SentrySafe EF3428E, EF4738E User Manual

OWNERS MANUAL

Gun and Executive Safes

TABLE OF CONTENTS

Unbolting your gun safe from the shipping pallet ......3

Bolt-down instructions ..............................................3

Lock instructions ....................................................4-5

Lock instructions: For safes with 3-number

combination lock / dual combination key lock ........4

Lock instructions: Standard electronic lock / dual

combination key .................................................4-5

Serial Number, Combination, Factory Code and

Generic Code .............................................Back Cover

MANUEL D’UTILISATION

Coffres-forts pour armes à feu et

exécutif

TABLE DES MATIÈRES

Déboulonner le coffre-fort pour armes à feu de sa

palette d’expédition ............................6Instructions de

boulonnage .............................................................. 6

Instructions de verrouillage ....................................7-8

Instructions de verrouillage : pour les coffres-forts

avec une serrure à combinaison à 3 numéros / une

serrure double à clé et à combinaison ................... 7

Instructions de verrouillage : serrure électronique

standard / double à clé et à combinaison .............. 8

Numéro de série, combinaison, code d’usine et code

générique ....................................... Couverture arrière

MANUAL DEL DUEÑO

Cajas fuertes de armas de fuego

y de ejecutivos

ÍNDICE

Desempernado de su caja fuerte de armas de fuego de

la bandeja de embarque ........................................... 9

Instrucciones de apernado ........................................10

Instrucciones de enclavamiento............................10-11

Instrucciones de enclavamiento: Para cajas fuertes con cerradura de combinación de 3 números / cer-

radura de llave de combinación doble ..................10

Instrucciones de enclavamiento: Cerradura elec-

trónica estándar / llave de combinación doble ......11

Número de serie, combinación, código de fábrica y

código genérico ....................................Contraportada

•••IMPORTANT•••

DO NOT RETURN SAFE TO THE STORE!

If you experience

any

problems

or challenges with your safe, please

resolved quickly

without

the

product being returned.

www.sentrysafe.com

900 Linden Avenue / Rochester, New York / 14625-2784 USA

Customer Service: 1-800-828-1438

Fax: 585-381-2940

•••IMPORTANT•••

NE RETOURNEZ PAS LE COFFRE FORT

Á LA MAGASIN!

Si vous rencontrez

des

problèmes

ou des difﬁcultés avec votre coffre-fort,

veuillez nous contacter. De nombreux

problèmes peuvent être résolus

rapidement

sans

avoir à retourner

le produit.

•••IMPORTANTE•••

NO REVUELVA LA CAJA FUERTE

A LA TIENDA.

Si llega a tener

algún

problema

o diﬁcultad con su caja fuerte, favor

de contactarnos. Muchos asuntos

se pueden resolver rápidamente

sin

tener que hacer una devolución

del producto.

El Departmento de Servicio al Cliente:

Debe marcarse un código de acceso antes de marcar el número 800. Es un proceso de 2 pasos. Paso 1: marque 01 800 112 2020 ó 001 800 658 5454 Paso 2: a la indicación marque 1-800-451-0821

401147

Thank you for purchasing this SentrySafe gun safe product.

Please read this manual before using this product.

We are pleased that you have chosen one of our gun safes to protect your ﬁrearms. You can be assured that your safe meets the California Department of Justice standards for ﬁrearm safety. This manual will provide you with the information you need to:

• unpack and set up your safe

• open the safe

• operate the lock

• take full advantage of your safe’s special features.

Remember to keep your combination a secret. Writing down a combination and putting it in a desk drawer is like leaving your door key under the mat – it invites entry.

Please retain this manual for your records. If you have any questions about your gun safe, please visit our website at www.sentrysafe.com or call Sentry Customer Service at 1-800-828-1438 or 1-585-381-4900. Customer Service representatives are ready to assist you, 8 a.m. to 6 p.m., E.S.T., Monday - Friday.

Unbolting your gun safe from the shipping pallet

WARNING!

This is a two-person operation and should not be attempted without help. Before attempting to unbolt your new safe,

be certain someone is with you to help steady the safe while you work. Ensure the safe is standing upright on a ﬂat, level surface. (Fig. A)

NOTE: Sentry Group is not responsible for any costs incurred for unit to be removed from pallet and installed in place.

UNBOLTING YOUR GUN SAFE FROM THE SHIPPING PALLET

Tools/equipment required

• Adjustable wrench, pliers, or 17 mm (11/16”) socket wrench

• Hammer

1. Using a wrench or pliers, remove the nuts located under the X-cut in the carpet in the bottom of the unit. (Fig. B)

NOTE: If the bolts turn when you begin to remove the nuts, reach between the slats of the pallet and hold the bolts, by hand and/or with pliers, as you turn the nuts.

2. Once the nuts are removed, use a hammer to tap the bolts through the bottom of the safe.

3. Close door and put handle in locked position.

4. With your helper, slide safe to one edge of pallet. Tip the safe so that the edge moves to the ﬂoor.

(Fig. C)

5. Remove the pallet and stand the safe upright on the ﬂoor.

Bolt-down instructions

To help provide maximum security, SentrySafe strongly recommends this safe be bolted down. (Hardware supplied)

1. Select a suitable and convenient location for your safe. Set the safe in place and use the holes provided in the bottom or back of the safe to mark the location of the holes to be drilled in the ﬂoor or wall. It is not recommended to attempt to bolt to both ﬂoor and wall. If bolting to a wall, please ensure that the safe is resting ﬁrmly on the ﬂoor.

Note: Fire-Safe models cannot be bolted to the wall.

2. Move the safe away and drill holes of the appropriate diameter and depth for the type of hardware and the mounting surface being used (2 each – bolts, washers and masonry anchors).

3. Place the safe back over the holes and install the fasteners as required. If a water resistant unit was purchased, rubberized washers are provided. Assure that the area around the safe hole opening is clean using a damp cloth. Place the rubber side of the washer facing down against the safe ﬂoor and install the fastener.

NOTE: SentrySafe is not responsible for any costs incurred if unit is to be replaced.

Lock instructions

Gaining Entry into Safes with Combination Locks

3-Number Combination Lock and Dual Combination Key Lock

NOTE: See the sticker on the back cover of this manual for your combination.

IMPORTANT: The lock on this safe is in the open position. DO NOT operate the combination until ﬁrst reading and understanding the following instructions.

Gaining Entry into Safes with Electronic Locks

WITH DOOR OPEN!

Test your combination several times

To unlock and open

Before dialing your combination, simply insert the key (if equipped) in the lock and turn clockwise.

1. Start the dial at ZERO.

2. Turn the dial to the left. Make sure ZERO passes the pointer at least THREE times. Then

Test ﬁrst

with the door open.

stop at the first number of your combination.

3. Turn the dial to the right. Stop the

SECOND time you reach the second number of your combination.

4. Turn the dial to the left. Stop the FIRST

time the pointer reaches the third number of your combination.

To Close and Lock

With the door closed, turn the handle counterclockwise to secure the locking bolts, then spin the combination dial to the left at least four times to scramble the combination.

Standard Electronic Lock and Dual Electronic Key Lock

To activate lock:

Four alkaline AA batteries, Voltage: 6Vdc, (not included) are required to activate the keypad.

NOTE: Non-alkaline and rechargeable batteries ARE NOT RECOMMENDED.

To install batteries:

1. Using two hands, hold the keypad, thumbs down, on its left and right sides. Push up

its wires. This will expose the battery holder. (Fig. B)

3. Install four alkaline AA batteries as illustrated on the back of the battery holder.

4. Reconnect the keypad by inserting the keypad’s four posts into the matching holes.

5. Push down to snap into place.

the keypad with your thumbs,

and disconnect it from the safe by pulling it towards you. (Fig. A)

2. Let the disengaged keypad hang by

Test ﬁrst

WITH DOOR OPEN!

(See back cover of this manual for your

factory code.)

Test your factory code several times with the door open.

NOTE: Only a light touch is needed. A green PROCEED light and a single beep indicate that the keypad “felt” your touch. The lock allows 5 seconds for each key press. If you pause longer, an error signal will occur (blinking red light and three beeps), indicating you should start over.

For safes with dual combination key lock insert key and turn clockwise.

1. Press the 5-digit factory code. The green light will come on.

2. Turn the handle clockwise and open the door.

Access codes

There are three possible ways to unlock and access the safe—by entering its preset Factory Code, your own User Code or a User PIN (Personal Identiﬁcation Number).

You can always open the safe by entering the 5-digit Factory Code. This code cannot be deleted.

But if you prefer to use your own code, you can program the safe to open to the 5-digit User Code of your choice. If you wish to give someone else temporary access to the safe, you can program a User PIN that can later be erased.

Programming a user code

There are two ways to program a user code. A 1. Press the Program key. (Prog.)

2. Enter the Factory Code. The green LED remains ON while you enter the 5-digit user code of your choice. After 5 digits are entered the green LED turns OFF.

(To enter a new User Code, repeat these steps.)

B 1. Press the red button on inside of door (hinge

side). The lock will “beep” and the green LED will come on.

2. Enter a 5-digit user code. (To enter a new User Code, repeat these steps.)

Keep your new user code secure

For your records, please copy it here:

_____ _____ _____ _____ _____

Programming a user PIN

1. Press the Program key.

2. Press it a second time.

3. Enter your 5-digit User Code. The green LED remains ON.

4. Enter the 5-digit User PIN of your choice (any combination except 00000.) After 5 digits are entered, the green LED turns OFF.

(To enter a new User PIN, repeat these steps. To erase the User PIN, press Program twice, enter your User Code and then enter 00000.)

Key override

If your electronic lock fails or you do not have any codes available, you may use a key override to access this unit.

1. Using two hands, hold the keypad, thumbs down, on its left and right sides. Push up the keypad with your thumbs, disconnect and remove the battery holder.

2. Insert the skeleton key into the key hole inside the opening for the battery.

3. Turn the key to the right.

4. Open the door.

+ 8 hidden pages