Garden sauna LAVA
375 x 319 x 270 cm
Assembly Instruction
DE
EN
Version 10/17
Assembly instructions
EN
Garden sauna
LAVA
Exterior dimension:
375 x 319 x 270 cm
Interior dimension:
200 x 200 x 210 cm
200 x 104 x ~260 cm
Wall thickness:
70 mm
There may be slight deviations in the dimensions.
Subject to technical modifications and misprints.
Dear customer,
Before you begin with the work, check that all the individual parts have been delivered against the parts list.
Ifyou discover any missing parts, notify your dealer within 14 days of receiving the sauna cabin.
Keep the delivery note, the invoice and the assembly instructions in a safe
place in case of any questions.
You require the following tools:
1 hammer with a wooden head or a rubber hammer
1 cordless screwdriver with bits for cross-head screws and Torx
1 roller tape measure
1 drill bit Ø10 mm; 1 drill bit Ø3 mm
1 spirit level
1 pencil
You need an assistant for the assembly. We also advise you to pre-drill the holes for
thescrews.
02
The electrical connection may only be performed by a qualified electrician or similarly
qualified person.
!
Front face with doors
1 block plank 341 x 7 x 7 cm
with recess for door
3 block planks 341 x 14.6 x 7 cm
1 block plank 375 x 16.5 x 7 cm
14 block planks 26.5 x 14.6 x 7 cm
10 block planks 232.5 x 14.6 x 7 cm
4 block planks 55 x 14.6 x 7 cm
4 block planks 58 x 14.6 x 7 cm
1 door frame incl. door 198 x 80 cm
1 window 119 x 69 x 7 cm
2 interior door panels 76 x 5.5 x 2 cm
2 interior door panels 205 x 5.5 x 2 cm
Right and left sides
32 block planks 230 x 14.6 x 7 cm
2 block planks 254.5 x 14.6 x 7 cm
2 block planks 295 x 14.6 x 7 cm
2 block planks 210 x 14.6 x 7 cm
Rear face
1 block plank 375 x 16.5 x 7 cm
1 block plank 341 x 6.5 x 7 cm
1 block plank 341 x 14.6 x 7 cm
with ventilation recess
15 block planks 341 x 14.6 x 7 cm
Wall elements
28 block planks 81 x 14.6 x 7 cm
1 block plank 230 x 14.6 x 7 cm
with recess for door
3 block planks 230 x 14.6 x 7 cm
Roof
34 roof boards 375 x 10 x 1.9 cm
3 block planks for roof 319 x 14.6 x 7 cm
2 weather boards 378.5 x 13.5 x 2 cm
2 weather boards 317.5 x 13.5 x 2 cm
2 roof support slats 200 x 4 x 4 cm
2 roof support slats 192 x 4 x 4 cm
2 roof elements 199 x 99 x 6.5 cm
Floor
2 oor frames 206 x 12 x 4 cm
4 oor frames 206 x 8 x 4 cm
1 oor frames 206 x 16 x 4 cm
2 oor frames 325 x 8 x 4 cm
21 oor boards 199.5 x 9.5 x 1.9 cm
21 oor boards 103.5 x 10 x 1.9 cm
2 skirting boards 103.5 x 2.5 x 2.5 cm
6 skirting boards 200 x 2.5 x 2.5 cm
5 bench support slats 4 x 4 cm
(3 pcs. 58 cm; 2 pcs. 116 cm)
1 bench 137.5 x 62 cm
2 benches 199 x 62 cm
2 back rests
2 head rests
1 bench screen 199 cm
1 door frame 202 x 72 cm
1 interior light
1 light screen
1 oor grid 70 x 50 cm
1 heater safety guard, 2 parts
1 ventilation shutter
1 assembly material set
1 assembly instructions
6 threaded rods 224 x 8 mm incl. nuts
3 silicon cables 5 x 1.5 mm²
20 m² roong felt
LAVA parts list
The parts list can also be used as a claims sheet.
03
04
LAVA GARDEN SAUNA
Notes for the planning permission, foundation,
anchorage, delivery and unloading
Planning permission
Before installing the garden sauna, make sure you enquire about whether planning
permission is required at your local planning authority (municipal oce, magistrate).
Youmay need this as permission is required above a certain room volume. This depends
on where you live exactly and is therefore handled dierently from country to country.
Check with your local planning authority (municipal oce, magistrate)
with respect to the building regulations and load standards.
Concrete foundation:
A solid concrete foundation is important for the durability as well as the safety of your
garden sauna.
We recommend having the foundation laid by a specialist.
It is the basis for a proper anchorage of your garden sauna. Only then can you ensure
that there will be no diculties with assembly and use.
There are several ways that you can lay the foundation for your garden sauna.
Assembly instructions
EN
05
However, the two options below have proven to be the best in practice:
• Foundation slab (base plate)
• Strip foundation
For both types, a foundation that is absolutely at and load-bearing must be ensured. Only then
can the assembly of the individual modules be ensured without diculties and with a precise t.
Once the concrete slab has been completed and dried out, we recommend torching it
with roong felt or torch-on felt in order to seal it completely.
Foundation slab (base plate)
A base plate ensures a frost-proof foundation for the garden sauna. Note that structural
steel mesh mats must be laid in the concrete (reinforced) in order to achieve maximum
stability and protect the slab from cracking.
Ground
Concrete 15 cm thick
Gravel 15 cm thick PE-lm
06
Strip foundation
Depending on the structural requirements and local conditions, strip foundations can be
laid in dierent ways. There are two types of strip foundations:
• strip foundation - not reinforced
• strip foundation - reinforced
To make a frost-proof strip foundation, you must dig at least 80 cm deep into the ground.
The supporting walls of the garden sauna are then laid on the foundation strips.
This construction has the advantage that the base plate can be thinner and less
reinforcement is necessary.
The foundation should be about 10 to 15 mm smaller than your garden sauna so
that water can run o the outer walls of the garden sauna and the outer sides of
thefoundation.
Assembly instructions
EN
80 cm
30 cm
Gravel 10 cm thick
PE-lm
Concrete 10 cm thick
Ground
07
Note:
The foundations must be absolutely at to ensure the load-bearing capacity of the sauna. If the
foundation slab is larger than the oor space of the garden sauna, rainwater can start to collect
around the garden sauna. This means that the wooden wall elements would be constantly
standing on wet ground. This could result in the wood absorbing the water and starting to rot.
We point out that we do not accept any liability for the resulting damage.
Anchoring the garden sauna:
It is essential that the garden sauna is rmly anchored on the base plate or the strip
foundation. Strong winds can exert a powerful force on the garden sauna. To prevent
damage to your property or third-party, property proper anchoring is essential.
We point out that anchoring the garden sauna is the responsibility of
the customer and we do not accept any liability for accidental damage.
Wood protection outside:
The wood of the garden sauna is untreated. If you want to increase the life of your garden
sauna, we recommend painting with a suitable protective painting.
Roong:
The included roong felt serves as an initial cover. We also recommend to cover the roof
with bitumen shingles, sheet metal or a suitable foil.
Delivery of the garden sauna:
The garden sauna is delivered by lorry (also possible by semi-trailer truck).
Access to the unloading area must be ensured.
For the unloading and assembly of the garden house at least two persons are necessary.
Screws 5 x 100 mm
08
Assembly instructions
EN
Fig. 1.3
Fig. 1.1
Fig. 1.2
Screws 5 x 100 mm
Base frame for
outer sauna
Loading...