mode Æ Activate Send E-mail function
• On the E-Mail mode
- E-Mail Address: input email address of the receiver
- SMTP Address: input SMTP address of the sender
* SMTP (Simple Mail Transfer Protocol): a protocol for sending e-mail messages between servers.
- User ID / User Password : input ID/PW of SMTP to make access authorized
• Activate Authentication
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
48
5.4. Network Setting
Network Setting
• General:
The IP, Broadcast, Netmask, Gateway, DNS1, DNS2, and SMTP can be setup.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
49
• Ports:
The port number of HTTP Port, Option Port, Video Port, Audio Port, and Control Port can be setup.
• ISP Option:
- Input ISP ID
- Input ISP Password
• DDNS Option:
SVC-3020 supports DDNS operated by DynDNS and NO-IP. If you want to use DDNS service, go
to DynDNS or NO-IP webpage, create account and set up host name.
- DynDNS: http://www.dyndns.org
- NO-IP: http://www.no-ip.com/
- DDNS Type: Select either DynDNS or NO-IP.
- ID: Enter the ID for DynDNS or NO-IP account
- Password: Enter password for DynDNS or NO-IP account
- Hostname: Enter hostname when you set up on DynDNS or NO-IP webpage.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
50
5.5. Service Setting
Service Setting
• Version Information
Firmware Vers ion
MAC Address: MAC address of a video server
• Firmware Update
How to update Firmware from a distance:
1) Download the newest software from the web site which provides the firmware update file and
save it in a PC.
2) Click 'Browse' and select the update firmware file in the search window.
3) Click ‘upload’ and wait until the window shows a message of completion, and then reboot the
video server.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
51
Caution: While update is in the process, do not close or re-open a window. Also power
disconnection can cause fatal damage.
5.6. Interface Setting
Interface Setting
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
52
• RS-485
1) Title: less than 16 letters
2) Protocol:
Select a manufacturer of the camera or P/T/Z receiver. As the P/T/Z protocols are varied according
to the manufacturers. It must be set up correctly. If not, P/T/Z function does not work properly.
3) Device ID: shows a unique ID of each camera
4) Capability: According to the type of camera, some specific features can be set up and operated.
Click the feature that the user wants to activate.
▶ PTZ Controller
▪ Pan/Tilt: If the camera supports PTZ function, the user can set up and control the Degree of Pan
Rotation and Range of Tilt on the PTZ Controller of the Live Page.
▪ Zoom: activates Zoom function in two modes: ’Zoom wide’ and ‘Zoom tele’
▪ Focus: activates Focus function.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
53
▪ Iris : The camera lens has Iris function that optimizes the brightness of the screen
▪ Preset: The user can designate interesting places and give a numb er. The number can be saved
on the preset mode.
▪ System-Command: According to the protocol of the camera, some specific features can be
operated on the System Command Mode.
5) Baudrate:
Set up Baudrate to make communication with the P/T/Z receiver.
Please refer to the manual for the P/T/Z receiver to find setting values.
6) Data bit:
Select Data Bits between 7 bits/ 8bits according to the type of camera or P/T/Z receiver.
Please refer to the manual for the P/T/Z receiver to find setting values.
7) Parity:
Select Parity Bits among None/Odd/Even according to the type of camera or P/T/Z receiver.
Please refer to the manual for the P/T/Z receiver to find setting values.
8) Stop bit:
Select Stop Bits between 1bit/2bits according to the type of camera or P/T/Z receiver.
Please refer to the manual for the P/T/Z receiver to find setting values.
9) Flow Control: shows a method for the data transfer flow control.
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
54
5.7. Motion Detect Setting
- It can set up Motion Detection of SVC-3020.
- Use Motion Detect : with a click, the user can activate motion detection function.
- Sensitivity : It can set up the sensitivity of Motion Detection.
- Detection Area: It can set up Mo tion Detection Area. It is made of lattice squa res sized with
16 columns x 16 rows.
Detection Area
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
55
5.8. User Setting
- ID: Input user ID
- Password: Input user Password
- Auth: Select the user type (guest, operation User, Observer, Admin)
- Add: if you want to add a new ID on the user list, click ‘Add’
- Modify: if you want to modify a user ID, click ‘Modify’
- Delete: if you want to delete a user ID, click ‘Delete’
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
56
APPENDIX A.
Connection Diagrams
• Connection with an LED as visual Indicator
• Relay Connection
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
57
• Other Connection
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
58
APPENDIX B.
Technical Specification of SVC-3020
Network Board NTSC PAL
OS Linux 2.4
Video Compression MPEG4 / JPEG
Image Resolution Max. D1(704x480) Max. D1 (704x576)
Frame rate 30fps@D1 25fps@D1
Video out 1CH
Audio Compression G.711 PCM 64Kbps Bi-directional
Network Protocol TCP/IP, DHCP.FTP, SMPT, HTTP, PPPoE, PPP, ARP
Bandwidth Min. 32 Kbps to Max. 2 Mbps
System Requirements
Microsoft Window 98 SE or higher
Intel Pentium 800MHz or faster 256 MB or higher
Supported Web browser Internet Explorer 6.x or later
Monitoring Tools Web Browser or Monitor Software
Monitoring Via Network Maximum 20 persons
Event Notification
/ Via-E-mail
Yes
Motion Detection Yes (16 x 16)
Operation Temperature
0℃ ~ 50℃(32℉~122℉)
Alarm In/Out 1CH (NO, NC)/1CH (NO, NC)
Audio In/Out 1CH/1CH
Network RJ-45 for Ethernet 10BaseT/100BaseTX (PoE)
RS-485 Port for P/T/Z control
Power Source 12VDC /1A
Power Consumption 5 Watts
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
59
▶ SVC-3020
Image Module NTSC PAL
Image device 1/3" Sony New Structure Super HAD Color CCD
Image Processor DSP (Digital Signal Processor)
Effective Pixels 768(H) x 494(V) 752(H) x 582(V)
TV system 2:1interlace
Scan freq. 59.94Hz(V), 15.75Khz(H) 50Hz(V), 15.625Khz(H)
Synchronization Internal
H. Resolution 480TVL
Sensitivity 0.5Lux(F1.2@40IRE)
S/N Ratio More than 48dB with AGC OFF at 50IRE
Electronic Iris 1/60 ~ 1/100,000sec 1/50 ~ 1/100,000sec
White Balance 2000~8000ºK Automatic tracking
BLC Built-in, Center weighted
AGC Built-in, Factory set to ON
External Controls Video level adjustment(Iris)
Video Output VBS 1Vpp +/-10%, 75ohm
▶ SVC-3020-DN
Image Module NTSC PAL
IMAGE DEVICE 1/3" Sony New Structure Super HAD Color CCD
Image Processor DSP (Digital Signal Processor)
Effective Pixels 768(H) x 494(V) 752(H) x 582(V)
TV system NTSC PAL
Scan system 2:1 Interlace
Scan freq. 59.94Hz(V), 15.75Khz(H) 50Hz(V), 15.625Khz(H)
Synchronization Internal
H. Resolution 480TVL
Sensitivity
0.003Lux (F1.2@40IRE)
Integration Control Max. integration rate can be set to 16x or 32x by DIP switch
S/N Ratio More than 48dB with AGC OFF at 50IRE
Electronic Iris 1/2 ~ 1/100,000sec
White Balance 2000~8000ºK Automatic tracking
BLC Built-in, Center Weighted, Factory set to ON
AGC Built-in, Factory set to ON
Auto Iris Control DC Drive Iris Control w/ adjustable level
Video Output VBS 1Vpp +/-10%, 75ohm
Function . DSS ON/OFF, DSS SPEED L/H, ELC/ALC, BLC ON/OFF
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
60
APPENDIX C
Troubleshooting
Q. Video not displaying
A. No electrical power: Check electrical connections
A. Incorrect IP address: Check and correct the IP address
A. User not authenticated: Check user ID and password
A. Not connecting to network: Check PC's network settings
A. IP Camera inoperative:
Connect the video server to the IP Camera using a Cross LAN Cable
If video displays, it means that the IP Camera works properly.
Q. Video not recording
A. Time Schedule is not set up for the desired time
Set up Time Schedule for the desired time
A. Events are not recording
Check that events are set up on the Schedule Mode
A. No space on PC's hard disk
Delete some video files or change the hard disk
A. Not enough memory space of a PC
Close other PC programs
If several viewer programs are running simultaneously, stop some
viewer program(s)
Q. PTZ not working
A. Electrical power
Check electrical connections
A. Unauthorized User
Check if the User is authorized to use PTZ
A. Zoom not working
Check if the camera has a zoom lens
DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
61
Seorim Technology Co., Ltd
#1001, Daerung Technotown VI, 493-6, Gasan-Dong, Geumcheon, Seoul, Korea, 153-803
Tel: +82-2-2108-5860
Fax: +82-2-2108-5869
E-mail: sales@seorimtech.com
http://www.seorimtech.com
Q. Cannot delete ST4 file
A. Cannot delete recorded file (ST4)
Files cannot be deleted while playing
Stop playing and del ete
Loading...