Sentry Saf-T-Vise STV-HP1 Original Instructions Manual
Original Instructions
Installation, Operation
&Maintenance Manual
Saf-T-Vise STV-HP1
Insertable Tool Holders
S-CM-IOM-00506-1 03-19
Do not install, maintain, or operate this equipment without reading, understanding, and following the
appropriate Sentry Equipment Corp instructions. Otherwise, injury, damage, or both may result.
Copyright
© 2019 by Sentry Equipment Corp. All rights reserved. All product and company names are property of their respective
owners. This document contains proprietary information. No part of this document may be photocopied or reproduced
without the prior written consent of Sentry Equipment Corp.
Limit of Liability
Sentry Equipment Corp, its employees, agents, and the authors and contributors to this document speci cally disclaim
all liabilities and warranties, express or implied (including warranties of merchantability and tness for a particular
purpose), for the accuracy, currency, completeness, and/or reliability of the information contained herein and/or for the
tness for any particular use and/or for the performance of any material and/or equipment selected in whole or part
with the user of/or in reliance upon information contained herein. Selection of materials and/or equipment is at the
sole risk of the user of this publication.
Note
The information contained in this document is subject to change without notice.
2 Sentry Equipment Corp
Table of Contents
Safety Information .........................................4
General Safety Precautions .................................5
General Description ........................................6
Specications ..............................................6
Saf-T-Vise SVT-HP1 Insertable Tool Holder Specications ..............6
Installation and Operation ..................................6
Maintenance ...............................................7
Inspecting the Safety Cap ............................................7
Prepping the Tool Holder for Reinstallation ...........................7
Cleaning the Rod/Probe Shaft ........................................7
Changing a Rod/Shaft and Replacing a Seal ..........................8
Changing a Coupon/Checking Probe End ............................10
Troubleshooting ...........................................11
Leaks ................................................................11
Locking Collet .......................................................12
Standard Warranty .........................................12
Customer Support ..........................................13
Saf-T-Vise STV-HP1 3
Safety Information
Please read the entire manual before attempting to unpack, set up, or operate this product. Pay careful attention to all
Warnings, Cautions, and Notes. Failure to do so could result in serious personal injury and/or equipment damage.
Use of Hazard Information
If multiple hazards exist, the signal word corresponding to the greatest hazard shall be used.
De nitions
DANGER indicates a hazardous situation which, if not
SHALL:
SHOULD:
avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION, used with the safety alert symbol, indicates a
hazardous situation which, if not avoided, could result in
minor or moderate injury.
 NOTE
Information that requires special emphasis.
 TIP
Alternate techniques or clarifying information.
This word is understood to be mandatory.
This word is understood to be advisory.
NOTICE is used to address practices not related to personal
injury.
4 Sentry Equipment Corp
General Safety Precautions
Product Selection, Installation, and Use
Improper selection, installation, or use can cause personal injury or property damage. It is solely the responsibility of users,
through their own analysis and testing, to select products suitable for their speci c application requirements, ensure they are
Potential Equipment Hazards
properly maintained, and limit their use to their intended purpose.
Follow proper local, state, and federal regulations for proper installation and operational requirements.
Always use caution and common sense when working with any chemical. Read the product label and Material Safety Data
Sheets (MSDS) carefully and follow the instructions exactly.
Hot surfaces! This equipment may have very hot surfaces. If an operator contacts a hot surface, injury may occur. Use
protective clothing to prevent injury. If other equipment comes in contact with a hot surface, damage to the equipment may
occur. Ensure the area around this equipment is kept clear to prevent damage from occurring.
High pressures! This equipment may contain uids at very high pressures. Prior to installing, removing or maintaining this
equipment, ensure that the equipment is isolated from all connecting piping, the equipment is depressurized, the contents
have been drained, and the equipment is cool.
Saf-T-Vise STV-HP1 5
Loading...